EtherWAN EL900 Series Bedienungsanleitung

Hardened Media Converter

Quick Start Guide

This quick start guide describes how to install and use the hardened media

converter. This is the media converter of choice for harsh environments

constrained by space.

Physical Description

The Terminal Block and Power inputs

1. DC Terminal Block Power Inputs: There are two pairs of power inputs

can be used to power up this media converter. Redundant power

supplies function is supported. You need to have two power inputs

connected to run the media converter, but the FAULT LED indicator

will light up to remind that the power redundant system functions

abnormal in case either PWR1 or PWR2 is dead. Media Converter,

however, continues working normally even fault LED indicator lights

up.

2. DC JACK Power input: 12VDC.

Hardened Media Converter

The 10/100Base-TX and 100Base-FX Connectors

1. The 10/100Base-TX Connections

The following lists the pinouts of 10/100Base-T/TX ports.

Pin Regular Ports Uplink port

1 Input Receive Data + Output Transmit Data +

2 Input Receive Data - Output Transmit Data -

3 Output Transmit Data + Input Receive Data +

4 NC NC

5 NC NC

6 Output Transmit Data - Input Receive Data -

7 NC NC

8 NC NC

2. The 100Base-FX Connections

The fiber port pinouts: The Tx (transmit) port of device I is connected to the

Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx

(transmit) port of device II.

Hardened Media Converter

The Port Status LEDs

LEDs State Indication

Steady Power redundant system or port function abnormallyFAULT

Off Power redundant system and ports function normally

Steady Power on

PWR stands for POWER

PWR1

PWR2

Off Power off

Steady Connection at the speed of 100Mbps100 (Mbps)

Off Connection at the speed of 10Mbps

Steady LFPT function enabledLFP

Off LFPT function disabled

Steady Valid network connection established

LNK stands for LINK

Flashing Transmitting or receiving data

ACT stands for ACTIVITY

LNK/ACT

Off Neither valid network connection established nor transmitting/receiving data

Steady Connection in full duplex mode

FDX stands for FULL-DUPLEX

Flashing Collision occurred

COL stands for COLLISION

FDX/COL

Off Connection in half-duplex mode

Hardened Media Converter

Functional Description

yMeets NEMA TS1/TS2 Environmental requirements: temperature,

shock, and vibration for traffic control equipment.

yMeets IEC61000-6-2 EMC Generic Standard Immunity for industrial

environment.

ySupport 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,

full/half-duplex; Auto MDI/MDIX.

y100Base-FX: Multi mode SC or ST type; Single mode SC or ST type;

WDM Single mode SC type.

yOne DIP switch for configuring link-fault-pass-through, fixed speed,

full/half duplex, and link down alarm.

yAlarms for power and port link failure by relay output.

Relay contact rating with current 1A @ 30VDC, 0.5A @ 120VAC.

yOperating voltage and Max. current consumption: 0.76A @ 12VDC,

0.38A @ 24VDC, 0.19A @ 48VDC. Power consumption: 9.12W Max.

yPower Supply: Redundant DC Terminal Block power inputs or 12VDC

DC JACK with 100-240VAC external power supply.

y-40 to 75 (℃℃-40℉to 167℉) operating temperature range. Tested for

functional operation @ -40 to℃85 (℃-40℉to 185℉).

ySupports Din-rail, Panel, or Rack Mounting installation.

yUL1604 Class 1, Division 2 Classified for use in hazardous locations

(Applicable to versions with Terminal Block power option).

This equipment is suitable for use in Class I, Division 2,

Groups A, B, C and D OR non-hazardous locations only.

WARNING – EXPLOSION HAZARD – Do not disconnect

equipment unless power has been removed or the area is

known to be non-hazardous.

WARNING – EXPLOSION HAZARD – Substitution of

components may impair suitability for Class I, Division 2.

Assembly, Startup, and Dismantling

yAssembly: Place the media converter on the DIN rail from above using

the slot. Push the front of the media converter toward the mounting

surface until it audibly snaps into place.

yStartup: Connect the supply voltage to start up the media converter via

the terminal block (or DC JACK).

yDismantling: Pull out the lower edge and then remove the media

converter from the DIN rail.

Hardened Media Converter

Preface

This hardened media converter provides an affordable solution for rugged

and outdoor environment, transportation road-side cabinet, industrial floor

shop, multitenant dwellings or Fiber To The Home (FTTH) applications.

Capable of operating at temperature extremes of -40°C to +75°C, this is the

media converter of choice for harsh environments constrained by space.

Plug-and-Play Solution:

The hardened media converter is a plug-and-play media converter in

compact size. It doesn't have any complicated software to set up.

This manual describes how to install and use the hardened media converter

with the link-fault-pass-through function. The converter introduced here

provides one channel media conversion between 10/100Base-TX and

100Base-FX.

The converter fully complies with IEEE802.3 10Base-T and IEEE802.3u

100Base-TX/FX standards.

In this manual, you will find:

yProduct overview

yFeatures on the media converter

yIllustrative LED functions

yInstallation instructions

ySpecifications

Hardened Media Converter

Table of Contents

QUICK START GUIDE ..............................................................1

PHYSICAL DESCRIPTION...............................................1

FUNCTIONAL DESCRIPTION...........................................4

ASSEMBLY,STARTUP,AND DISMANTLING......................4

PREFACE...................................................................................6

TABLE OF CONTENTS ..............................................................7

INTRODUCTION ........................................................................8

PRODUCT OVERVIEW ...................................................8

PRODUCT FEATURES ...................................................8

PACKING LIST ..............................................................9

ONE-CHANNEL MEDIA CONVERTER .................................. 10

PORTS.......................................................................10

PORT SETTINGS.........................................................10

DIP SWITCH...............................................................10

FRONT PANEL &LEDS...............................................11

LINK-FAULT-PASS-THROUGH .....................................12

INSTALLATION ...................................................................... 13

SELECTING A SITE FOR THE EQUIPMENT .....................13

DIN RAIL MOUNTING..................................................13

CONNECTING TO POWER............................................14

SPECIFICATIONS ................................................................... 17

Hardened Media Converter

Introduction

The media converter provides one channel for media conversion between

10/100Base-TX and 100Base-FX with the link-fault-pass-through function.

This hardened fiber optic solution is perfectly fitted in the industrial

applications or rugged environment.

Product Overview

Product Features

yMeets NEMA TS1/TS2 Environmental requirements such as temperature,

shock, and vibration for traffic control equipment

yMeets IEC61000-6-2 EMC Generic Standard Immunity for industrial

environment

yUL1604 Class 1, Division 2 Classified for use in hazardous locations

(Applicable to versions with Terminal Block power option)

yOne-channel media conversion between 10/100Base-TX and

100Base-FX

yFiber media allows:

Multi-mode fiber using SC or ST connector

Single-mode fiber using SC or ST connector

Hardened Media Converter

WDM single-fiber (bi-direction) transceiver: Single-mode WDM

fiber using SC connector

A type: WDM single-fiber (bi-direction) transceiver transmits

with 1310nm wavelength and receives with 1550nm

wavelength

B type: WDM single-fiber (bi-direction) transceiver transmits

with 1550nm wavelength and receives with 1310nm

wavelength

yAuto negotiation of speed and duplex mode on TX port

yAuto MDIX on TX port

yOne DIP switch for configuring link-fault-pass-through, fixed speed,

full/half duplex, and link down alarm

y2048 MAC addresses, 768K bits buffer memory

yStore-and-forward mechanism

yNon-blocking full wire-speed forwarding rate

ySupport broadcast storm filtering

yBack-pressure & IEEE802.3x compliant flow control

yAlarms for power and port link failure by relay output

yRelay contact rating with current 1A @ 30VDC, 0.5A @ 120VAC

yOperating voltage and Max. current consumption: 0.76A @ 12VDC,

0.38A @ 24VDC, 0.19A @ 48VDC. Power consumption: 9.12W Max

yPower Supply: Redundant DC Terminal Block power inputs or 12VDC

DC JACK with 100-240VAC external power supply

y-40℃to 75℃(-40℉to 167℉) operating temperature range

Tested for functional operation @ -40℃to 85℃(-40℉to 185℉)

ySupports Din-rail, Panel, or Rack Mounting installation

yFront panel status LEDs

Packing List

When you unpack this product package, you will find the items listed below.

Please inspect the contents, and report any apparent damage or missing

items immediately to our authorized reseller.

yThe Media Converter

yUser’s Manual

yAC to DC Power Adaptor and Power Cable (optional)

Hardened Media Converter

One-Channel Media Converter

Ports

The Converter provides one TX port and one FX port. For the FX port, it

provides options of

Multi-mode fiber using SC or ST connector or

Single-mode fiber using SC or ST connector or

WDM fiber using single SC connector

For the TX port, it uses RJ-45 connector, auto-MDIX, and auto negotiates

10/100Mbps and full/half-duplex.

Port Settings

Port settings are made very simple by means of a DIP (Dual Inline Package)

switch at the front panel of the harden media converter.

Default DIP switch settings:

1 2 3 4 5 6

DIP switch

There are six pins on the DIP switch for port settings. Refer to the table below

for more details.

DIP

switch

No.

0 1

1 Disable LFPT Enable LFPT LFPT:

link fault pass

through

2 Enable auto negotiation for TX port Enable forced mode for TX port

3 TX port forced to 100Mbps TX port forced to 10Mbps

4 TX port forced to full duplex mode TX port forced to half duplex mode

5 FX port forced to full duplex mode FX port forced to half duplex mode

6 Disable link down alarm Enable link down alarm

yFirst, disconnect the converter from the power. Then toggle Pin 2 of the

DIP switch to position 1 to enable the forced mode for TX port.

<NOTE>Pin 2 must be toggled to position 1 prior to speed and duplex mode

settings manually.

yToggle Pin 3 to position 0 to force the TX port at the speed of 100Mbps.

Or toggle Pin 3 to position 1 for 10Mbps speed.

Andere Handbücher für EL900 Series

Inhaltsverzeichnis

Andere EtherWAN Medienkonverter Handbücher

EtherWAN

EtherWAN EL100T Bedienungsanleitung

EtherWAN

EtherWAN EL2242 Series Bedienungsanleitung

EtherWAN

EtherWAN EL900 Series Bedienungsanleitung

EtherWAN

EtherWAN EL2242 Series Bedienungsanleitung

EtherWAN

EtherWAN EL900 Series Bedienungsanleitung

EtherWAN

EtherWAN EL110 Series Bedienungsanleitung

EtherWAN

EtherWAN EL1032T Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EM1100 Bedienungsanleitung

EtherWAN

EtherWAN EM120 Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL1032T Series Bedienungsanleitung

EtherWAN

EtherWAN EL2326L Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL1142 Series Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EL42011 Series Bedienungsanleitung

EtherWAN

EtherWAN EMC1200R Bedienungsanleitung

EtherWAN

EtherWAN EMC400 Bedienungsanleitung

EtherWAN

EtherWAN EMC1200R Bedienungsanleitung

EtherWAN

EtherWAN EL2321 Bedienungsanleitung

EtherWAN

EtherWAN EL100 Bedienungsanleitung

EtherWAN

EtherWAN EMC1600 Series Bedienungsanleitung

EtherWAN

EtherWAN EL50 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung