ESAB MIG C250i Bedienungsanleitung

MIG C250i

Instruction manual

Welding Power Source

MIG C250i

Instruction manual

For

Installation, Operation & General maintenance

SAFETY

Precautions for installation

Beware of electric shock!

Install grounding device according to application standard.

Do not touch live parts with naked skin, wet gloves or wet clothes.

Be sure you are insulated from ground and work piece.

Cover the cover plate of the machine before power on to avoid an

electric shock.

Confirm the safety of your working position.

Beware of fire hazard!

Please install the machine on non-combustible materials to avoid

a fire.

Make ensure there are no inflammables near the welding position

to avoid a fire.

Beware of explosion!

Do not install the machine in an environment with explosive gas

to avoid an explosion.

Replacing the components can be dangerous.

Only professionals can replace the components of the machine.

Make sure the connecting wires inside the machine are correctly connected after replacing the

PCBs, and then the machine can be run. Otherwise, there is a risk of damage to property.

Make sure there are no foreign bodies such as wire leads, screws, gaskets and metal bars

falling into the machine inside when replacing the components.

Carrying or moving the machine can be dangerous.

Cut the input power off via the switching box before moving the welding machine.

The handle can only be used for moving the welding machine by hand in short distance, and

it cannot be used for lifting. Otherwise, personal injury or property damage may be caused by

a drop.

Make sure that the flying rings are tightened, and that the machine enclosure and cover are

fixed when moving the welding machine with a crane,

Two lifting belts should be used when lifting the welding machine, and the angle formed by the

lifting belt and the vertical should be smaller than 15°.

Do not apply any stress on the operation panel and cover when moving the welding machine.

Otherwise, personal injury or property damage may be caused by a drop.

Do not install and run the welding machine when the machine is damaged or lacks any

components. Otherwise, fire hazard or personal injury may be caused.

Precautions for operation

Smoke-may be harmful to your health!

Keep your head away from the smoke to avoid inhalation of waste

gas in welding.

Keep the working environment well ventilated with exhaust or

ventilation equipment when welding.

Arc radiation-may hurt your eyes and burn your skin!

Use proper welding mask and wear protective clothing to protect

your eyes and body.

Use proper mask or curtain to protect onlooker from being injured.

Magnetic field can make cardiac pacemaker a bit wonky.

People with cardiac pacemaker should consult the doctor before

carrying out welding.

Stay away from the welding source to reduce the effect of magnetic

field.

Improper use and operation may result in a fire or an explosion.

Welding spark may result in a fire, so please make ensure there are

no inflammables near the welding position, and pay attention to fire

safety.

Ensure there is fire extinguisher nearby, and make sure someone

has been trained to operate the fire extinguisher.

Do not weld closed container.

Do not use this machine for pipe thawing.

Hot work piece can cause severe scald.

Do not touch hot work piece with bare hands.

Cool the welding torch for a while after continuously working.

Excessive noise does great harm to people’s hearing.

Wear ear covers or other hearing protectors when welding.

Give warning to onlooker that noise may be potentially hazardous to

hearing.

Moving parts may injure your body.

Please keep away from moving parts (like fan).

Each door, panel, cover, baffle plate, and protective device the like

should be closed and located correctly.

Seek professional support when trouble strikes.

When trouble strikes in installation and operation, please inspect

according to related contents in this manual.

If you still cannot understand fully, or you still cannot solve the

problem, please contact the service center to obtain professional

support.

TABLE OF CONTENTS

1. SAFETY....................................................................................................1-3

Technical parameters ..............................................................................5

2. INSTALLATION AND CONNECTION ..........................................................2

Installation requirements............................................................................

Electrical connection..................................................................................

3. OPERATION.............................................................................................7-9

Panel functions of MIG C250i ..................................................................

Operation of the panel functions................................................................

Input Power Supply ...................................................................................

Wire Feeding Mechanism..........................................................................

Work after welding.....................................................................................

4. MAINTENANCE .....................................................................................9-11

Daily maintenance.....................................................................................

Periodic check...........................................................................................

5. TROUBLESHOOTING..........................................................................12-13

6. WIRING DIAGRAM....................................................................................14

7. SPARES LISTAND EXPLODED DIAGRAM ........................................15-17

Technical Parameters of MIG C250i

Description

Specification

Model

MIG C250i

Input Voltage V

1Phase 220V

3Phase 415V

Frequency Hz

50/60

Rated input current A

14.8

Rated KVA

10.3

10.8

MMA welding current A

20A~200A

MIG welding current A

30A~250A

Welding current（10min）A

60%@250

Efficiency η

85%

Power factor Cosφ

0.9

Insulation class

Enclosure protection IP

21S

Cooling type

Fan cooled

Weight Kg

Dimension L×W×H mm

1000*490*730

The MIG C250i series is a DC inverter compact MIG welding machine with MMA

function. This unit uses 1~Phase 220V, 50/60Hz or 3~Phase 415V, 50/60Hz input AC

power.

INSTALLATION AND CONNECTION

Installation requirements

1) Environment requirements

a) Do not install the machine at places with excessive dusts and metal powders.

b) Do not install the machine at places with corrosive or explosive gas.

c) The temperature of the working environment should be between -10℃and 40℃.

d) Do not carry out welding with the welding machine placed on a platform with a pitch

greater than 15°.

e) The machine should be installed in a well-ventilated place with humidity of 90% or

less and without water condense.

f) Pay attention to the wind at the welding site, and use wind deflector if necessary.

Otherwise, the welding process will be affected.

2) Installation space requirements

The welding machine should be at least 20cm away from the walls, and there

should be at least 30cm between them when two machines are installed side by side.

Please refer to the table below to determine the installation position of the welding

machine. Table 2-1: Reserved space when installing the welding machine

Machine part

Front

Top

Left

Right

Rear

Reserved space

≥20cm

≥10cm

≥20cm

Electrical connection

•High voltage danger from power source! Consult a qualified electrician for proper

installation of receptacle. This welder must be grounded while in use to protect the

operator from electrical shock.

• Do not remove grounding connection or alter the plug in any way. Do not use any

adapters between the welder’s power cord and the power source receptacle. Make

sure the POWER switch is OFF when connecting your welder’s power cord to a

properly grounded input AC supply.

OPERATION

Panel Functions of MIG C250i

Serial

No.

Part name

Function

Current meter display

To display the welding current value.

Voltage meter display

To display the welding voltage value.

Wire Inching switch

To feed wire without welding.

2 / 4 Stroke

2 or 4 stroke operation in MIG.

Welding Process Selection

MIG or MMA Selection.

Voltage Control

Voltage adjustment in MIG

Current Control

Wire Speed/ Current Control in MIG/ MMA.

Positive Output

Positive Output Terminal

Output Selection

MIG Polarity Change Cable

Negative Output

Negative Output Terminal

Torch Connector

Euro type MIG Torch Connection

LEDS

Power On / Over Heating

Inductance Control

Inductance Adjustment in MIG mode

Rear panel

Input Power Supply

This unit uses 1~Phase 220V, 50/60Hz or 3~Phase 415V, 50/60Hz input AC power.

3 Phase supply connection:

Connect 3 Phase 415V, 50Hz input power supply (R, Y, B and Ground) to the

corresponding R, Y, B and ground wires of the power source.

1 Phase Supply connection:

Connect 1 phase 220V, 50Hz input power supply to “RED” and “BLACK” wires and

ground wire of the power source.

Wire Feeding Mechanism

Wire Feeding mechanism is inbuilt inside

the machine. Wire Spool mounting and

feed roller assembly both are available

on the right side of the machine.

Work after welding

1) Cut off the power of the welding machine 3~5min after the welding work is finished,

so as to cool the internal of the machine.

2) Turn off the air switch on the welding machine first and then switch off the power

in the switching box when shutting off the power.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB migmaster 215 pro Bedienungsanleitung

ESAB

ESAB AristoFeed 30- 4 Bedienungsanleitung

ESAB

ESAB Caddy Tig 1500i Bedienungsanleitung

ESAB

ESAB EMP 320ic Bedienungsanleitung

ESAB

ESAB Origo A32 Bedienungsanleitung

ESAB

ESAB 100i Bedienungsanleitung

ESAB

ESAB Caddy 150 Bedienungsanleitung

ESAB

ESAB Thermal Dynamics CUTMASTER 40 Bedienungsanleitung

ESAB

ESAB LTG 410 Bedienungsanleitung

ESAB

ESAB Powercut 650 Bedienungsanleitung

ESAB

ESAB TXH Series Bedienungsanleitung

ESAB

ESAB A6TF F1 Bedienungsanleitung

ESAB

ESAB Caddy Tig 1500i Bedienungsanleitung

ESAB

ESAB Heliarc SR-9 Leitfaden

ESAB

ESAB ST-16 Bedienungsanleitung

ESAB

ESAB YardFeed 200 Bedienungsanleitung

ESAB

ESAB Aristo Mig 5000i 400 V Bedienungsanleitung

ESAB

ESAB Origo Tig 3001i Bedienungsanleitung

ESAB

ESAB THERMAL DINAMICS CUTMASTER 60i Bedienungsanleitung

ESAB

ESAB Aristo Mig 5000i 400 V Bedienungsanleitung

ESAB

ESAB EMP 210 Bedienungsanleitung

ESAB

ESAB Fabricator EM 401i Bedienungsanleitung

ESAB

ESAB Origo M 12 Feed 304 Bedienungsanleitung

ESAB

ESAB 35833 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung