EtherWAN ER58000 Series Bedienungsanleitung
Copyright 2014 EtherWAN Systems, Inc. Page 1
All Rights Reserved
ER58000 rev. 1.0
12/2/2014
1 Unpacking
Unpack the items. Your package should include:
One ER58000 Series hardened managed
switch
Rack-mounting hardware brackets
One CD containing this user’s guide
If items are missing or damaged, notify your
EtherWAN representative. Keep the carton and
packing material.
2 What Else You Need
Appropriate cables for data ports
Personal computer or laptop
3 Select a Location
Desktop installations: Mount on a flat table
or shelf surface.
Rack installations: Use a 19-inch (48.3-
centimeter) EIA standard equipment rack
that is grounded and physically secure.
Identify a power source within 6 feet (1.8
meters).
Choose a dry area with ambient temperature
between -40 and 75ºC (-40 and 167ºF).
Be sure there is adequate airflow.
4 Connect to the Data Ports
Your switch has the following ports:
8 10/100Base-M12 D-Code 4-pin female ports
2 Gigabit-M12 A-Code 8-pin female/LC ports
10/100Base-M12 Ports
These ports support Power over Ethernet (PoE).
They conform to IEEE802.3at and provide up to
30W per port, with a total power budget of
120W. Use these ports to connect to devices such
as an IP surveillance camera or a Voice Over
Internet Protocol (VoIP) phone.
Gigabit-M12 Ports
These ports come as 10/100/1000Base-TX,
1000Base-SX, or 1000Base-LX interfaces.
These ports can connect to network devices such
as a computer, printer, network video recorder
(NVR), network storage, or they can connect to
the network itself. Wear an ESD-preventive wrist
strap before connecting to these ports.
5 Apply DC Power
The switch supports two sets of power supplies —
power input 1 and power input 2.The M23 6-pin
male connector on the front panel is used for the
dual power inputs. Use a power cord with an M23
6-pin female connector to connect the power
inputs to the switch.
Pin
Description
Power 2
24-48VDC
Power Ground
Power 1
24-48VDC
Power Ground
Earth Ground
Relay Output Rating
1A @ 250VAC
Pin
Description
1
PWR1 Live / DC + (24-48VDC)
2
PWR1 Neutral / DC -
3
Chassis Ground
4
PWR2 Neutral / DC -
5
PWR2 Live / DC + (24-48VDC)
ER58000 Series Hardened Managed Ethernet Switch
Installation Guide
Continued on next page
ER58000 Managed Switch Installation Guide
Copyright 2014 EtherWAN Systems, Inc. Page 2
All Rights Reserved
ER58000 rev. 1.0
12/2/2014
Power-Up Sequence
When you apply DC power:
All Link/ACT LEDs blink momentarily.
The Power LED goes ON.
LEDs for ports connected to a device flash.
6 Front Panel LEDs
LED
Color
Status
Power 1
Power 2
Green
ON = power on.
OFF = power off.
10/100Base-TX LEDs
Link/Act
Green
ON = valid network connection established.
Flashing = port sending or receiving data.
10/100/1000Base-TX LEDs
Link/Act
Green
ON = valid network connection established.
Flashing = port sending or receiving data.
1000Base-SX/LX LEDs
Link/Act
Orange
ON = valid network connection established.
Flashing = port sending or receiving data.
7 Managing the Switch
The following procedures are optional, but
recommended for a basic configuration.
A. Connect a PC to an available switch port
using an appropriate cable.
B. Confirm that the Link/ACT LED for the switch
port to which the PC is connected is ON. If
not, choose a different port.
C. Configure the PC’s TCP/IP settings to use the
subnet 192.168.1.Xand subnet mask
255.255.255.0, where Xis a number from 2
to 254 other than 10.
D. In a Web browser address bar, type
http://192.168.1.10 and press Enter.
E. Log in to the management interface:
F. Change the system name:
- In the left pane, click +next to System,
then click System Name/Password.
- On the right side, click in the System
Name text box.
- Replace the name shown with a name you
want to assign to the switch.
- Click the Update Setting button.
G. By default there is no password assigned to
the switch. To add a password:
- In the page above, click in the Password
text box, enter a password, and retype it
in the Retype Password text box.
- Click Update Setting below the
Retype Password text box.
H. Change the switch’s IP address and subnet
mask to match the scheme on your network:
Andere EtherWAN Schalten Handbücher
EtherWAN
EtherWAN L-EX17008A Bedienungsanleitung
EtherWAN
EtherWAN EX41941 Bedienungsanleitung
EtherWAN
EtherWAN EX19164 Bedienungsanleitung
EtherWAN
EtherWAN EX42008 Series Bedienungsanleitung
EtherWAN
EtherWAN OttoE TG103 Series Bedienungsanleitung
EtherWAN
EtherWAN EX17082 Bedienungsanleitung
EtherWAN
EtherWAN EX17082 Bedienungsanleitung
EtherWAN
EtherWAN EX42000 Series Bedienungsanleitung
EtherWAN
EtherWAN EX78900X Series Bedienungsanleitung
EtherWAN
EtherWAN EX19164A Bedienungsanleitung
EtherWAN
EtherWAN EX42914 Series Bedienungsanleitung
EtherWAN
EtherWAN EX62000 Bedienungsanleitung
EtherWAN
EtherWAN EX17242 Bedienungsanleitung
EtherWAN
EtherWAN EX73900X Series Bedienungsanleitung
EtherWAN
EtherWAN EX17082A Bedienungsanleitung
EtherWAN
EtherWAN EX78000 Series Bedienungsanleitung
EtherWAN
EtherWAN EX43000 series Bedienungsanleitung
EtherWAN
EtherWAN EX63000 Series | Bedienungsanleitung
EtherWAN
EtherWAN EX61000A Bedienungsanleitung
EtherWAN
EtherWAN EX17908 Series Bedienungsanleitung
