ETC Echoflex ELED1H Bedienungsanleitung

Page 1ELED1H Installaon Guide

Installaon Guide

ELED1H Fixture Controller

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

• CAUTION - This equipment has more than

one power supply connection point. To reduce the

risk of electric shock disconnect both the branch

circuit-breakers or fuses and emergency power

supplies before servicing.

• CAUTION – Risk of Electric shock hazard. The

controller uses high voltage and should only be in-

stalled by qualied personnel in accordance with

National Electrical Code and any local regulations.

• CAUTION - To avoid electrical overload, total

connected load should not exceed output rating.

• This product is suitable for use in dry locations

where the ambient temperature is -5°C to +50°C.

• Do not use outdoors.

• Do not mount near gas or electric heaters

• Equipment should be mounted in locations

and at heights where it will not be subjected to

SAVE

THESE INSTRUCTIONS

Page 2 ELED1H Installaon Guide

tampering by unauthorized personnel.

• The use of accessory equipment not

recommended by the manufacturer may cause an

unsafe condition.

• Do not use this equipment for other than its in-

tended use.

• Servicing should be performed by qualied ser-

vice personnel.

• Pollution Degree:2.

Page 3ELED1H Installaon Guide

Overview

This guide covers the LED Fixture Controller, model number ELED1H-AU with

input voltage of 240-347VAC. The ELED1H is equipped with a 902 MHz

radio. The box contents includes the controller and installation guide.

A programming guide with detailed features of the controller is available for

download on www.echoexsolutions.com.

The controller uses wireless technology to monitor any room’s environment

and provides dimming and/or switching control of an LED xture.

The controller includes Simple Tap™ technology which allows installers and

facility operators to manage conguration settings without any tools.

Preparing To Install The Controller

The controller should be mounted in locations and at heights where it will

not be subjected to tampering by unauthorized personnel. The controller is

mounted using the conduit nipple for mounting the controller to electrical

junction boxes or panels. You will require hand tools and supplies (not

provided) to install the controller.

• Screwdrivers, pliers, wire cutters, wire insulation stripping tool

• Appropriately sized wire nuts

• Small cable ties

Scan QR code for link to programming guide

Page 4 ELED1H Installaon Guide

Installing the Controller

For best results mount the controller on the outside of the electrical box either

directly at the electrical load or before the load in the circuit.

Review these instructions completely before installing the controller.

1. Locate the circuit breaker panel and terminate power to the circuit.

2. Remove all face plates and other hardware from the junction box so

you can access the high voltage wires.

3. Mount the controller to the exterior of the junction box or panel with

the ½” threaded nipple.

4. Refer to the wiring diagram to connect the controller to line power,

neutral and load wires. Use wire nuts on all connections and

individually cap any bare wires (except orange antenna wire).

5. Connect the gray and purple wires to the driver or ballast’s dimming

interface (optional).

6. Replace the electrical box faceplate.

7. Restore power to the circuit.

8. If the controller was pre-commissioned you can use one of the pre-

linked devices to test the controller operation. If the controller was not

pre-commissioned by the factory, refer to the section of this guide

titled Linking the First Switch. Use this switch to verify the controller

functionality.

Wiring Diagram

ELED1H-AU

LED Fixture Controller

Power

LED

Clear

Button

Learn

Button

Learn

LED

Max. Switching Load

20A@240 -277VAC,

Electronic Ballast or LED Driver

16A@347VAC,

Electronic Ballast or LED Driver

Max. Dimming Load

100 mA sinking

Antenna (orange)

Do not cut or cap

Black - Line, 240-347VAC

@50/60 Hz

500 mW max

White - Neutral

Red - Load, 240-347VAC

Purple - Dimming 0-10V

Gray - Dimming COM

LED Driver

Max. Impulse Voltage: 4000V

Internal Relay: Type 1.C

Dimming output is Class 1 circuit

Independently Mounted Control for

Panel Mount/Surface Mount

iNote: Always follow applicable NEC and local electrical code

requirements when installing and powering the controller.

iNote: The Micro USB port is for factory use only. Do not attach

cables or accessories to this port

The use of accessory equipment not recommended by the manufacturer

may cause an unsafe condition. Do not use this equipment for other than

its intended use. Do not use outdoors.

Page 5ELED1H Installaon Guide

Electrical Terminations

The controller has an external orange antenna wire. Do not cut, cap or

connect this wire.

Power to the controller is connected between the White (Neutral) and the

Black (240-347 VAC) Line power. The Class 1 power limited dimming lines

(violet and gray wires) can be used to provide 0-10V control of a dimming

ballast or LED driver. Use only UL approved wire when making connections

to the controller, see table below.

Controller's Wire Details

Connection Color Specification

Load Red 14AWG, 600V

Neutral White 14AWG 600V

Line 240-347VAC Black 14AWG 600V

Dimming 0-10V Purple 18AWG 600V

Dimming GND Gray 18AWG 600V

Wiring Diagrams - For Use in Emergency Fixtures

ELED1H-AU

LED Fixture Controller

Power

LED

Clear

Button

Learn

Button

Learn

LED

ELED1H-AU

LED Fixture Controller

Power

LED

Clear

Button

Learn

Button

Learn

LED

Normal Hot

Normal Neutral

Emergency Hot

Emergency Neutral

Normal Control Sense

Normal/

Emergency

Load

ELED1H

Load Control

Dimming +Dimming -

LED Driver Hot

LED Driver Neutral

LED Driver

UL924 Emergency

Bypass Relay

with appropriate

voltage rang

Normal Hot

Normal Neutral

LED Driver

LED

Emmier

Board

Baery

Backup

Dimming +Dimming -

LED +LED -

LED +

LED -

ELED1H

Load Control

LED Driver

Hot

Page 6 ELED1H Installaon Guide

Linking the First Switch

Use this method to link the rst switch. Use the learn button to link additional

devices.

1. If the controller already has a sensor linked, press the TEACH button on

the linked sensor and proceed to step 2 within 60 seconds.

2. Click the wireless switch paddle ON three times, OFF three times and

ON three times sequentially within 5 seconds. The relay will toggle and

the red POWER LED will begin a repeating blinking pattern to indicate

the linked switch, see the section on LED blink codes.

LEARN button

The LEARN button is used to link switches or sensors to the controller.

1. Press the button marked LEARN for a half second. In link mode the

LEARN LED will stay ON and the POWER LED will toggle every two

seconds.

2. When linking a wall switch, press the switch paddle ON three times.

If linking a sensor, press the sensor’s TEACH or LINK button, refer to

the sensor’s documentation. The POWER LED will remain lit for four

seconds while it links the new device. It will resume toggling allowing

you to link another device up to a total of twenty devices.

3. To exit link mode, press and release the LEARN button on the controller.

iNote:Linking a switch or sensor that is already linked to a controller,

will remove or unlink it from the controller.

iNote: Link mode will time out after no activity in thirty seconds.

CLEAR button

Using the CLEAR button can reload the controller to the factory pre-

commissioned settings with linked devices OR it can load the factory default

parameters and remove all linked devices.

• To return the controller to the factory pre-commissioned state, press

the CLEAR button until the POWER and LEARN LEDs start blinking,

approximately 5 seconds. Release the button and the POWER LED will

begin blinking indicating the factory commissioned pre-linked devices.

• To completely clear the controller returning it to factory default settings

removing all linked devices, press the CLEAR button until the POWER

and LEARN LEDs come on solid, about 15 seconds, then release. The

POWER LED will stay ON solid indicating the factory default state.

Page 7ELED1H Installaon Guide

LED Blink Codes and Operation

The tables below describe the LED activity and associated mode of the

controller.

If the controller was factory pre-commissioned, upon power up it will

immediately begin blinking the red POWER LED based on the type and count

of linked devices. The type is indicated by long blinks followed by short blinks

counting the number of devices linked. This pattern will repeat after a short

pause.

The table below describes the number of LED blinks for each device type.

POWER LED Blink Codes

Factory Default ON Solid

switch(es) 1 long blink followed by short blinks counting switches

occupancy sensor(s) 2 long blinks followed by short blinks counting sensors

photo sensor(s) 3 long blinks followed by short blinks counting sensor

(typical max 1)

central command 4 long blinks followed by short blinks counting devices

demand response 5 long blinks followed by short blinks counting devices

Operang Mode and LED Acvity

Mode Red LEARN LED Red POWER LED Relay/Light

link mode ON toggle toggle

storing ID ON ON 4 seconds ON 4 seconds

clearing ID ON OFF 4 seconds OFF 4 seconds

factory default ON 1 second ON solid ON

Page 8 ELED1H Installaon Guide

Lisngs & Regulatory Statements

UL Listed Component

Certied UL Standard 924

Certied UL Standard 60730

Certied CAN/CSA Std E60730

UL 2043 Plenum rated

California Energy Commission Title 24 - CEC

Washington State Energy Code - WSEC

ANSI / ASHRAE / IES Standard 90.1

International Energy Conservation Code - IECC

New York City Energy Conservation Code - NYCECC

FCC Part 15.231 Contains FCC ID: SZV-STM300U

IC RSS-210FCC Part 15.231 Contains FCC ID: SZV-STM300U

The enclosed device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(i.) this device may not cause harmful interference and

(ii.) this device must accept any interference received, including

interference that may cause undesired operation.

Echoﬂex Solutions

38924 Queens Way, Unit #1, Squamish, BC, V8B 0K8, Canada n+1 778-733-0111

echoﬂexsolutions.com n8DC-5973-1.0 nDocument Part # 8189M21-5973-1 Rev A n12/20

Product information and specications subject to change without notice

Inhaltsverzeichnis

Andere ETC Controller Handbücher

ETC

ETC Unison Foundry Bedienungsanleitung

ETC

ETC DEBC Bedienungsanleitung

ETC

ETC QuickTouch+ Mk2 Bedienungsanleitung

ETC

ETC Element Bedienungsanleitung

ETC

ETC Echo Inspire Station Betriebsanleitung

ETC

ETC EA07 Bedienungsanleitung

ETC

ETC echoflex ELED1 Bedienungsanleitung

ETC

ETC Echoflex ELED2 Bedienungsanleitung

ETC

ETC QuickTouch Preset Bedienungsanleitung

ETC

ETC Echoflex ELED2 Bedienungsanleitung

ETC

ETC ArcSystem Navis 100 Bedienungsanleitung

ETC

ETC ArcSystem Pro D4 Series Bedienungsanleitung

ETC

ETC Unison Aero Bedienungsanleitung

ETC

ETC echoflex ELEDR Bedienungsanleitung

ETC

ETC echoflex ElahoTouch Bedienungsanleitung

ETC

ETC Echoflex Elaho Inspire Station Betriebsanleitung

ETC

ETC DMX DEBC-1 Bedienungsanleitung

ETC

ETC PENKO Flex Bedienungsanleitung

ETC

ETC Unison Aero Relay Controller Bedienungsanleitung

ETC

ETC QuickTouch Bedienungsanleitung

ETC

ETC Unison Foundry Relay Controller Bedienungsanleitung

ETC

ETC Foundation HD Bedienungsanleitung

ETC

ETC Foundation Rigging Controller Installations- und Betriebshandbuch

ETC

ETC F-Drive W1 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch