ETC QuickTouch Preset Handheld Bedienungsanleitung

ETC User Guide

QuickTouch Preset Handheld

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000

Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

8063M1210-1.52 Rev A Released 2020-07

Overview

This user guide provides information on how to use the QuickTouch Preset Handheld controller. There

are multiple types of users that can log in to the QuickTouch Preset Handheld controller. Each user

type has their own purpose and the user interface responds based on who logs in. You can identify the

type of user for your login by the Group designation when you select your user during login.

Use the table below to identify your user type and the actions that you can perform from each screen:

User Group Manual screen Presets screen Panel

Presets screen Settings screen

Emergency Manual move N/A N/A N/A

User

•

Manual move

•

Target move

•

Trim move

N/A N/A N/A

Preset Operator Go button to run Load preset N/A N/A

Operator

•

Manual move

•

Target move

•

Trim move

•

Load preset

•

Copy preset N/A N/A

Power User

•

Manual move

•

Target move

•

Trim move

•

Set trims

•

Set attached

load

•

Lock a motor

•

Advanced

config

•

Create

preset

•

Load preset

•

Edit preset

•

Copy preset

•

Delete

preset

•

Set as simple

•

Configure

OSC

N/A N/A

Panel Preset

Operator N/A N/A Run preset N/A

Panel User

•

Manual move

•

Target move

•

Trim move

N/A Run preset N/A

Admin N/A N/A N/A

•

Configure

display

•

Manage users

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 2 of 15 ETC

Warnings and Notifications

The operation of ETC Rigging™ equipment requires responsible use and specific training. Only

authorized, trained personnel should operate this rigging system. Unauthorized use, alteration, or

use for situations other than those for which it was designed may cause damage to the equipment,

other property damage, or injury to persons, potentially of a severe nature. All safety precautions

must be observed and adhered to at all times.

Read and obey the following warning statements to ensure safe and consistent use of your ETC

Rigging system.

WARNING: ETC Rigging systems must not be operated by a user until

installation and configuration have been completed by an ETC trained and

approved technician. Only ETC trained and approved technicians are authorized

to operate equipment during the installation and configuration process.

WARNING: Only properly trained and authorized persons shall operate ETC

Rigging systems.

WARNING: Improper operation may cause serious injury or death.

AVERTISSEMENT : Un fonctionnement incorrect peut provoquer des blessures

graves, voire mortelles.

WARNING: When using the ETC Rigging system, the user must have an

unobstructed view of the entire lineset and its attached load. If the user’s view

is obstructed, a second person (spotter) MUST be used to assist the operator at

all times. The spotter must have an unobstructed view of all moving

components and be able to maintain clear communication with the operator at

all times.

If a problem arises while a hoist is moving (such as a mechanical issue or

interference from other objects) stop movement immediately by releasing all

dead-man and "Go" buttons or by using the Emergency Stop button. If a spotter

sees a problem while a hoist is moving, the spotter must signal the user to stop

movement immediately.

WARNING: Devices under control of the ETC Rigging system must only be

used to move a maximum load equal to or less than its rated capacity.

Overloading the device may result in damage to the system, other property

damage, serious injury, or death.

AVERTISSEMENT : Les appareils sous le contrôle du système ETC doivent

uniquement être utilisés pour déplacer une charge maximale équivalente ou

inférieure à sa capacité nominale. Une surcharge de l'appareil peut entraîner

l'endommagement du système et d'autres biens, des blessures graves, voire la

mort.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 3 of 15 ETC

WARNING: Disconnect power before servicing this equipment.

AVERTISSEMENT : Déconnectez l'alimentation avant d'effectuer l'entretien

de cet équipement.

WARNING: The Working Load Limit (WLL) of any device is the maximum load

capacity that a user may apply to that device or system.

All ETC Rigging hoists have a Working Load Limit. This is identified on the

product label on the back of the hoist and on the batten label. This limit is not

the same for all hoists; be sure to check the Working Load Limit for all hoists in

your system. Prodigy Working Load Limits include a design-safety factor.

If you cannot find a Working Load Limit for any device under the control of the

ETC Rigging system, do not operate and contact your ETC Rigging installer.

NEVER exceed the Working Load Limit for any hoist.

WARNING: Do not exceed point load, Uniform Distributed Load (UDL), or

Working Load Limit (WLL) for any line set. See label on batten for POINT, UDL,

and WLL. Point, distributed, and working load limits may be different for each

device.

Do not suspend persons from the device or any of its components. Do not ride

on the batten.

Stop use of the system immediately if unusual noises are heard or unusual

smells are detected during operation. Contact a qualified ETC Rigging inspector

before resuming use.

In the event of an Emergency Stop (E-stop) cease use of the system, identify

who engaged the E-stop and why, and resolve the issue before restarting the

system.

Never lock or jam the operating buttons in the depressed (“on”) position. These

hold-down buttons must be operated by a competent person at all times. Log

out or remove the enable key of this rigging controller when a competent or

qualified person is not present.

Use a remote unit when the load is obscured from this operator position or have

someone observe the load while it is moving. Never leave the controller when a

hoist is in motion.

Prior to servicing the system, disconnect and lock out/tag out power (according

to NFPA Standard 70E) to any relevant components.

Always inspect and test the ETC Rigging system before each use.

Have certified ETC Rigging inspector perform regular inspection and

maintenance as dictated by the system installer, ETC's specifications, and

warranty agreements. The system must be inspected annually by a qualified

ETC Rigging inspector.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 4 of 15 ETC

Hardware

Touchscreen

Joystick

Deadman trigger

E-stop button

The QuickTouch Preset Handheld controller is

controlled using the following hardware features:

Touchscreen: Provides selection and configuration

options from the available screens.

E-stop button: Used to stop all movement in the

system when necessary.

Joystick: Provides a switch to control the velocity

of manual moves and the speed of target moves.

Deadman trigger: Closes the Deadman circuit

and, when depressed, allows for motor movement.

To log in to your controller, press Login from the

main screen. When the User Login dialog appears,

select the appropriate user login from the list. This

causes the Enter Pin Code dialog to appear. Enter

your user code and press Ok to log in.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 5 of 15 ETC

Manual

The Manual screen contains rows of channels on the top of the screen and configuration and

movement options on the bottom of the screen. The right and left sides of the screen have ENABLE

and VELOCITY indicator bars, respectively. The ENABLE bar illuminates when the Deadman trigger

is held down, indicating that the Deadman circuit is enabled and motors are ready for movement.

The VELOCITY bar is separated into blue (upper) and green (lower) halves. When pressing the

joystick in the up direction, the VELOCITYbar indicates the rate of movement in the blue area.

Likewise, pressing the joystick in the down direction indicates the rate of movement in the green

area.

Move Motors Manually

To move a motor manually, perform the following steps:

1. Select the channel or channels that you want to move.

2. Press and hold the Deadman trigger button. The ENABLE bar on the left side of the screen

illuminates.

3. Push the joystick in the up or down direction to move the selected motors.

4. Release the joystick and Deadman trigger when the motor reaches the intended destination.

Perform Target Moves

To perform a target move follow these steps:

1. Select one or more channels that you want to move to a specific target and then press the

editable Target field in the properties area.

2. In the Edit Target Position dialog that appears, enter the target destination and press Ok.

3. Press and hold the Deadman trigger to move to the target destination.

Note:

You can use the joystick to affect the rate of movement during a target move.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 6 of 15 ETC

Move Channels Using Trims

To move a moter using trims, perform the following steps:

1. Select the channel you want to move.

2. Click one of the trim buttons from the properties area to select the trim as your destination.

Note that the trim value is now displayed in the Target field.

3. Press and hold the Deadman trigger to move to the target destination.

Note:

You can use the joystick to affect the rate of movement during a trim move.

Set Channel Trims

You can set trims for you channels from the trim fields (Low Trim, Trim 1, Trim 2, High Trim) or from

the Trims tab in the Advanced dialog. When you select a trim from either workspace, the Edit trim

dialog appears and lets you set or edit a trim. You can also designate the Low and High trims as

limits if you want.

Set Attached Load Position

Setting your attached load position allows you to have the position readout indicate the bottom of

the attached load (i.e. bottom of the scenery) as opposed to the actual batten position. This allows

you to move a motor to 0'0" so that the scenery touches the stage and the batten remains at the

specifed elevation above the stage.

Perform the following steps to set an attached load:

1. Manually move the motor so that your attached load (i.e. scenery) rests at the lowest desired

position .

2. With the channel still selected, press the Load Attached button to open the Scenery Bottom

Position dialog.

3. Enter the position of the bottom of your load.

•

If the load is physically touching the stage, enter 0'0"

•

If the load is floating, enter the measured distance between the stage and the bottom of

the load

4. Press Ok.

Any channel that has a load attached configured displays a horizontal bar below the channel

position. For example, the following image shows the attached load position is set to 40' 0" for

channel 1.

Lock Motors

The "Lock" button can be found in the lower left part of a channel's properties area and can be

toggled between on and off for that channel. Press "Lock" to lock the selected channel and prevent

it from moving in any way. Press Lock again to unlock the channel.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 7 of 15 ETC

Advanced Configuration

You can open the Advanced dialog for any channel, from which the following tabs are available

with their respective functions.

•

Trims: Allows you to set trims for the motor

•

Load: Provides load information for your motor

•

Speed: Provides speed information for your motor

•

Status: Provides system status and history

•

Statistic: Provides statistical information

•

Diagnostic: Provides diagnostic information

Load Profiling

It is highly recommended that you enable load profiling for your motors. This feature allows you to

record a normal profile of what the load should be at any point in the full range of travel, in both

directions. Load profiling then monitors the load during movement and stops movement when

unexpected load conditions occur.

To record these load profiles and subsequently enable load profiling:

1. Select a channel and press the Advanced button.

2. Select the Load tab and press the Learn button.

•

For standard loads (i.e. scenery or non-electric loads), press the Save button.

•

For loads that change during travel, press the Record button.

Record the up and down profiles for the load

Save the profiles when you are satisfied

Close the Learn Load dialog

3. From the Load tab, you can now select the Enable Profiling button (outlined in gold when

selected).

4. You can also change the sensitivity setting per motor, with Maximum having the lowest

tolerance for deviance from the load profile and Low having the greatest tolerance.

Speed Configuration

You can also set the maximum speed of a motor. To set this speed, select a channel and press the

Advanced button. Select the Speed tab and press on the Max Speed field. In the dialog that

appears, enter the maximum speed at which you would like the motor to run.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 8 of 15 ETC

Presets

The Presets screen contains the same rows of channels on the top of the screen and configuration

options for presets on the bottom of the screen. Note that there may be some system presets that

are locked for editing. These can only be created or modified by a system installer.

Create Presets

Perform the following steps to create a preset:

1. Press "New". The New Preset dialog box opens. The first available preset number will be

automatically filled for you (starting with 1).

2. If a different preset number is desired, select the number field to change the number. The

"Edit Preset Number" dialog box will open and a numeric keypad allows you to enter a new

number.

3. If you wish to edit the name of the preset, select the preset name field. The onscreen

keyboard will open and you may edit the name of the preset and press Ok.

4. Press "Create". The new preset will be created and will appear in the preset display in the

properties area.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 9 of 15 ETC

Add Preset Content

Once a preset has been created, you can begin to add content to it in the Presets Screen.

Note:

It is recommended that you use trims when building presets, rather than specific

positions. Doing so will offer a much faster way to update presets. Trims represent a

universal way to update a motor position throughout all references. If a desired position

changes (for example, due to soft goods stretching), trim-based presets can be updated by

altering a single referenced trim position. Whereas with specified positions, all presets must

be updated manually.

To add preset content:

1. Make sure the desired preset is selected in the preset display. A selected preset is outlined in

gold.

2. Select a channel that you want to be in the preset. A position dialog box will open.

3. Enter the desired preset position for the motor for this preset.

•

You can reference a trim position by selecting from the four available trims or by pressing

"Trims" to see other trims recorded for the selected channel.

•

You can press "Current" to store the current position of the channel.

•

You can enter a specified position by selecting the position field. The "Edit Preset

Position" keypad opens. Enter a position on the numeric keypad and press "Ok".

4. Once the desired position appears in the position field, press "Ok" to close the motor position

dialog. The selected position will appear in the channel icon and the channel will remain

selected, indicating that it is currently stored as part of the preset.

5. Repeat steps 1-4 for any other channels you want to be included in the preset.

Note:

Preset content is stored automatically. You do not need to save a preset once it has

been created, nor after content has been updated.

Load a Preset

To load a preset, simply select the preset from the list and press the Load button. This takes you

directly to the Manual tab where you can press the Deadman trigger to run the preset.

Edit Presets

To edit a preset, select the preset you want to edit and perform the following actions:

•

Add a channel: Select the channel to add and set the desired preset motor position.

•

Remove a channel: Select the channel to open the position dialog and then press Remove.

•

Edit motor position: Select the channel to open the position dialog and then change the

desired motor position.

ETC User Guide

QuickTouch Preset Handheld

QuickTouch Preset Handheld Page 10 of 15 ETC

Copying Presets

You can copy any existing preset into a new or existing preset.

Copy to a new preset

To copy a preset to a new preset:

1. Select the desired preset from the preset display in the properties area of the preset screen.

2. Press "Copy". The "Copy Preset" dialog will open and the next unused preset number will

automatically be proposed.

3. If you want to copy to a different preset number, select the preset number field and enter the

desired preset number when the numeric keypad appears and press "Ok."

4. If you want to change the name of the preset, select the preset name field and enter the

desired name when the touchscreen keyboard appears and then press "Ok."

5. Press "Create" to copy the existing preset to the newly created one.

Note:

When you copy a simple preset, the newly created preset is also designated as a

simple preset. Conversely, when you copy a system preset, the new preset is not

designated as a system preset.

Copy to an existing preset

To overwrite an existing preset with a copied preset:

CAUTION:

Copying a preset into an existing preset will overwrite any content

in the existing preset entirely. A confirmation dialog will open if you attempt to

overwrite an existing preset.

Overwriting an existing preset that is referenced in the cue stack may severely

modify the look of your show. If you do so, it is vitally important to double check

and most likely re-program the cue stack.

CAUTION:

You are about to delete preset content that cannot be recovered.

1. Select the desired preset from the preset display in the properties area of the preset screen.

2. Press "Copy". The "Copy Preset" dialog will open and the next unused preset number will

automatically be proposed.

3. Select the preset number field. When the numeric keypad appears, enter the number of the

preset you wish to overwrite with the copy and press "Ok."

4. If you want to change the name of the preset, select the preset name field and enter the

desired name when the touchscreen keyboard appears and then press "Ok."

5. Press "Create." A confirmation dialog will open asking you to verify that you want to

overwrite the preset with the copy.

•

Press "No" to abort the copy. You will be returned to the "Copy Preset" dialog to enter a

different number.

•

Press "Yes" to overwrite the preset with the copied content.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Controller Handbücher

ETC

ETC Echoflex ELED1-BUN Bedienungsanleitung

ETC

ETC echoflex ELED1 Bedienungsanleitung

ETC

ETC ION Bedienungsanleitung

ETC

ETC ALiEn2 Bedienungsanleitung

ETC

ETC Expression Konfigurationshandbuch

ETC

ETC Element Bedienungsanleitung

ETC

ETC DMX DEBC-1 Bedienungsanleitung

ETC

ETC Unison Foundry Bedienungsanleitung

ETC

ETC Foundation Rigging Controller Installations- und Betriebshandbuch

ETC

ETC QuickTouch Preset Bedienungsanleitung

ETC

ETC ArcSystem Pro D4 Series Bedienungsanleitung

ETC

ETC echoflex ElahoTouch Bedienungsanleitung

ETC

ETC P-ACP Merkblatt

ETC

ETC ArcSystem Navis 100 Bedienungsanleitung

ETC

ETC echoflex ELEDR Bedienungsanleitung

ETC

ETC Echoflex ELED1H Bedienungsanleitung

ETC

ETC echoflex ELED1 Bedienungsanleitung

ETC

ETC F-Drive W1 Series Bedienungsanleitung

ETC

ETC QuickTouch Preset Bedienungsanleitung

ETC

ETC QuickTouch+ Mk2 Bedienungsanleitung

ETC

ETC DEBC Bedienungsanleitung

ETC

ETC PENKO Flex Bedienungsanleitung

ETC

ETC Echoflex ELED3 Bedienungsanleitung

ETC

ETC Echo Inspire Station Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch