ETC Source Four jr Bedienungsanleitung

ETC User Manual

Source Four®jr / jr Zoom

Corporate Headquarters



Middleton, Wisconsin, USA



Tel +608 831 4116

Service (Americas)



[email protected]

London, UK



Tel +44 (0)20 8896 1000



Service: (UK) [email protected]

Rome, IT



Tel +39 (06) 32 111 683



Service: (UK) [email protected]

Holzkirchen, DE



Tel +49 (80 24) 47 00-0



Service: (DE) [email protected]

Hong Kong



Tel +852 2799 1220



Service: (Asia) [email protected]

Web: etcconnect.com



Product information and

specifications subject to change.



ETC intends this document to be provided in its entirety.

7062M1001



Rev D



Released 2016-11



Production dates: September 2004–present

Basic Assembly

WARNING:

Please note the following safety warnings before use:

• Do not mount the fixture on or near combustible

surfaces.

• Do not operate the fixture without a lens installed.

• Always hang the fixture with the colour frame

retaining clip in the locked position.

Lamp

housing

C-clamp mounting

Barrel

Drop-in

iris slot

cover

Pattern

holder

slot

Gel frame

holder

Zoom rear focus knob

Beam focus knob

(Zoom front focus)

Yoke

Yoke locking knob

Color

frame

retaining

gel clip

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 2 of 12 ETC

Fixture information

HPL lamp table

CAUTION:

The Source Four jr is rated for 575W maximum lamp. Do

not use lamps other than the HPL in Source Four fixtures.

Use of lamps other than HPL or greater than 575W will

void your warranty.

Lamp code Watts Volts Initial Lumen Color temp. Average

rated life

HPL 550/77* 550 77 16,170 3,250° 300 hours

HPL 550/77X* 550 77 12,160 3,050° 2000 hours

HPL 575/115 575 115 16,520 3,250°K 300 hours

HPL 575/115X 575 115 12,360 3,050°K 2000 hours

HPL 375/115 375 115 10,540 3,250°K 300 hours

HPL 375/115X 375 115 8,000 3,050°K 1000 hours

HPL 575/120 575 120 16,520 3,250°K 300 hours

HPL 575/120X 575 120 12,360 3,050°K 2000 hours

HPL 575/230 575 230 14,900 3,200°K 400 hours

HPL 575/230X 575 230 11,780 3,050°K 1500 hours

HPL 375/230X 375 230 7,250 3,000°K 1000 hours

HPL 575/240 575 240 14,900 3,050°K 400 hours

HPL 575/240X 575 240 11,780 3,050°K 1500 hours

HPL 375/240X 375 240 7,250 3,000°K 1000 hours

* To be used with ETC Dimmer Doubler™

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 3 of 12 ETC

Color frame holder

The color frame holder is

equipped with a spring-loaded

retaining clip that prevents

color frames and accessories

from falling out.

1: Release the retaining clip by pushing it sideways while gently pulling

backwards.

2: Insert the color frame.

3: Lock the retaining clip by pushing sideways while gently pushing

forward.

WARNING:

Make sure all color frame accessories are locked in

position with the retaining clip before hanging the

Source Four.

Note:

The performance of saturated colors may be less than

desirable in any theatrical lighting fixture. For best

results, always use high-quality color media rated for

high-temperature use.

ETC’s optional Conical Gel Extender (part number

7060A1048) will provide maximum color media life. Gel

Extenders are not recommended for 70° and 90° lens

tubes due to the extremely wide-angle beam.

A variety of heat shield products is also available from

many color media manufacturers. Follow the

manufacturer’s instructions for the use of these

products.

Retaining

clip

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 4 of 12 ETC

Replacing the HPL lamp

A lamp must be installed before you use the fixture.

1: Disconnect power to the fixture before installing the lamp.

2: Loosen the knurled bolt on the back of the lamp housing and pull the

housing out.

3: Holding by the base, remove the HPL lamp from its box.

Note:

Verify that the HPL lamp you intend to install is suitable

for your facility’s voltage; 115-, 120-, 230-, and 240-volt

HPL lamps are available. See HPL lamp table on page 2.

Operating HPL lamps above their rated voltage reduces

lamp life and can cause premature lamp failure.

WARNING:

Let the lamp cool before replacing.

CAUTION:

Use caution when installing or replacing any lamp.

When installing/replacing lamp, be sure to point the

lamp away from your face and away from others before

inserting it firmly into the assembly.

This may prevent injuries if the lamp should break.

Note:

To avoid premature lamp failure, do not touch the lamp

glass. If you do, clean it carefully with isopropyl alcohol

and a clean lint-free cloth. Allow to dry before

operation.

INCORRECT CORRECT

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 5 of 12 ETC

4: Align the flat sides of the lamp base with the retention brackets on

either side of the socket as shown below.

5: Push down on the lamp base until the lamp seats firmly. When

properly installed, the top of the lamp’s base will be even with the top

edges of the retention brackets.

6: Press lamp retaining clip across lamp base to secure.

7: Reinstall the lamp housing by aligning the bolt hole and tightening the

knurled bolt.

Adjustments

Centering lamp and adjusting the field

The two concentric knobs located on

the lamp housing allow you to align

the lamp and adjust its field. See figure

at right. The outer knob centers the

lamp within the reflector. The inner

knob adjusts the lamp’s field.

1: Turn on the fixture and aim it at

a flat surface. Adjust the barrel

to create a hard edge.

2: Unlock and loosen the outer

knob by turning it

counterclockwise.

3: Gently move the outer knob

from side to side and up and

down until the lamp is centered

within the reflector.

CAUTION:

Improperly installed lamps cause premature lamp failure

and socket problems.

HPL lamp

Lamp retention clip

Knurled bolt

Lamp housing

Lamp retention

brackets

Outer Knob: Lamp

center adjustment

Inner Knob:

Peak/flat field

adjustment

Rear lamp

housing

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 6 of 12 ETC

4: Once the lamp is centered, turn the outer knob clockwise to lock it in

place.

5: Finally, turn the inner knob either clockwise or counterclockwise to

achieve an optimum flat field. See figure below.

Focusing the beam

On a fixed field angle Source Four jr with a 26°, 36° or 50° lens, adjust the

lens single beam focus knob to focus the edge of the beam. On a Source Four

jr Zoom, adjust the position of both lens beam focus knobs to set the beam’s

spread and to focus the edge of the beam. The Zoom lens provides a range

from 25° to 50°.

1: Loosen the beam focus

knob(s) on the underside of

the barrel as shown at right.

2: Slide the lens(es) forward or

backward to achieve the

desired beam edge.

3: Once the fixture is focused,

tighten the beam focus

knob(s).

Flat field:

Best adjustment

Hot spot:

Lamp pulled out

too far

Field with hole:

Lamp pushed in

too far

Beam focus knobs

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 7 of 12 ETC

Shaping the beam

The beam can be shaped using the shutters, a

pattern, or an optional drop-in iris.

Pattern Projection

The pattern holder slot is on the top side of the barrel

and in front of the shutters. It accommodates an

M-size pattern holder (see figure at right). The

pattern holder handle can be bent away from the

shutter handle to keep it from interfering with the

action of the shutter handle.

Use an optional donut in the accessory holder to

enhance pattern projection. Donut diameter range

should be 2.5” to 2.75”.

Drop-In Iris Slot

The drop-in iris slot is located on the top of the barrel and in front of the

pattern holder slot. It accommodates either a drop-in iris or a motorized

pattern device. When the slot is not in use, a small sheet metal cover secured

with two Phillips screws prevents light leakage (see figure below).

1: Use a Phillips screwdriver to loosen the screws on the drop-in iris slot

cover. Do not remove screws.

2: Slide the cover completely forward to expose the slot.

3: Insert the iris with the flat side toward the shutters and make sure the

iris handle extends from the slot.

4: Slide the slot cover back toward the shutters until it meets the iris

handle. Leave enough space to move the iris handle.

5: Secure the drop-in iris slot cover by tightening the screws.

M-Size

Pattern holder

Drop-in

iris slot

Iris

Pattern holder slot

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 8 of 12 ETC

Adjusting the C-clamp

The C-clamp attaches the

fixture to the mounting pipe

and allows you to adjust the

position of the fixture once it

is mounted (see figure at

right).

1: Tightly fasten the

C-clamp to the yoke

with the provided

yoke bolt and lock

washer.

2: Place the C-clamp on

mounting pipe, and then tighten the pipe bolt to secure it.

3: Loosen the C-clamp pan screw and rotate the yoke to the desired

position.

4: Tighten the pan screw to lock the fixture.

CAUTION:

Tighten C-clamp pipe bolt to 15–20 ft./lbs.

(approximately finger tight plus up to one-quarter

turn). Do not exceed 25 ft./lbs. Do not use excessive

force.

Tighten the yoke pivot bolt to 5–10 ft./lbs.

(approximately finger tight plus up to one-eighth turn).

Do not exceed 15 ft./lbs. Do not use excessive force.

ET C

C-clamp

Pipe bolt

Pan screw

Yoke bolt and

lockwasher

Yoke

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 9 of 12 ETC

Adjusting the yoke position

The Source Four jr / jr Zoom provides multi-positioning capabilities within its

yoke for overall fixture height and angle.

Setting the fixture height within the yoke

The fixture is equipped with a two-position yoke for modifying the overall

height in which the fixture is mounted (see figure below). To change the

height position, perform the following steps.

1: Remove the yoke locking knobs, washers, and hex bolts from either

side of the fixture.

2: Raise or lower the fixture to the desired position within the yoke.

3: Reinstall the yoke’s hex bolts, washers, and locking knobs.

4: Tighten the yoke knobs to secure in position.

Setting the angle within

the yoke

1: Loosen the yoke locking

knobs (see figure at

right). Do not remove

them.

2: Tilt the fixture to the

desired position.

3: Tighten the yoke locking

knobs to secure in

position.

Low clearance positionGeneral use position

Yoke

locking knob

Yoke locking knob

ETC User Manual

Source Four jr / jr Zoom

Source Four jr / jr Zoom Page 10 of 12 ETC

Lens and Reflector

Switching lens assemblies

Follow these procedures to replace

a fixed field lens with Zoom lens.

1: Loosen the screw at the

front of the baffle. See

figure at right.

2: Pull the light baffle out of

the barrel.

3: Remove the beam focus

knob from the bottom of

the barrel and slide the lens assembly from the barrel.

4: Slide the Zoom lens rear assembly into the barrel and install its beam

focus knob.

5: Slide the Zoom lens front assembly into the barrel and install its beam

focus knob.

6: Reinstall the light baffle and secure it with the retaining screw.

Note:

Reverse steps 1–6 to replace Zoom lens with a standard

lens.

Lens tray

Light baffle and

retaining screw

Andere Handbücher für Source Four jr

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC DJ-Equipment Handbücher

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC RoadHog 4 Bedienungsanleitung

ETC

ETC High End Systems SolaPix 19 Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC ColorSource Spot V 1.0 Bedienungsanleitung

ETC

ETC Source Four Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Desire series Bedienungsanleitung

ETC

ETC High End Systems SHOWGUN Handbuch

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Source Four XT HID Zoom Grid Louver Bedienungsanleitung

ETC

ETC ColorSource PAR Bedienungsanleitung

ETC

ETC Source Four PARN Bedienungsanleitung

ETC

ETC ColorSource Bedienungsanleitung

ETC

ETC ColorSource Spot Bedienungsanleitung

ETC

ETC Congo jr Master Playback Wing Bedienungsanleitung

ETC

ETC ColorSource Fresnel V Bedienungsanleitung

ETC

ETC Releve Spot Bedienungsanleitung

ETC

ETC Irideon FPZ Bedienungsanleitung

ETC

ETC Source Four PAR Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung