ETC Desire D22 Bedienungsanleitung

ETC Installation Guide

Desire®Series D22

Corporate Headquarters



Middleton, Wisconsin, USA



Tel +608 831 4116

Service (Americas)



[email protected]

London, UK



Tel +44 (0)20 8896 1000



Service: (UK) [email protected]

Rome, IT



Tel +39 (06) 32 111 683



Service: (UK) [email protected]

Holzkirchen, DE



Tel +49 (80 24) 47 00-0



Service: (DE) [email protected]

Hong Kong



Tel +852 2799 1220



Service: (Asia) [email protected]

Web: etcconnect.com



Product information and

specifications subject to change.



ETC intends this document to be provided in its entirety.

7411M2100



Rev D



Released 2016-12

Introduction

The Desire D22 is designed for indoor installations and has a rugged die-cast

enclosure, steel mounting yoke, and noise-free, fan-less operation.

The D22 can be pipe mounted with a C-clamp, canopy mounted, or track

mounted. Mounting accessories are available. Contact ETC Customer Service

for assistance; contact information is located at the bottom of this page.

For information about the operation of the D22 Desire Series, see the

Desire

Series by ETC D22, D40, D40XT, D60 User Manual

. ETC manuals are available

for download at etcconnect.com.

CAUTION:

Do not attempt to install or use a fixture until you read

and understand the installation instructions and safety

labels.

WARNING:

This fixture must be installed by a qualified electrician

in accordance with all national and local electrical and

construction codes and regulations.

Portable Canopy Mount Track Mount

ETC Installation Guide

Desire D22

Desire D22 Page 2 of 8 ETC

Specifications

Environment

Operates in ambient temperatures of 0°C to +40°C (32°F to 104°F).

Control

Portable

The Portable D22 is provided with 5-pin XLR connectors on the back for In

and Thru connection to a DMX/RDM control network.

Canopy Mount

The D22 Canopy Mount fixture is provided with one cable, which provides

power and data into the canopy.

A termination board is incorporated into the mounting plate for installation

onto a voltage-separated junction box (junction box provided by others,

voltage barrier provided by ETC) and provides termination for control wiring:

• Connection of the D22 data cable to a provided screw-down

connector, which is pre-wired at the factory. The connector is plugged

into the termination board. The braided shield is connected inside the

fixture and should not be connected in the canopy.

• Connection of DMX/RDM input from the control source. This

connection can be cable type Belden 9729 (or equivalent) to the

provided screw terminal. When using Cat5 (or equivalent) cable type

for DMX/RDM input, order a Cat5 termination kit from ETC (part

number 4100A1013). Cat5 termination instructions and an IDC

connector are provided with the termination kit.

• Connection of DMX/RDM thru to the next DMX device. This

connection may also be either Belden 9729 or Cat5. The connector is

not provided. Order the appropriate DMX termination kit for the cable

type used from ETC (Belden 9729: 4100A1012; Cat5: 4100A1013).

Termination instructions and the appropriate connector is provided

with the termination kit. Up to 32 DMX/RDM devices can be

daisy-chained together per data run.

Track Mount

The Track Mount fixture’s power and data connections are made through the

DataTrack™(EUTRAC®) MultiAdapter mounting adapter. No further wiring to

the fixture is required. See the track installation instructions for more

information.

CAUTION:

Risk of eye injury. Do not stare directly into the light.

Do not operate in proximity to flammable materials.

ETC Installation Guide

Desire D22

Desire D22 Page 3 of 8 ETC

Electrical

The Desire D22 Portable fixture has a permanently installed power cord with

3-prong Edison connector. Region-specific connectors are available. Contact

ETC for available options. The Canopy Mount fixture is provided with power

and data wired to the canopy and should be terminated in a voltage-

separated junction box (provided by others). The Track Mount fixture receives

power through its MultiAdapter, which connects to one of two circuits.

Power Requirements

The universal power supply accepts 100–240 VAC 50/60Hz.

WARNING:

Ensure the main power supply is off before installing or

wiring a fixture.

CAUTION:

Do not use a fixture for any voltage for which it is not

rated. Do not exceed the specified voltage and current

input for any fixture. Connecting the fixture to a voltage

outside the acceptable range may damage the unit and

will void the factory warranty.

Note:

The fixture must be grounded.

Application-appropriate electrical junction box with

cord grips is required. A voltage-separated junction box

is required. A RACO 232 series 4 x 2-1/8 inch deep

junction box is recommended. The junction box must

not interfere with fixture focusing.

The fixture is factory pre-wired. Opening the housing is

not required.

The fixture must be connected to a non-dimmable

power source. Dimming the unit will damage the fixture

and void the factory warranty.

Power Connections

Mains Europe North America

Line Brown Black

Neutral Blue White

Ground Green/Yellow Green

ETC Installation Guide

Desire D22

Desire D22 Page 4 of 8 ETC

Installation

Termination

The D22 Desire Series requires termination at the last fixture on a DMX/RDM

line with a 120-ohm resistor.

• The Portable fixture is self-terminated.

• The Track Mount fixture is terminated with a DataTrack DMX Term

Block (ETC part number 7066A1030).

• The Canopy Mount fixture is terminated on the Termination board

inside the canopy.

Canopy Mounting Plate and Termination Board

Termination

The Canopy Mount fixture is

terminated with the S1

switch on the Termination

board. Set the switch to the

ON position to terminate the

last fixture. All others on the

DMX/RDM line must be set to

OFF.

Termination

board

Power block

Mounting plate

Termination switch

D22 Data connector

ETC Installation Guide

Desire D22

Desire D22 Page 5 of 8 ETC

Installing the Canopy Mount Fixture

The Canopy Mount fixture is installed on to a RACO 232 series 4 x 2-1/8 inch

deep double junction box. The fixture is supplied with a divider to separate

the data network from the line voltage inside the junction box.

DMX/RDM Cable Installation

1: Terminate DMX/RDM input from the

control source to the junction box.

If using Belden 9729:

a: See the

DMX Cable Preparation

for Screw Termination Setup

Guide

for instructions to prepare

and terminate Belden 9729 for

DMX input cable to the screw

terminal connector.

b: Install the screw terminal

connector with wires terminated

to the DMX/RDM Input receptacle

on the termination board.

CAUTION:

Separate the line voltage from the data side in the

junction box. Install the voltage barrier provided by ETC.

Canopy

Installation hook

Junction box

(not provided)

Data/Voltage

divider

Mounting plate

assembly

From a DMX/RDM source

Data – (Black)

Data + (Red)

Belden 9729 (or equivalent) wire

termination to screw connector

4 to 8 = n/c

COM

ETC Installation Guide

Desire D22

Desire D22 Page 6 of 8 ETC

If using Category 5:

a: See the

Cat5 Cable Preparation for

IDC Termination Setup Guide

for

instructions to prepare and

terminate Category 5 for DMX/RDM

input cable to the insulation

displacement connector.

b: Install the IDC connector with wires

terminated to the DMX/RDM Input

receptacle on the termination board.

2: Optionally, terminate DMX/RDM thru

to the next device in the DMX data run.

Up to 32 DMX/RDM devices can be

daisy-chained together per data run. See

Control

page 2

a: See the specific termination setup guide for the type of cable used

(either Belden 9729 or Category 5) in the installation. Termination

kits are ordered separately.

b: Install the connector with wires terminated to the DMX/RDM Thru

receptacle on the termination board.

3: Terminate DMX/RDM data signal for the last DMX/RDM device in the

data run by setting the termination switch on the termination board to

ON. All other devices in the data run maintain the factory default

termination switch setting OFF. See

Termination

page 4

Canopy Mounting Plate Installation

1: Install the divider in the junction box

with the provided screw, separating

the power side from the data side.

2: Strip the supply power wires back

1/2 inch (13 mm).

3: Use a #2 Phillips screwdriver to

remove the two screws retaining the

canopy to the mounting plate.

4: Following the label on the mounting

plate, attach the supply power wires

to the power block on the mounting plate. See

Canopy Mounting

Plate and Termination Board

page 4

5: Attach the power supply ground wire to the mounting plate.

6: Plug in the input DMX/RDM connector (and thru DMX/RDM

connector, if used) to the appropriate location on the terminal board.

7: Attach the mounting plate to the junction box, ensuring the cables are

properly routed inside the box.

Data – (ORG)

Data + (W/ORG)

Cat5 (or equivalent) wire

termination to IDC connector

COM

BRN

GRN

W/GRN

BLU

W/BLU

ETC Installation Guide

Desire D22

Desire D22 Page 7 of 8 ETC

Canopy Fixture Installation

1: Strip the fixture’s power wires back

1/2 inch (13 mm).

2: Using the hole in the mounting

bracket, hang the canopy on the

installation hook.

3: Following the label on the

mounting plate, attach the power

wires to the power block.

4: Secure the fixture ground wire to

the mounting plate.

5: If the fixture is the last fixture on a

DMX/RDM line, terminate the fixture. See

Termination

page 4

6: Insert the DMX/RDM connector into the Terminal board.

7: To determine the alignment of the canopy, orientate the fixture to

where it will need to be focused.

8: Align the holes in the canopy with the mounting posts on the

mounting plate and using a #2 Phillips screwdriver, secure the canopy

to the mounting plate with the canopy screws.

9: Focus the fixture.

10: Tighten the canopy tension nut to set additional resistance for the

rotation of the fixture.

Installing the Portable Fixture

The C-clamp attaches the fixture to the

mounting pipe. The position of the fixture can

be adjusted once it is mounted. Tightly fasten

the C-clamp to the yoke with the provided yoke

bolt and lock washer.

1: Place the C-clamp on the mounting pipe,

and then tighten the pipe bolt to secure it.

2: Loop a safety cable over the pipe and

attach the ends to the safety cable loop

on the body of the fixture.

3: Loosen the C-clamp yoke bolt and rotate the yoke to the desired

position.

4: Tighten the bolt to lock the fixture.

CAUTION:

Do not overtighten the canopy tension nut.

Installation

hook and

bracket

Canopy

tension

nut

Safety

loop

ETC Installation Guide

Desire D22

Desire D22 Page 8 of 8 ETC

Installing the Track Fixture

1: Insert the DataTrack adapter into

the track. The adapter only fits

into the track one way with the

tabs nesting into the track’s

groove.

2: Rotate the locking mechanisms to

lock the adapter into place.

3: Use the circuit selection lock to

select circuit 1 or 2. The desired

circuit number should point

toward the center of the adaptor.

4: Focus the fixture.

Addressing

Fixture addresses must be set between 1 and 510. Each Desire fixture must be

considered a separate DMX device for the purpose of DMX line-loading

calculations.

No more than 32 DMX devices can be daisy-chained together on a single run.

For runs of fixtures totaling more than 32 DMX devices, a DMX splitter will

need to be used to split the DMX runs.

When using RDM with track fixtures, ETC recommends connecting no more

than 20 fixtures on a single run.

Initial Power Up

Control and configuration of the Desire D22 can be achieved over a

DMX/RDM control network, or directly from a connected computer running

appropriate software. When controlling the D22 directly from a PC, a

Gadget II Interface or DMX/RDM gateway is required.

CAUTION:

Tighten the C-clamp pipe bolt to about 18 inch lbs.

(Approximately finger tight plus up to one-quarter

turn.) Do not use excessive force.

WARNING:

When using the circuit selection lock, ensure the

selected circuit is a constant power circuit. Dialing into

a dimmable circuit may cause fixture damage that will

void the ETC warranty.

Andere Handbücher für Desire D22

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETC Beleuchtungsausrüstung Handbücher

ETC

ETC Source 4WRD Bedienungsanleitung

ETC

ETC Source Four LED series Bedienungsanleitung

ETC

ETC HIGH END SYSTEMS LONESTAR Bedienungsanleitung

ETC

ETC Source Four HID PARNel Bedienungsanleitung

ETC

ETC Source Four Zoom Bedienungsanleitung

ETC

ETC Sensor IQ DALI Control Option Card Bedienungsanleitung

ETC

ETC 3 Series Bedienungsanleitung

ETC

ETC Lustr+ Bedienungsanleitung

ETC

ETC Source Four Mini LED Bedienungsanleitung

ETC

ETC Sensor3 Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Source Four LED Series Bedienungsanleitung

ETC

ETC Acclaim 100 series Bedienungsanleitung

ETC

ETC Express 24/48 Bedienungsanleitung

ETC

ETC Irideon WLZ Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC fos/4 Series Bedienungsanleitung

ETC

ETC F-Drive W1 Series Bedienungsanleitung

ETC

ETC SolarFrame 750 Bedienungsanleitung

ETC

ETC source four fresnel Bedienungsanleitung

ETC

ETC ArcLamp System Bedienungsanleitung

ETC

ETC CE Source Four Bedienungsanleitung

ETC

ETC Expression 2.0 Bedienungsanleitung

ETC

ETC GDS BluesSystem Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung