EuroLite SCAN 75 LED SCANNER Bedienungsanleitung

SCAN 75 LED SCANNER

User Manual

Ver1.0

Table of contents

INTRODUCTION ……………………………………………….…………………………..2

SAFETY INSTRUCTIONS…………………………………………………………………2

OPERATING DETERMINATIONS…………………………………………….…………..3

DESCRIPTION OF THE DEVICE…………………………………………………………4

INSTALLATION………………………………………………………………….…………..5

OPERATION……………………………………………………………………….………...6

Stand alone operation…………………………………………………………….…………6

Master slave operation…………………………………………………………….……..…6

DMX controlled operation………………………………………………………….…….…6

Addressing…………………………………………………………………………….…..…6

Control board………………………………………………………………………….…..…6

DMX protocol………………………………………………………………………….…..…7

TECHNICAL SPECIFICATIONS…………………………………………………….……7

Every person involved with installation. operation and maintenance of this fixture has to

- be qualified

- follow the instruction of this manual

- consider this manual to be part of the total product

- Keep this manual for the entire service life of the product

- pass this manual to every future owner or use of the product

INTRODUCTION

Thank you for choosing our fixture, if you follow up the instruction given in this manual we be sure that

you will enjoy this product for a long period of time

SAFETY INSTRUCTION

This device has left our premises in absolutely perfect condition .In order to maintain this condition and

to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruction and

warning notes written in this user manual.

Important: Damages caused by the disregard of this user manual are not subject o warranty, the dealer

will not accept liability for any resulting defects of problem. If the device had been exposed to drastic

temperature fluctuation (e.g. after transportation),do not switch it on immediately. The arising

condensation water might damage your device. Leave the device switched off until it had reached room

temperature. Please make sure that there are no obvious transport damages, should you notice any

damages on the AC connection cable or on the casing, do not take the device into operation and

immediately consult your local dealer.

OPERATING DETERMINATIONS

This device is designed for permanent operation. Consistent operation breaks will ensure that the

device will serve you for a long time without defects. Do not shake the device. Avoid brute force when

installing or operation the device. Never lift the fixture by holding it at the projector-head. As the

CAUTION!

Be careful with your operations, With a dangerous voltage you can suffer a dangerous electric

shock when touching the wires.

CAUTION !

Keep this device away from rain and moisture

Unplug mains lead before opening the housing

For your own safety, please read this user manual carefully before you initially start-up

mechanics may be damaged. When choosing the installation-spot, please make sure that the device is

not exposed to extreme heat, moisture or dust. There should not be any cable lying around. Please

make sure that the fixture can not be touched or bumped. Your endanger your own and the safety of

others.

DESCRIPTION OF THE DEVICE

Features

> High power 75w white led

>50000 hours lifetime and lower power consumption

> 15 or 19 DMX channel in optional

> Beam angle 12 degree 34000Lux at 1m,14.5 degree 28000Lux at 1m

> Manual zoom 12 or 14.5 degree

>1 Color wheel with 8 diachronic colors plus open

> 1 Rotated gobo wheel with 7 rotated interchangeable gobos plus open.

> Rotated 3 facet prism with speed adjustable and variable direction

> 0~100% linear dimmer and 1-18 times/sec high speed electronic strobe

> DMX512, master-slave and sound activated controllable and auto with 8 built-in programs

INSTALLATION

Rigging

The installation of the projector has to be built and constructed in a way that it can hold 10 times the

weight for 1 hour without any harming deformation.

IMPORTANT!OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating

working load limits, installation material being used, and periodic safety inspection of all installation

material and the projector. If you lack these qualifications, do not attempt the installation yourself, but

instead use a professional structural rigger. Improper installation can result in bodily injury and or

damage to property. The projector had to be installed out of the reach of people

DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable

material(decoration articles, etc.)within a distance of min.0.5m.

DMX 512 connection/ connection between fixture

The wires must not come into contact with each other, otherwise the fixture will not work at all or

properly. Please note the starting address depends upon which controller is being used. Only use a

DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one

fixture to another

Connection with the mains.

The earth has to be connected. The device must only be connected with an electric installation carried

out in compliance with IEC standards.

OPERATION

After you connected the effect to the mains, The fixture starts running

Stand Alone operation

In the stand alone mode, the fixture can be use without controller

Master/slave-operation

The master/slave-operation enables that several devices can be synchronized and controlled by one

master-device

DMX controlled operation

You can control the projectors individually via your DMX-controller

Addressing

The control board allows you to assign the DMX starting address,

Note;it’s necessary to insert the XLR termination plug (with 120ohm) in the last device in the link in order

to ensure proper transmission on the DMX data link.

CONTRO L BOARD

The control board offer several features :you can simple set the starting address, run the

pre-programmed program or make a reset

the main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by

pressing Up or Down .Press the Enter-button in order to select the desired menu. You can change the

selection by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave

every mode by pressing the Mode/Esc-button .The functions provided are described in the following

setting.

MENU MAP

The device has two operation modes, It can be operated in Stand Alone or in DMX controlled

Mode

DMX

Auto 1 /Auto 2 Auto 3 /Auto 4

XY effect 1/ XY effect 2 / XY effect 3 /XY effect 4

Random effect /Sound

DMX address

Setting DMX address from 001-512

Channel mode

Select 15 or 19 DMX channel

X reverse

ON/OFF

Y reverse

ON/OFF

XY exchange

ON/OFF

XY encoder

ON/OFF

Screen mode

ON display no light after 30 seconds

OFF display light always on

Version

Software version/DMX channel/run time/Total use time

Reset

ON/OFF

DMX-protocol

15/19 DMX channel mode

channel

value

function

0-255

Pan movement

0-255

Pan Fine

Pan fine movement

0-255

Tilt movement

0-255

Tilt Fine

Tilt fine movement

0-255

Pan Tilt speed

Pan/Tilt movement with increasing speed

0-3

4-251

252-255

Shutter/Strobe

Shutter close

Strobe with increasing speed

Shutter open

0-255

Dimmer

0~100% linear dimmer

0-4

5-9

10-14

15-19

20-24

25-29

30-34

35-39

40-44

45-49

50-54

55-59

60-64

65-69

70-74

75-79

80-84

85-89

90-255

Color wheel

White

White+Red

Red

Red+Orange

Orange

Orange+Green

Green

Green+Light blue

Light Blue

Light Blue+Purple

Purple

Purple+Yellow

Yellow

Yellow+Blue

Blue

Blue+Pink

Pink

Pink+White

Rainbow effect with increasing speed

Ps: In 5 have two half color, 4 means 60% red + 40%

white

Gobo Wheel

0-4

5-9

10-14

15-19

20-24

25-29

30-34

35-39

40-129

130-134

135-220

221-225

226-230

231-235

236-240

241-245

246-250

251-255

Open/White

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Anti-clockwise gobo change with decreasing speed

White

Clockwise gobo change with decreasing speed

Gobo 1 shaking

Gobo 2 shaking

Gobo 3 shaking

Gobo 4 shaking

Gobo 5 shaking

Gobo 6 shaking

Gobo 7 shaking

0-63

64-127

128-191

192-255

Gobo Rotation

Gobo angle adjustment with slowdown speed

Anti-clockwise gobo rotation with increasing speed

Clockwise gobo rotation with increasing speed

Rotated gobo shake with double direction in

increasing speed

0-255

Focus

0~100% from far to near adjustment

0-127

128-255

Prism

No function

Prism effect

0-63

64-127

128-191

192-255

Rotated prism

Prism angle adjustment slowdown speed

Rotated prism with increasing speed in anti-clockwise

Rotated prism with increasing speed in clockwise

Rotated prism shake with double direction in

increasing speed

0-5

6-9

10-255

Macro function

Fade delay in dimmer on

Fade delay in dimmer off

Buitl-in Program

0-25

26-45

46-103

104-119

120-190

191-205

Rest

No function

Reset for Color/gobo/prism/rotated gobo prism/focus

No function

Reset for XY

No function

All rest

206-255

No function

0-4

5-9

10-14

15-19

20-24

25-29

30-34

35-39

40-44

45-49

50-54

55-59

60-64

65-69

70-74

75-79

80-89

85-89

90-94

95-114

115-134

135-154

155-174

175-194

195-214

215-234

235-254

255

Color wheel effect

White

White+Red

Red

Red+Orange

Orange

Orange+Green

Green

Green+light Blue

Light Blue

Light Blue+Purple

Purple

Purple+Yellow

Yellow

Yellow+Blue

Blue

Blue+Pink

Pink

Pink+White

White

Red

Orange

Green

Light Blue

Purple

Yellow

Blue

Pink

White

0-255

Color wheel Speed

Color wheel in decreasing speed

0-255

Prism Speed

Prism in decreasing speed

0-255

Gobo wheel Speed

Gobo wheel in decreasing speed

TECHNICIAL SPECIFICATIONS

Model

SCAN 75 LED SCANNER

Voltage

110V- 250V / 50-60Hz

Power consumption:

120W

LED

75w high power white led

Net Weight / Gross Weight

5.2 / 6.5Kgs

Fixture dimensions

40x36x12cm

Inhaltsverzeichnis

Andere EuroLite DJ-Equipment Handbücher

EuroLite

EuroLite 42103411 Bedienungsanleitung

EuroLite

EuroLite LED TMH-4 Bedienungsanleitung

EuroLite

EuroLite LED PST-9W Bedienungsanleitung

EuroLite

EuroLite LED Panel Ball 9 Bedienungsanleitung

EuroLite

EuroLite LED WF-30 Bedienungsanleitung

EuroLite

EuroLite AKKU UP-4 Entry QCL Spot Bedienungsanleitung

EuroLite

EuroLite LED FX-250 Bedienungsanleitung

EuroLite

EuroLite CHASER 405 Bedienungsanleitung

EuroLite

EuroLite ML-600 ABL Bedienungsanleitung

EuroLite

EuroLite UV-PSYCHO-WHEEL Bedienungsanleitung

EuroLite

EuroLite LED SCY-5 Bedienungsanleitung

EuroLite

EuroLite Mirror Tunnel 4713 Bedienungsanleitung

EuroLite

EuroLite LED Triple FX Laser Box Bedienungsanleitung

EuroLite

EuroLite LED SPACE BALL 35 Bedienungsanleitung

EuroLite

EuroLite LED SCY-500 Bedienungsanleitung

EuroLite

EuroLite LED PAR-56 TCL Short Spots Bedienungsanleitung

EuroLite

EuroLite Board 6S Bedienungsanleitung

EuroLite

EuroLite Techno Strobe 250 Bedienungsanleitung

EuroLite

EuroLite Foam 1500 MK2 Bedienungsanleitung

EuroLite

EuroLite LED FE-6 Bedienungsanleitung

EuroLite

EuroLite LED IP STRIP SET 45 RGB Bedienungsanleitung

EuroLite

EuroLite BIG SNOW Bedienungsanleitung

EuroLite

EuroLite LED FE-2000 Bedienungsanleitung

EuroLite

EuroLite Techno Strobe 350 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung

Chauvet

Chauvet ovation B-2805FC Bedienungsanleitung

Eurotherm

Eurotherm LED TMH-X18 Bedienungsanleitung

American DJ

American DJ HMI 575TM Bedienungsanleitung