ETC Source 4WRD Bedienungsanleitung

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

Corpora te He a dqua rte rs Middleton, WI, USA +1 608 831 4116

London, UK +44 (0)20 8896 1000 Holzk irc hen, DE +49 (80 24) 47 00-0

Rome , IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 P aris, FR +33 1 4243 3535

We b etcconnect.com Support support.etcconnect.com

Product information and specifications subject to change. ETC intends this document

to be provided in its entirety. Trademark and patent info:etcconnect.com/ip

7068M1310-1.0.0 Rev A Released 2020-09

Introduction

The Source 4WRD Color is a replacement for a standard Source Four burner

assembly. It converts the HPL source to an RGBA (red, green, blue, and amber)

LED and provides a significant reduction in power consumption. The Source

4WRD Color uses DMX dimming and requires power from a non-dimmable

source. When not using DMX, you can use any of the 12presets or

5sequences on the Source 4WRD Color.

For complete information, download the Installation and User

Manual at etcconnect.com, or view online help on your

smartphone or tablet by scanning this code.

What's in the Box

•

Source 4WRD Color retrofit

•

Threaded post (see

Install the Source 4WRD Color Retrofit on page3

)

•

Diffusion (required—see

Install Diffusion on Reflector on page5

)

Safety

The Source 4WRD Color fixture is intended for professional use only. Read

the entire manual before using this equipment.

WARNING: Note the following safety warnings before use:

•

Do not mount the fixture on or near a flammable surface.

•

Do not use this fixture with a damaged power lead. If the

power lead (cord set) is damaged, it must be replaced.

•

Mount and support the fixture only by the primary

suspension holes in the yoke.

•

Suspend the fixture from a suitable structure using only

hardware rated for the weight of the fixture.

•

In addition to primary suspension, attach a safety cable to

the fixture housing. An appropriate attachment point

(hole) is provided in the protruding tab on the fixture

housing.

•

Disconnect the unit from power and DMX and allow the

fixture to cool before removing or installing accessories,

and before all cleaning and maintenance.

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

WARNING: Note the following safety warnings before use:

•

The Source 4WRD Color is not user serviceable. Field

modification of the Source 4WRD Color will void your ETC

warranty.

•

Do not use the fixture below 5°C (41°F).

•

Minimum storage temperature is 5°C (41°F). When the

fixture has been stored or transported in cold

temperatures, allow it to warm to room temperature for

a minimum of 1hour before applying power. Applying

power to a cold fixture will cause damage to the fixture

and void the ETCwarranty.

•

Do not use this fixture if a glass lens is deeply scratched or

cracked. Damaged lenses must be replaced.

•

To prevent wiring damage, or abrasion, do not expose

wiring to edges of sheet metal or other sharp objects.

•

Use the fixture in dry locations only, where humidity does

not exceed 90 percent (non-condensing). These fixtures

are not intended for outdoor use.

Retrofit the Fixture

WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Installing the

Source 4WRD Color retrofit kit requires knowledge of luminaire

electrical systems. If you are not qualified, do not attempt

installation. Contact a qualified electrician.

Note:

THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A

LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE

DETERMINED BY AUTHORITIES HAVING JURISDICTION.

Wire the Power Connector

If you ordered a Source 4WRD Color retrofit without a power connector, wire

the connector in accordance with all national and local electrical codes:

•

Brown = Live

•

Blue = Neutral

•

Green/Yellow = Protective earth

Source 4WRD Color (CE) Page 2 of 8 ETC

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

Remove Incandescent Lamp Housing

1. Unplug the Source Four incandescent fixture and place it on a flat,

stable surface.

2. Loosen the brass thumb screw located above the beam adjustment

knob. The lamp housing is now loose.

3. Slide the lamp housing away from the fixture body and locate the

screw that secures the earth bond wire to the fixture body. Loosen and

remove the screw and accompanying washer to free the earth bond

wire.

4. Remove the lamp housing from the fixture body.

Install the Source 4WRD Color Retrofit

WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Install this kit only

onto luminaires that have the construction features and

dimensions shown in the images in this document and where the

input rating of the retrofit kit does not exceed the input rating

of the luminaire.

WARNING: Do not make or alter any open holes in an enclosure

of wiring or electrical components during kit installation.

CAUTION:

Do not touch or clean LED emitters with anything

other than oil-free canned air.

Tools required:

•

Adjustable wrench

•

#2 Phillips screwdriver

Source 4WRD Color (CE) Page 3 of 8 ETC

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

1. Use oil-free canned air to clean the LED emitters before you install the

retrofit. Do not touch the LEDemitters.

2. With the fixture resting securely on a flat surface, attach the supplied

threaded post to the back end of the fixture body. Use an adjustable

wrench to tighten the threaded post one-quarter turn past finger

tight.

3. Secure the earth bond wire to the fixture body using the provided

screw and washer.

4. Gently slide the Source 4WRD Color onto the fixture body and

threaded post while guiding the LED tower into the lamp housing

hole, as shown in the following image. Take care to prevent contact

between the LEDs and the reflector.

Insert threaded

post here

Tighten

screw

Z-adjustment

knob

Source Four

fixture body

Lamp

housing

hole

Secure earth

bond wire

5. Use a #2 Phillips screwdriver to tighten the screw located on the back

end of the Source 4WRD Color, directly above the Z-adjustment knob.

6. Pull gently to verify secure attachment.

7. Set the Z-adjustment using the Z-adjustment knob. See

Set the Z-

adjustment on page8

Source 4WRD Color (CE) Page 4 of 8 ETC

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

Install Diffusion on Reflector

When you use the Source 4WRD Color with a Source Four fixture body, you

must install the diffusion provided with the Source 4WRD Color on the

output end of the reflector.

WARNING: Do not use the diffusion with a Source Four HPL

lamp. Using the diffusion with a Source Four HPL lamp can result

in damage to the diffusion and the fixture body.

Fold corners x4

Shiny side

facing up

With the shiny side of the diffusion

facing up, fold the four tabbed corners

of the diffusion along the perforated

lines.

2. Remove the lens tube and shutter

barrel from the fixture in order to

access the reflector housing.

3. Insert the diffusion into the reflector housing with the dull side of the

diffusion facing the lamp and the shiny side facing out.

4. Ensure that the tabbed corners are snug under the reflector bracket

wings.

Tabbed corner fits

under reflector

bracket wings

5. Replace and secure the shutter barrel and lens tube.

Source 4WRD Color (CE) Page 5 of 8 ETC

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

Install the Fixture

Attach Hanging Clamp and Safety Cable

The hanging clamp attaches the fixture to the mounting pipe andallows you

to adjust the position of the mounted fixture. ETCrecommends using 1.5in

schedule 40 pipe.

Tightly fasten the hanging clamp to the yoke, and then connect the safety

cable.

Connect Cables

WARNING: Do not use or store the Source 4WRD Color fixture

below 5°C (41°F). When the fixture has been stored or

transported in cold temperatures, allow it to warm to room

temperature for a minimum of 1 hour before applying power.

Applying power to a cold fixture will cause damage to the fixture

and void ETC warranty.

1. Connect one RJ45 data cable for data-in and one for data-thru, as

needed. Use the strain relief at the bottom of the fixture to support the

data cables.

•

To order an RJ45-to-female XLR adapter, use ETC part number

W6538.

•

To order an RJ45-to-male XLR adapter, use ETC part number

W6539.

2. If this is the last fixture in the line, terminate the fixture with a

120Ohm resistor. Please contact your ETC customer service

representative to purchase ETC part number N4086.

3. Connect the fixture to a non-dimmable power source.

DMXDimming

•

When using DMX over Cat5, use Cat5e or better.

•

Cable distance for full DMX daisy chain must not exceed 300m

(1000ft).

•

Up to 32 fixtures can be connected together into a daisy chain.

•

The fixture cannot be controlled via Ethernet protocols and should not

be directly connected to an Ethernet system.

Source 4WRD Color (CE) Page 6 of 8 ETC

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

Configure the Fixture

Up and down

navigation buttons

User interface

Use the up and down navigation buttons

to configure the fixture.

Set the DMXAddress

1. Press any button to wake the

display. The display shows the

DMX address.

2. Use the Up and Down buttons to

select the DMX address for the

fixture.

Play Presets and Sequences

The fixture has twelve factory-configured

presets and five factory-configured sequences. When you play a preset or

sequence on a fixture:

•

The same preset number or sequence number plays on any connected

fixtures that are not receiving DMX.

•

If you power down the fixture, the preset or sequence resumes when

you power it on again.

1. Press the Up button and Down button simultaneously to activate the

Presets/Sequences menu. The last active preset or sequence plays

automatically. (If DMX data is present, the current preset or sequence

plays in the background and DMX data continues to take priority.)

2. Press the Up button or Down button as needed to scroll through the

available presets and sequences.

3. To stop the selected preset or sequence, press the Up button and

Down button simultaneously. The display will revert to show the DMX

start address.

Source 4WRD Color (CE) Page 7 of 8 ETC

ETC Quick Guide

Source 4WRD Color (CE) Version 1.0.0

Set the Z-adjustment

Use the Z-adjustment knob located on the rear of the fixture to adjust the

field of the LED light for specific applications.

1. Turn on the fixture and aim it at a flat surface.

2. Slide the fixture barrel toward or away from the Source 4WRD Color to

create a hard-edged beam of light.

3. Turn the knob toward PEAK or FLAT until you achieve the desired field.

Ideal beam of

uniform light

Adjust toward PEAK to

blend overlapped beams

Adjust toward FLAT to

improve sharp focus

Z-adjustment knob

Note:

The Source 4WRD PAR or PARNel Fixture Body optics are

optimized for PEAKfocus. When using the Source 4WRD Color in a

Source 4WRD PAR or PARNel Fixture Body, turn the Z-adjustment

knob toward PEAK until the knob becomes loose, and then tighten

the Z-adjustment knob an additional quarter turn. This sets the LED

light source into the appropriate position within the fixture.

Clean the Fixture

CAUTION:

Do not touch or clean LED emitters with anything

other than oil-free canned air.

Fan and

fin stack

•

Use oil-free canned air to clean the

LED emitters prior to installation and

prior to storage.

•

Use oil-free canned air to clean the fan

and fin stack as part of regular fixture

maintenance.

Source 4WRD Color (CE) Page 8 of 8 ETC

Andere Handbücher für Source 4WRD

Inhaltsverzeichnis

Andere ETC DJ-Equipment Handbücher

ETC

ETC S4WRDCII Bedienungsanleitung

ETC

ETC Irideon FPZ Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC ColorSource Spot V 1.0 Bedienungsanleitung

ETC

ETC ColorSource Fresnel V Bedienungsanleitung

ETC

ETC Desire series Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC ColorSource Spot jr v2.0 Bedienungsanleitung

ETC

ETC Source Four PAR Bedienungsanleitung

ETC

ETC Releve Spot Bedienungsanleitung

ETC

ETC Source Four jr Bedienungsanleitung

ETC

ETC Prodigy FlyPipe Studio Bedienungsanleitung

ETC

ETC IRIDEON AR500 Bedienungsanleitung

ETC

ETC Desire D22 Bedienungsanleitung

ETC

ETC Source Four XT HID Zoom Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Source Four PARN Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC F-Drive R12 Series Bedienungsanleitung

ETC

ETC High End Systems SolaWash 1000 Bedienungsanleitung

ETC

ETC Congo jr Master Playback Wing Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung