Et ET1000 Bedienungsanleitung

ET1000 Sliding gate operator

Commercial/industrial 1000kg mass

support@et.co.za

G&C Electronics cc. T/A ET Systems

1 Nelson Rd, Observatory, Cape Town, South Africa

www.et.co.za

Technical specifications may change without prior notice.

All goods are subject to the standard factory warranty as laid out on the last page of this

publication

Rev: 2008/10/003

WARNING TO THE INSTALLER. GENERAL SAFETY

OBLIGATIONS.

Caution! It is important for personal safety to follow all the instructions carefully. Incorrect

installation or misuse may cause serious personal harm.

Keep the instructions in a safe place for future reference.

This product was designed and manufactured strictly for the use indicated in this

documentation. Any other use not expressly indicated in this documentation, may

damage the product and/or be a source of danger.

We accept no responsibility due to improper use of this product.

Care must be taken not to install this product in an unsafe environment. I.e. near

inflammable gases and or fumes.

We will not accept responsibility if the principles of good workmanship are disregarded by

the installer. The construction of the gate must be sound and automatable. It is the

responsibility of the installer to ensure that all mountings to the gate are sufficient to

withstand the necessary forces incases of overload.

Before carrying out any work on the product, ensure that the electrical supply is switched

off.

It is highly recommended that a set of safety infra red beams be used in conjunction with

this product.

We accept no responsibility regarding safety and correct operation of the automation if

other manufacturer’s equipment is added to this product.

Do not make any modifications or alterations to this product.

It is the responsibility of the installer/ service provider to completely instruct and

demonstrate the proper use of this product, especially the emergency override, to the end

user. It is also the responsibility of the installer/ service provider to issue all end user

documentation, which accompanies this product, to the end user.

Ensure that other persons, especially children are clear of the gate and opener before and

during operation.

Keep remote transmitters away from children to prevent accidental activation of the

system.

The end user should refrain from attempting to make any repairs or adjustments to the

system and should contact professional qualified assistance timorously.

Anything other than expressly provided for in these instructions is not permitted.

The electrical supply to this product must comply with the local electrical code of practice

and any electrical work must be carried out by a qualified electrician.

Over and above the recommendation to use safety infra red beams with this product it is

mandatory to ensure a set has been installed and is in proper working condition when

using the automatic closing feature.

1. INTRODUCTION.

1.2. Technical speci ications.

Model ET 1000

Power supply 220Vac +/- 10% 0Hz

Motor power 370W

Absorbed Current 3A

Motor revolutions 1400 r/min

Motor thermal protection 120

Ambient temperature 20

C to

Maximum gate weight 1000kg

Maximum gate travel resistance 1 KgF

Duty cycle 60 cycles per hour

Linear speed (Max) 12m/min

2. Installation

2.1 Cable requirements.

A Intercom cable. As per manufacturer's spec.

B Safety infra red beams transmitter cable (0,5mm x 2)

Safety infra red beams receiver cable (0,5mm x 4)

D outesy light cables 220Vac (1,5mm x 3)

E Earth spike cable (2,5mm x 1)

F Electrical supply 220Vac (2,5mm x 3)

G Loop detector feeder (1,5mm x 1 looped)

HIntercom cable. (As per manufacturer's spec.

plus 0,5mm x 2 for push button trigger)

2.2 Installation and adjustment.

2.2.2 Installing the rack. (Ensure the rack tracks straight and true across the pinion gear. Where

necessary make use of feathering spacers between the rack and gate fascia to compensate for

bowed gates).

1 to 2mm spacing

View of rack tracking across

pinion. Ensure the teeth of both

the rack and pinion are parallel

to avoid binding.

Position the base plate

between 30 and 4 mm away

from the fascia of the gate.

NB! Take care when

determining the entry point for

your cabling.

Before installing the limit actuators on the rack, the gearbox must be released into manual mode.

1. Move the gate into the full CLOSED POSITION. Attach the RED MAGNETIC ACTUATOR to the

rack, within 10 – 20mm of the operator and inline with the pickup. (If the control card is

powered up, the closed limit LED must be off with the magnet in place)

2. Move the gate to the full OPEN POSITION. Attach the BLUE MAGNETIC ACTUATOR to the

rack, within 10 – 20mm of the operator and inline with the pick up. (If the control card is

powered up, the closed limit LED must be off with magnet in place)

NB! PHYSICAL STOPPERS MUST BE INSTALLED AT BOTH THE OPEN AND CLOSED POSITION!

THESE MUST BE SUFFICIENT TO STOP THE GATE.

To maneuver the gate by hand (manual

mode).

1. Slide the cover to the left as shown

here. Then insert the release key

supplied and turn fully clockwise.

2. To change back to automatic

mode (re-engaged) insert release

key and turn fully anti-clockwise.

3. When re-engaging the gearbox

always gently pull or push the gate

until a click is heard. Never push the

gate vigorously. This must be done

before triggering the motor to run.

Use self drilling tech screws supplied to mount the

limit brackets

3. Control card.

Trans ormer

1 P1 Set run time

2 P2 Set auto-close time

3 S1 Remote transmitter programming

button

4 LED 1 Set transmitter LED

5 LED 2 Running state LED

6 LED 3 Open limit LED

7 LED 4 lose limit LED

8 LED 5 Power LED

9 VR1 Adjust load sensing for crawl speed

10 VR2 Adjust load sensing for running speed

11 J3 Antenna terminals

12 J4 Load sensing. DO NOT REMOVE!

(ON = Active)

13 F1 Transformer fuse (2A)

14 F2 Motor fuse (10A)

15 S4 Function choice dipswitches

3.2 Motor wiring.

3.3 SETTING THE RUN TIME.

After installing and completing the wiring, (Swap motor wires L1 and L2 if motor runs in the wrong

direction).

1. Power up

2. Press and hold P1 for 3 sec.

a. Gate will begin running OPEN

b. On reaching the OPEN (Blue) limit the gate will begin running CLOSED

c. On reaching the CLOSED (Red) limit the run time programming is complete.

3.4 SETTING THE AUTO-CLOSE TIME (NB! This only programs the required time. Remember to activate

auto-close option by selecting Dipswitch 1 ON to activate Auto-close).

1. When the operator is not running, press and hold P2 for 3 sec.

2. LED 2 will illuminate indicating the timer has commenced,

3. At required auto-close time press and release P2 once again.

4. LED 2 will extinguish.

. The auto-close time is set.

3.5 ADJUSTING THE OBSTRUCTION SENSITIVITY

(J4) OBSTRUCTION LOAD SENSING! DO NOT REMOVE THIS JUMPER FROM THE ON POSITION.

On - Obstruction load sensing is active. THIS JUMPER SHOULD ALWAYS BE ON!

Off - All obstruction sensing is de-activated.

THIS CAN RESULT IN SERIOUS PERSONAL OR EQUIPMENT DAMAGE IF LEFT IN THE OFF

POSITION!!!!!!

1. To make the unit more sensitive to obstructions in soft start/soft stop stages of travel, turn

VR1 anti-clockwise.

2. To ignore slight binding or heavier to start gates, turn VR1 clockwise.

3. To make the unit more sensitive to obstructions in the normal running speed stage of travel,

turn VR2 anti-clockwise.

4. To ignore slight binding or heavier to run gates, turn VR2 clockwise.

NB! The correct adjustment to the obstruction sensitivity is vital to the safety of the installation.

Failure to test and adjust this can cause physical harm and damage to both the system and the

user. (It is advisable to install Infra red safety beams as an added safety measure)

If the unit still responds as though it is encountering an obstruction even though there is no obvious

object in the way of the gate travel when the sensing adjustments have been adjusted to the full

clockwise positions, the gate is in poor running condition. Correct the gate travel first before

continuing.

Inhaltsverzeichnis

Andere Et Toröffner Handbücher

Et DRIVE 1000 Bedienungsanleitung

Beliebte Toröffner Handbücher anderer Marken

Elite

Elite CSW200UL Bedienungsanleitung

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Chamberlain

Chamberlain MotorLift HC280ML Bedienungsanleitung

SOMFY

SOMFY Dexxo RTS Pro Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung