EtherWAN EL1141 Series Bedienungsanleitung

W70G-EL1141Q1 Page 1

Installation Guide

EL1141 Series | Hardened Media Converter

1Unpacking

Open the carton and unpack the items. Your package

should include an EL1141 media converter and an AC

to DC power adaptor and cable

(optional). If items are missing or

damaged, notify your EtherWAN

representative.

Download the full manual at:

https://www.etherwan.com

2Select Installation Location

Installation is DIN rail-mount, or wall mount (in an

enclosure or industrial panel). Ensure that the power

source is within 6 feet (1.8 meters), and check that

there is adequate airflow. Operating temperature

range is -40to 75°C (-40 to 167°F).

3Connect Power

DC Terminal Block Power Inputs: There are two

10~48VDC power inputs that can be used to power

up this device.

Only one power input is required to run the media

converter, but with only one power connection the

FAULT LED indicator will light up to indicate

abnormality in the power redundancy system. The

media converter will work normally even if the fault

LED indicator lights up.

DC Jack Power input: 12VDC.

Terminal Block

DC Jack

Note: Use qualified power supply by SELV or

double insulation of UL 60950 or UL 61010-1 or UL

61010-2-201 standards.

Insert the DC input wires into the corresponding

terminals, and tighten the clamp screws to hold them

in place. Make sure that the plastic terminal block

connector prongs are plugged firmly into the terminal

block receptacles.

Power wiring information:

Use cable type - AWG (American Wire Gauge) 18-24

and the corresponding pin type cable terminals.

Use torque value 1.7 lb-in, do not use excessive force

when fixing wiring.

4Front Panel Reference

Description

PW1

12-48VDC

GND

Power Ground

PW2

12-48VDC

GND

Power Ground

Earth Ground

The relay contact opens if

Power 1 or Power 2 fails.

The relay contact opens if port

link fails (When Link Down

Detection is enabled).

Description

PW3

Power input 12VDC

The relay contact opens if

Power 1 or Power 2 fails.

The relay contact opens if port

link fails (When Link Down

Detection is enabled).

W70G-EL1141Q1 Page 2

Installation Guide

EL1141 Series | Hardened Media Converter

5LED Indicators

LEDs

State

Indication

FAULT

Steady

Power redundant system or ports function

abnormal

Off

Power redundant system and ports

function normally

PWR1

PWR2

PWR3

Steady

Power on

Off

Power off

100 (Mbps)

Steady

Connection at the speed of 100Mbps

Off

Connection at the speed of 10Mbps

LFPT

Steady

LFPT function enabled

Off

LFPT function disabled

LNK/ACT

Steady

Valid network connection established

Flashing

Transmitting or receiving data

Off

Neither valid network connection

established nor transmitting / receiving

data

FDX/COL

Steady

Connection in full duplex mode

Flashing

Collision occurred

Off

Connection in half-duplex mode

6DIP Switch Settings

Port, power and LFPT settings are made very simple by

means of DIP (Dual Inline Package) switches on the

bottom panel of the hardened media converter.

* LFPT=Link Fault Pass Through

Link-Fault-Pass-Through allows network operators to

stay aware of network connection status. If a link fails,

the function will disable the link on the other side,

therefore notifying the connected device of the link

failure.

If Force mode is enabled, the media converter must be

restarted in order for the new setting to take effect.

Pin 2 must be toggled to position 1 prior to speed and

duplex mode manual setting.

7Relay Output Alarm

The media converter is equipped with relay output

contacts on the terminal block for signaling of a

power or port failure. The relay output can be

connected to an alarm signaling device. Current is

1A @ 250VAC. Do not connect a power source to

the relay output.

8Other Information

DIN-Rail Assembly Startup, and Dismantling

▪Assembly: Place the device on the DIN rail from

above using the slot. Push the front of the device

toward the mounting surface until it audibly snaps

into place.

▪Startup: Connect the supply voltage to start up

the device via the terminal block.

▪Dismantling: Pull out the lower edge and then

remove the device from the DIN rail.

Manufacturer information:

EtherWAN Systems, Inc.

33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New

Taipei City, 221 Taiwan

No.

Disable LFPT*

Enable LFPT*

Enable auto

negotiation for TX

port

Enable forced mode

for TX port

TX port forced to

100Mbps

TX port forced to

10Mbps

TX port forced to

full duplex mode

TX port forced to half

duplex mode

FX port forced to full

duplex mode

FX port forced to half

duplex mode

Disable link down

alarm

Enable link down

alarm

The full product manual can be downloaded from:

www.etherwan.com

Andere EtherWAN Medienkonverter Handbücher

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL42011 Series Bedienungsanleitung

EtherWAN

EtherWAN EL900 Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EL1032T Series Bedienungsanleitung

EtherWAN

EtherWAN EL9100 Bedienungsanleitung

EtherWAN

EtherWAN EL9020 Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL50 Series Bedienungsanleitung

EtherWAN

EtherWAN EL2211 Bedienungsanleitung

EtherWAN

EtherWAN EL2326L Bedienungsanleitung

EtherWAN

EtherWAN EL2321 Bedienungsanleitung

EtherWAN

EtherWAN EL1033 Bedienungsanleitung

EtherWAN

EtherWAN EL2242 Series Bedienungsanleitung

EtherWAN

EtherWAN EL2242 Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL1032T Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1200R Bedienungsanleitung

EtherWAN

EtherWAN EL100T Bedienungsanleitung

EtherWAN

EtherWAN EL2242 Series Bedienungsanleitung

EtherWAN

EtherWAN EX42011 Bedienungsanleitung

EtherWAN

EtherWAN EMC400 Bedienungsanleitung

EtherWAN

EtherWAN EL2321 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung