Everbilt LTS250A Bedienungsanleitung

THANK YOU

We appreciate the trust and confidence you have placed in Everbilt Utility Pump. We strive to continually create quality

products designed to enhance your home. Visit us online to see our full line of products available for your home

improvement needs

Thank you for choosing Everbilt!

TROUBLESHOOTING GUIDE

UTILITY PUMP

Model#

LTS250A

SBA025HPACK

UTA02510

PSUT03308AP

SSB300

SKU#(US)

1002303674

1002921354

1000026647

SKU#(CA)

1000427445

1000143218

1001102847

1001600783

Questions, problems, missing parts? Before returning to the store call

Everbilt Customer Service

8 a.m. - 6 p.m., EST, Monday-Friday

1-844-241-5521

WWW.HOMEDEPOT.COM

WWW.HOMEDEPOT.CA

Rev. 07/21/21

Utility Sink Pump - LTS250A, SBA025HPACK .......................................... Page 2

2-in-1 Utility pump - UTA02501 ................................................................. Page 3

Pool Cover Pump - PSUT03308AP............................................................ Page 4

Waterfall Utility Pump - SSB300................................................................. Page 5

2Everbilt Utility Pump Troubleshooting Guide

Safety Warnings

All electrical work should be performed by a licensed electrician.

WARNING: Risk of electrical shock. Disconnect power to the pump before servicing. Do not handle the

pump with wet hands or when standing on a wet or damp surface.

WARNING: Risk of fire or explosion.Pump water only with this pump. Do not use this pump in the presence

of flammable or explosive vapors.

CAUTION: Motors run hot. Do not touch the motor housing during operation.

Utility Sink Pump - LTS250A, SBA025HPACK

Problem 1: Pump does not run when water flows in from the sink.

Possible Causes

Corrective Action

1. The pump is not plugged in. 1. Make sure the plug is connected.

2. The circuit breaker has tripped. 2. Reset the circuit breaker by switching the breaker to the "ON" position.

3. The pump impeller is stuck. 3. Unplug the pump. To clear the impeller, Refer to "Maintenance" in the

owner's manual.

4. The sink stopper is in the drain. 4. Remove the stopper.

5. Not enough water to activate the pump. 5. Keep water running until the pump turns on.

6. Diaphragm switch has failed. 6. Refer to the owner's manual and verify the installation is correct on the

discharge side. Contact customer support for next steps.

Problem 2: Pump runs but does not empty sink.

Possible Causes

Corrective Action

1. The drain is clogged. 1. Clear the drain screen.

2. The discharge line is clogged. 2. Unplug the pump, open and clear the discharge line.

3. The check valve is installed incorrectly.

3. Make sure the flow arrow on the check valve points away from the

pump.

Problem 3: Pump cycles ON and OFF when there is no water in the sink.

Possible Causes

Corrective Action

1. The check valve is not installed.

1. Unplug the pump. Refer to the "Installation" section of the owner's

manual to install the check valve properly.

2. The check valve is jammed. 2. Unplug the pump. Open the discharge line and clean the check valve.

Problem 4: Pump cycles ON and OFF when the sink is full.

Possible Causes Corrective Action

1. The shut-off valve is not installed.

1. Unplug the pump. Refer to the "Installation" section of the owner's

manual to install the shut-off valve.

2. The shut-off valve is out of adjustment.

2. Refer to "Adjusting the Flow" section of the owner's manual to correctly

adjust the shut-off valve.

3Everbilt Utility Pump Troubleshooting Guide

2-in-1 Utility pump - UTA02510

Submersible Utility & Non-submersible Transfer.

Pump does not start or run.

Possible Causes Corrective Action

1. The circuit breaker has tripped.

1. Reset the circuit breaker by switching the breaker to the "ON" position.

2. The plug is disconnected.

2. Make sure the plug is securely connected.

3. The plug is corroded. 3. Clean the prongs of the plug.

4. The motor has failed. 4. Replace the pump.

Submersible Utility

Problem 1: Pump does not pump water.

Possible Causes Corrective Action

1. The screen is blocked.

1. Clean the screen.

2. The hose is bent, kinked or coiled too

tightly.

2. Straighten the hose.

3. There is trapped air inside the pump, a

condition called "airlock".

3. Clean the anti-air lock hole and make sure it is not blocked.

4. Pump inlet is blocked by debris. 4. Open the bottom cover to clean out the debris.

Non-Submersible Transfer

Problem 1: Pump does not prime.

Possible Causes Corrective Action

1. The suction line has air leaks.

1. Tighten the hose connection. Replace the hose washer if needed.

2. Debris has collected on the strainer.

2. Clean debris from the strainer.

3. Pump needs to be primed or re-primed. 3. Refer to the owner's manual for priming instructions.

4. The suction strainer is not attached to the

inlet hose when removing surface water.

4. Attach the suction strainer to the inlet hose.

5. Suction strainer is floating in the water.

5. Suction strainer needs to be flat on the bottom surface of whatever you

are draining.

Problem 2: Flow rate is too low.

Possible Causes Corrective Action

1. The hose is kinked or coiled tightly.

1. Straighten the hose.

2. The strainer or hose is blocked.

2. Clean the strainer or hose.

3. The discharge hose is too long. 3. The hose length should be no longer than 25'

4. Incorrect Garden hose on

outlet/discharge.

4. Use standard garden hose, not "expandable" hose.

4Everbilt Utility Pump Troubleshooting Guide

Pool Cover Pump - PSUT03308AP

Problem 1: Pump will not start or run.

Possible Causes Corrective Action

1. The circuit breaker has tripped.

1. Reset the circuit breaker by switching the breaker to the "ON" position.

2. The plug is disconnected.

2. Make sure the plug is securely connected.

3. The plug is corroded.

3. Clean the prongs of the plug.

4. The motor has failed.

4. Replace the pump.

5. Water Sensor is clogged with debris.

5. Unplug the pump and remove Strainer Base. Lay the pump on its side.

Open the bottom cover of the sensor. Flush the water sensor housing

with fresh water until the probes are clean.

6. Water depth is under 2 inches.

6. Make sure the pump is level and flat on the pool cover. Pump will not

start until the water reaches 2 inches depth.

Problem 2: Pump starts and stops too often.

Possible Causes Corrective Action

1. Water is flowing back from the hose.

1. Make sure the Check Valve/Adapter is installed correctly. Replace

check valve if needed.

2. Water Sensor is clogged with debris.

2. Unplug the pump and remove Strainer Base. Lay the pump on its side.

Open the bottom cover of the sensor. Flush the water sensor housing

with fresh water until the probes are clean.

3. Pump is not sitting flat on the pool cover.

3. Position the pump level and flat on the pool cover.

Problem 3: Pump runs continuously or will not shut off.

Possible Causes Corrective Action

1. Water Sensor is clogged with debris.

1. Unplug the pump and remove Strainer Base. Lay the pump on its side.

Open the bottom cover of the sensor. Flush the water sensor housing

with fresh water until the probes are clean.

2. Pump housing is cracked.

2. Inspect housing for cracks. If there are cracks, replace the pump.

Problem 4: Pump operates but delivers little or no water.

Possible Causes Corrective Action

1. Impeller is stuck or clogged with debris.

1. Unplug the pump and remove Strainer Base. Remove the bottom plate.

Clean out debris on and around the impeller. Make sure the impeller

rotates freely.

2. Maximum lift exceeds 28' feet.

2. Reduce the lift to under 28'.

3. The hose is kinked or coiled tightly.

3. Straighten the hose. Be sure to use standard garden hose, not

"expandable" hose.

4. The Strainer Base is clogged with debris.

4. Unplug the pump. Remove the Strainer base and flush with clean

water until it is clean.

5Everbilt Utility Pump Troubleshooting Guide

Waterfall Utility Pump - SSB300

Problem 1: Pump will not start or run.

Possible Causes Corrective Action

1. The circuit breaker has tripped.

1. Reset the circuit breaker by switching the breaker to the "ON"

position.

2. The plug is disconnected. 2. Make sure the plug is securely connected.

3. The plug is corroded. 3. Clean the prongs of the plug.

4. Thermal overload protector tripped.

4.Unplug the pump for 30 minutes. Make sure the impeller is not

stuck or clogged. Only pump cold water with this pump.

5. The motor has failed. 5. Replace the pump.

Problem 2: Pump operates but delivers little or no water.

Possible Causes Corrective Action

1. Impeller is stuck or clogged with debris.

1. Unplug the pump. Refer to the owner's manual for cleaning

instructions.

2. The impeller is worn out or broken. 2. Replace the impeller.

3. The inlet screen is blocked.

3. Clean the screen. Refer to the owner's manual for cleaning

instructions.

4. There is trapped air inside the pump, a

condition called "airlock".

4. If a check valve is installed, drill a 1/8" hole between the pump

discharge and check valve.

5. The hose is loose. 5. Secure the hose.

Andere Handbücher für LTS250A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Everbilt Wasserpumpe Handbücher

Everbilt

Everbilt UTA02510 Bedienungsanleitung

Everbilt

Everbilt SW07501T Bedienungsanleitung

Everbilt

Everbilt EBAU33 Bedienungsanleitung

Everbilt

Everbilt DP370C Bedienungsanleitung

Everbilt

Everbilt 9236060 Bedienungsanleitung

Everbilt

Everbilt EBAU25-PCP Bedienungsanleitung

Everbilt

Everbilt SBA025RP Bedienungsanleitung

Everbilt

Everbilt EBTP1 Bedienungsanleitung

Everbilt

Everbilt HDPCP25 Bedienungsanleitung

Everbilt

Everbilt UT03301 Bedienungsanleitung

Everbilt

Everbilt SP03302VD Bedienungsanleitung

Everbilt

Everbilt EFLS15CI-HD Bedienungsanleitung

Everbilt

Everbilt LTS250A Bedienungsanleitung

Everbilt

Everbilt HDS30 Bedienungsanleitung

Everbilt

Everbilt SBA025BC Bedienungsanleitung

Everbilt

Everbilt DPJC125 Bedienungsanleitung

Everbilt

Everbilt SBF300 Bedienungsanleitung

Everbilt

Everbilt UTA02510 Bedienungsanleitung

Everbilt

Everbilt EB-PUMP-T Bedienungsanleitung

Everbilt

Everbilt SCN250-LQ Bedienungsanleitung

Everbilt

Everbilt THD1100 Bedienungsanleitung

Everbilt

Everbilt PUP63-HD Bedienungsanleitung

Everbilt

Everbilt ZE00802A Bedienungsanleitung

Everbilt

Everbilt PCP10001-VSP Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung