ETC Source Four Mini LED Bedienungsanleitung

Source Four Mini LED

F-Drive

User Manual

Part Number: 7063M2130 Rev C

Released: 2023-12

To view a list of ETCtrademarks and patents, go to etccon-

nect.com/ip. All other trademarks, both marked and not marked,

are the property of their respective owners.

For a complete list of all third-party licenses that are fully incor-

porated herein to the extent required by each third-party license

terms and conditions, please visit etcconnect.com/licenses.

ETC intends this document, whether printed or electronic, to be

provided in its entirety.

Table of Contents

Source Four Mini LED (F-Drive) User Manual i

Overview 1

Safety 2

Canopy Luminaire 3

Installation 4

Install a Lens Tube 4

Luminaire Wiring 4

Install Canopy Luminaire 6

Connect Portable Luminaire 8

Power Up Procedure 8

Identify 8

Focus and Setup 9

Adjust the Tilt 9

Focus the Beam 9

Shape the Beam 9

Use the Color Frame Holder 10

Cleaning 11

Specifications and Reference 12

FCC Compliance 12

ii Source Four Mini LED (F-Drive) User Manual

Source Four Mini LED (F-Drive) User Manual 1

Overview

This guide provides installation instructions for Source Four Mini LED lumin-

aires. They are intended for use with the ETC F-Drive family of drivers and

accessories (including R12, W1, and B-Box) or other Class 2 or Low Voltage

Limited Energy (LVLE) power supplies (48 VDC maximum). Consult the spe-

cifications and installation manual for your driver to ensure compatibility.

This release of the Source Four Mini LED luminaire is compatible with the

R12 CC-150 output card or the W1 CC driver. Set the output channel for

the luminaire to 350 mA.

Canopy Portable

Note:

For the portable luminaire, use an M10 bolt to secure a

clamp (provided separately) to the luminaire.

For more information about compatible products, see the resources below,

which are available for download at etcconnect.com/Products/Power-Con-

trols/LED-Drivers/F-Drive/Documentation.aspx:

•

F-Drive Series R12 Installation Manual

•

F-Drive Series W1 Installation Manual

•

F-Drive R12 and W1 Wiring Reference Guide

•

F-Drive B-Box4 Installation Guide

The F-Drive System Design Tool is available at etccon-

nect.com/FDriveSysDesignTool.

You must install a lens tube before you use the Source Four Mini LED. There

are four lens tube sizes available: 19°, 26°, 36°, and 50°.

There are also canopy, track, and portable versions of the luminaire that are

not compatible with the F-Drive family of drivers and accessories. See the

luminaire datasheets at etcconnect.com for more information on Source

Four product options.

2 Source Four Mini LED (F-Drive) User Manual

Yoke

Pattern

holder slot

Shutter

barrel

Lens tube

Color frame

retainer clip

Color

frame

Safety cable

attachment point

Shutters x4

Beam

focus knob

Safety

WARNING: Note the following safety warnings before use:

• Use the luminaire in dry locations only, where humidity

does not exceed 90 percent (non-condensing).

• Do not mount the luminaire on or near a flammable

surface.

• Check that the accessory holder is locked before

mounting the luminaire.

• Do not operate the luminaire without a lens installed.

• Do not use this luminaire if a lens is deeply scratched or

cracked. You must replace a lens when it is damaged.

AVERTISSEMENT : Prendre connaissance des avertissements

de sécurité suivants avant toute utilisation :

• Ne pas installer le projecteur sur ou à côté d’une surface

inflammable.

• Vérifiez que le porte-accessoires est verrouillé avant de

monter le projecteur.

• N’utilisez pas le projecteur sans que la lentille soit

installée.

Source Four Mini LED (F-Drive) User Manual 3

IMPORTANT SAFEGUARDS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS

• Keep lamp away from materials that may burn.

• Do not touch hot lens, guard, or enclosure.

• Do not remain in light if skin feels warm.

• Do not look directly at lighted lamp.

• External temperature after 5 minutes of full-brightness operation:

50°C (122°F).

• External temperature when steady state is achieved: 67°C

(152.6°F).

SAVE THESE INSTRUCTIONS

Canopy Luminaire

WARNING: RISK OF ELECTRIC SHOCK! Power must be off

when you perform this procedure.

The luminaire must be installed by a qualified electrician in

accordance with all national and local electrical and con-

struction codes and regulations.

AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLÉCTRIQUE!

L'alimentation doit étre éteinte avant d'exécuter cette procé-

dure.

The luminaire must be installed at

least 0.1m (4.0in) away from all

lighted objects.

Le luminaire doit être installé à au

moins 0,1m (4,0po) de tout objet

éclairé.

General warning Avertissement général

This product should not be

discarded as unsorted waste but

must be sent to separate collection

facilities for recovery and recycling.

Ce produit ne doit pas être jeté avec

les déchets ménagers mais doit être

déposé dans une collecte de déchets

électroniques ou dans un point de

collecte.

This product meets the safety

requirements specified for Class III

according to IEC 60536.

Produit à Protection Classe III Très

basse tension conforme à la norme

IEC 60536.

The product input or output is

suitable for direct current only.

L’entrée et la sortie de ce produit

convient uniquement au courant

continu.

4 Source Four Mini LED (F-Drive) User Manual

Installation

Install a Lens Tube

You must install a lens tube before you use the Source Four Mini LED. There

are four lens tube sizes available: 19°, 26°, 36°, and 50°.

Lens Tube Description

4M19LT (-1, -5) 19° Source Four Mini Lens Tube Only Black (White, Silver)

4M26LT (-1, -5) 26° Source Four Mini Lens Tube Only Black (White, Silver)

4M36LT (-1, -5) 36° Source Four Mini Lens Tube Only Black (White, Silver)

4M50LT (-1, -5) 50° Source Four Mini Lens Tube Only Black (White, Silver)

1. Unscrew the beam focus knob from the loose lens tube.

2. Slide the lens tube into the shutter barrel.

3. Install the beam focus knob.

Beam focus knob

Luminaire Wiring

Luminaire power and data in and out cables terminate to RJ45 connectors.

Please note the following requirements for wiring:

• Use 0.25 mm2(23 AWG) or larger gauge conductors in Category-type

cable terminated to the T568B standard. Not all Cat5 or Cat6 cables

meet this gauge requirement.

• You can connect up to four luminaires along one run of cable when

using RJ45 output from a compatible output card or driver. The total

cable distance for each wiring run should not exceed 100 m (328 ft).

See the

F-Drive R12 and W1 Wiring Reference Guide

for more details.

Source Four Mini LED (F-Drive) User Manual 5

Select the Driver

CAUTION: F-Drive channels are not configured to the

proper current for this luminaire by default. You must con-

figure the channel on the driver to 350 mA. Connecting the

luminaire to a channel that is configured for more than 350

mA will shorten the life of the luminaire LEDs and may void

the luminaire warranty.

This release of the Source Four Mini LED luminaire is compatible with the

R12 CC-150 output card or the W1 CC driver. Set the output channel for

the luminaire to 350 mA.

For more information about compatible products, see the resources below,

which are available for download at etcconnect.com/Products/Power-Con-

trols/LED-Drivers/F-Drive/Documentation.aspx:

•

F-Drive Series R12 Installation Manual

•

F-Drive Series W1 Installation Manual

•

F-Drive R12 and W1 Wiring Reference Guide

•

F-Drive B-Box4 Installation Guide

The F-Drive System Design Tool is available at etccon-

nect.com/FDriveSysDesignTool.

RJ45 Pinout Information

In Port

Pin Description

1 - *

2,6 THRU 1**

3,7 THRU 2**

4,8 THRU 3**

5 + *

*Pins 1 and 5 receive power from the source or the previous luminaire in line.

**These pins pass through power to the next luminaires in line.

Out Port

Pin Description

1,5 THRU 1

2,6 THRU 2

3,7 THRU 3

4,8 No Connection

6 Source Four Mini LED (F-Drive) User Manual

Use of Third-Party Drivers with Daisy-Chained

Luminaires

Source Four Mini LED luminaires can be controlled by third-party Class 2 or

Low Voltage Limited Energy (LVLE) drivers that provide a maximum of

48VDC. To daisy-chain luminaires and still have independent channel func-

tionality, you must wire the first luminaire in the chain as described below.

(The RJ45 outputs on F-Drive natively support this wiring configuration.)

Configure the third-party drivers to a maximum of 350 mA.

Channel Input Pins for First Luminaire in

Daisy-Chain Description

(First luminaire)

1 Channel 1 -

5 Channel 1 +

(Second luminaire)

2 Channel 2 -

6 Channel 2 +

(Third luminaire)

3 Channel 3 -

7 Channel 3 +

(Fourth luminaire)

4 Channel 4 -

8 Channel 4 +

Install Canopy Luminaire

Note:

The canopy luminaire can be installed directly on 4in and

4-11/16in back boxes, or on back boxes with round cover plates.

The canopy luminaire cannot be installed on 1-gang back boxes or

trim rings.

Mounting

plate

Mounting

plate bolt

Safety

braid

Canopy

bolts

Mounting

plate bolts

Andere Handbücher für Source Four Mini LED

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC High End Systems SolaPix 19 Bedienungsanleitung

ETC

ETC Source Four Mini CE Bedienungsanleitung

ETC

ETC High End Systems SolaPix 7 Bedienungsanleitung

ETC

ETC D22 Desire series Bedienungsanleitung

ETC

ETC IRIDEON AR500 Bedienungsanleitung

ETC

ETC fos/4 Panel Pole-Operated Yoke Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Hog 4 Series Bedienungsanleitung

ETC

ETC Source Four MultiPAR Bedienungsanleitung

ETC

ETC Sensor3 Bedienungsanleitung

ETC

ETC fos/4 Panel Yoke Bedienungsanleitung

ETC

ETC source four fresnel Bedienungsanleitung

ETC

ETC Desire D22 Bedienungsanleitung

ETC

ETC Source Four HID PARNel Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC Desire D40XTI Bedienungsanleitung

ETC

ETC Source Four Revolution Scroller Cartridge Bedienungsanleitung

ETC

ETC Source Four LED 3 Series Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC microVision FX Bedienungsanleitung

ETC

ETC Source Four LED series Bedienungsanleitung

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC Lustr+ Bedienungsanleitung

ETC

ETC fos/4 Fresnel Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung