ETC Unison ERn2-W Bedienungsanleitung

Part Number: 7180M2100 Rev: C

Released: 2020-06

ERn Wall-mount Enclosure

Installation Manual

To view a list of ETC trademarks and patents, go to

etcconnect.com/ip

. All other trademarks, both

marked and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents i

Table of Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . . .1

ERn External Processing Rack. . . . . . . . . . . . . . . . . . . . .1

ERn2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

ERn4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

ERn Modules and Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Contacting ETC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Prepare for Installation . . . . . . . . . . . . . . . .6

Unpack and Inspect . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Main Circuit Breaker Protection . . . . . . . . . . . . . . . . . .6

Maximum Current Input . . . . . . . . . . . . . . . . . . . . . . . .6

Where to Install the Enclosure. . . . . . . . . . . . . . . . . . . .6

Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Rack Dimensions and Weights. . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation Environment Requirements . . . . . . . . . . . . . . . . . .7

Wire Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Wire Routing and Specification. . . . . . . . . . . . . . . . . . . . . . . . .8

Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Control Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Data Types and Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Install Rack Enclosures. . . . . . . . . . . . . . . .10

Install the Rack Enclosure. . . . . . . . . . . . . . . . . . . . . . .10

Rough-in Conduit and Wiring . . . . . . . . . . . . . . . . . . .11

Remove Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Rough-in Line and Control Conduit and Wiring . . . . . . . . . .12

Terminate Wiring . . . . . . . . . . . . . . . . . . .13

Connect Line Power Wiring . . . . . . . . . . . . . . . . . . . . .13

Connect Control Wiring . . . . . . . . . . . . . . . . . . . . . . . .14

Connect ERn Right I/O Data Terminations . . . . . . . . . . . . . . .15

Connect ERn Left I/O Data Terminations . . . . . . . . . . . . . . . .18

Final Installation and Power Up . . . . . . . .21

Check Main Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Check Line Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Final Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Install Rack Options. . . . . . . . . . . . . . . . . .24

Rack Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

ii ERn Wall-mount Installation Manual

Install the RideThru Option (URTO) Kit. . . . . . . . . . . . . . . . . .24

Install the BatteryPack Option (UBPO) Kit . . . . . . . . . . . . . . .26

Install a Paradigm Repeater or Dual Repeater Module . . . . .28

Install Redundant Power Supply . . . . . . . . . . . . . . . . . . . . . . .31

Status Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Install the Ethernet Switch Module. . . . . . . . . . . . . . . . . . . . .32

Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Introduction 1

Introduction

Welcome to the installation manual for the Unison ERn External Control Enclosure. This

manual contains the procedures for safe and efficient installation of wall-mount ERn series

control enclosures, including wire termination and option kit installation.

ERn series enclosures provide Unison architectural control to distributed Unison, Sensor, or

other DMX512 systems. Used stand alone or in multi-processor network systems, the 

wall-mount ERn series offers elegant low-profile surface mounting, modular back-lit control

electronics, and the ultimate in architectural lighting control versatility.

ERn External Processing Rack

The ERn enclosure is available in two sizes, ERn2 (single processor) and ERn4 (dual processor),

The ERn is available in three single phase voltage options, 100-120, 230 CE, and 240 VAC to

meet your installation requirements. See the technical datasheet on the ETC website

etcconnect.com for a full listing of available models.

ERn2

The ERn2 enclosure supports a single Paradigm Architectural Control Processor (P-ACP) and

one Paradigm Station Power Module (P-SPM) or a blank module (ERn-BM). The accessory tray

in the bottom of the enclosure can be used for an additional accessory option including a 

5-port Ethernet Switch (ERn-NET) or a Redundant Rack Power Supply (ERn-RPS).

ERn4

The ERn4 enclosure supports up to two Paradigm Architectural Control Processors (P-ACP)

and two Paradigm Station Power Modules (P-SPM) or a Paradigm Repeater Module (P-REP).

Alternatively, the top two slots in the enclosure may be used for a Paradigm Dual Repeater

Module (P-DREP). The accessory tray in the bottom of the enclosure can be used for an

additional accessory option including a 5-port Ethernet Switch (ERn-NET) or a Redundant

Rack Power Supply (ERn-RPS).

2ERn Wall-mount Installation Manual

ERn Modules and Options

P-ACP

P-SPM

P-REP

P-DREP

ERn-NET

ERn-RPS

UBPO

URTO

ERn-BM

Model Part

Number Description Notes

P-ACP 7180A1001 Paradigm

Architectural Control

Processor

The P-ACP provides powerful and flexible control for

architectural and theatrical applications with integrated

networking for both NetConnect and LinkConnect networks.

• Supports up to 1024 control channels using industry

standard protocols.

• User interface remains accessible with the enclosure door

closed.

• Supports up to 62 Unison control stations over the

LinkConnect network with the use of Paradigm Station

Power and Repeater Modules.

• Supports up to 12 Paradigm Touchscreen Stations using

LinkConnect or NetConnect protocols.

• Provides two ports, one DMX universe each (512 addresses

each), individually switchable between input and output.

P-SPM 7182A1001 Paradigm Station

Power Module

The P-SPM supplies power for Unison control stations and

sensors over the LinkConnect network, up to 500 m

(1,640 feet).

• Supports up to 32 Unison control stations over

LinkConnect.

P-REP 7182A1003 Paradigm Station

Repeater Module

The P-REP extends the system station bus length by 500 m

(1,640 feet) and increases the possible station count by an

additional 30 stations and sensors. For use only in an ERn4

enclosure.

• For use in an ERn4 enclosure only.

• Supports up to 30 additional Unison control stations over

LinkConnect.

P-DREP 7182A1004 Paradigm Dual

Station Repeater

Module

The P-DREP extends the system station bus length by

1,000 m (3,280 feet) through two separate topology-free

segments, each supporting 500 m (1,640 feet).

• The dual repeater supports up to 30 additional Unison

control stations and sensors.

• For use in an ERn4 enclosure only.

Introduction 3

ERn-NET 7180A1400 ERn Ethernet Switch

Module

The ERn-NET module provides four ports of 802.3af

compliant Power over Ethernet (PoE) and one port for the P-

ACP.

• Not compatible with a rack-mount ERn enclosure.

• Not compatible with ERn4 230 VAC enclosures.

UBPO 7180A1411 Unison Battery Pack

Option Kit

The UBPO provides back-up power during power outages for

the P-ACP for up to 90 minutes for an ERn enclosure with

one P-ACP or up to 45 minutes for an ERn4 with two P-ACPs

installed.

• Not compatible with a rack-mount ERn enclosure.

URTO 7180A1410 Unison Ride Thru

Option Kit

The URTO kit provides power for one P-ACP in the host

enclosure for a limited time (minimum of 12 seconds) during

brief power outages or drop outs.

• If installed in an ERn4 enclosure, one URTO is required per

installed P-ACP.

ERn-BM 7180A1402 Blank Module The ERn-BM is required for any empty module space in the

ERn enclosure.

• Installs into the accessory option module slot of an ERn

enclosure.

ERn-RPS 7180A1401 ERn Redundant

Power Supply

The ERn-RPS provides an additional rack power supply that

powers the ERn enclosure if the primary rack power supply is

removed or fails.

• Tool-free installation into the accessory option slot of an

ERn enclosure.

• Not supported in ERn4 230 VAC enclosures. The

ERn4 230 VAC enclosure requires two rack power supplies

as standard.

Model Part

Number Description Notes

4ERn Wall-mount Installation Manual

Warnings and Notice Conventions

These symbols are used throughout this installation manual to alert you to danger or

important information:

Please email comments about this manual to: [email protected].

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION:

A Caution statement indicates situations where there may be undefined or

unwanted consequences of an action, potential for data loss or an equipment

problem.

WARNING: A Warning statement indicates situations where damage may occur, people

may be harmed, or there are serious or dangerous consequences of an action.

WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates situations where

there is a risk of electric shock.

Introduction 5

Contacting ETC

For questions about Unison rack system delivery, contact ETC Systems Group. For general

information, your most convenient resources are the references provided in this manual. To

search more widely try the ETC web site at etcconnect.com.

For technical questions about Unison rack systems, contact ETC Technical Services directly at

one of the offices listed below. Emergency service is available from all ETC offices outside of

normal business hours. When calling for assistance, please have the following information

handy:

• Your location and job name.

• A complete list of ETC equipment.

• A complete list of other installed products and components connected to the system you are

troubleshooting.

• DMX control source, if any

Americas United Kingdom

ETC, Inc. ETC Ltd - UK

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

[email protected] te[email protected]

Asia Germany

ETC Asia ETC GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong techserv-germany@etcconnect.com

+852 2799 1220

techserv-asia@etcconnect.com

France

ETC France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

[email protected]

6ERn Wall-mount Installation Manual

Chapter 1

Prepare for Installation

Unpack and Inspect

Before you begin installation, check your shipment and confirm it arrived complete and undamaged.

1: Check the shipping container for physical damage.

2: If you find damage, document it to help with a claim against your shipper.

3: Unpack your order and check the contents against the packing list to be sure your order is

complete.

4: If you discover a problem, call ETC Systems Group.

Main Circuit Breaker Protection

Before you begin installing the Unison external processing rack enclosure, make sure you have installed

a main circuit breaker cabinet or other readily accessible input power disconnect device in the same,

room or in close proximity to the installed ERn enclosure.

Maximum Current Input

The ERn enclosure draws a maximum current of 3.5 amps when fully populated. The maximum

allowable protection device rating is:

• 20A at 120 VAC

• 15A at 230/240 VAC

Where to Install the Enclosure

The Unison External Processing Enclosure (ERn) can be wall-mounted or rack-mounted depending on

the model ordered. For rack-mounted installation instructions see the

ERn Rack-mount Enclosure

Installation Manual

Install the ERn wall-mount enclosure on a load bearing wall that is located in an electrical closet or a

room with restricted public access. It is recommended that you install the rack at least 914.4 mm

(36 in) off the floor surface to ensure clear view of the P-ACP for programming and general operation.

WARNING: Circuits that are installed without an accessible power disconnect device

cannot be serviced or operated safely. Follow local codes and restrictions.

AVERTISSEMENT: Il est imprudent d'utiliser ou de réparer les circuits installés sans qu'un

dispositif de déconnexion de l'alimentation ne soit accessible.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Gehäuse Handbücher

ETC

ETC DRd6-12-120 Bedienungsanleitung

ETC

ETC Sensor+ SR+ Series Bedienungsanleitung

ETC

ETC 7180A1018 Bedienungsanleitung

ETC

ETC Unison AX Series Bedienungsanleitung

ETC

ETC OneTrack Backbone I-coupler Housing Bedienungsanleitung

ETC

ETC 7180A1018 Bedienungsanleitung

ETC

ETC OneTrack Backbone T-coupler Housing Bedienungsanleitung

ETC

ETC OneTrack Backbone End Feed Housing Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung