Evertz EQX Bedienungsanleitung

EQX Unpacking Instructions

Revision 1.0 EQX - 1

1. EQX PACKAGING MATERIALS

The instructions provided in this document outline the EQX unpacking procedure. Please review the

following instructions before opening and moving the shipping container. Once the EQX is unpacked,

please refer to the EQX user manual for instructions on installing the router.

The Evertz EQX packaging consists of the following components:

 Wooden shipping container (consists of two wooden side panels, one front panel, one back panel

and a wooden top cap)

 Pallet

 Foam packaging materials

 Protective Bags

 Unpacking Instructions and EQX User manual

Side View of Clip

Front View of Clip

Tab

Figure 1-1: EQX Shipping Container

Foam End

Figure 1-2: EQX with Shipping Panels

Removed

EQX Unpacking Instructions

EQX - 2 Revision 1.0

2. DISMANTLING THE WOODEN SHIPPING CONTAINER

Please read and follow the instructions outlined below in order to safely dismantle the wooden shipping

container:

Use caution when handling the packaging components. The wooden side

panels, wooden cap and pallet may have sharp metal edges.



There is a cone attached to the top of the EQX shipping container to prevent

people from stacking objects on the container. If the cone has been removed or

crushed, this may indicate that objects were stacked on the unit.

To dismantle the wooden shipping container, please follow the steps outlined below:

1. Three people are required in order to safely dismantle the shipping container. When moving the

system to a different location, it is essential that a handcart, pallet jack, or forklift be used. Care

should be taken to avoid jarring the EQX frame.

CAUTION – Do not attempt to lift or move the fully assembled EQX from the

pallet. Please note that the weight of the EQX can range from 400 lbs (181.44

kg) to 500 lbs (226.8 kg) depending on the type of unit shipped (16RU or 26RU).

2. The dimensions of the EQX shipping container are: 40-inches (101.6 cm) wide, 40-inches (101.6

cm) long, and 56 inches (142.2 cm) high (66 inches including the cardboard shipping cone).

Before moving the shipping container, take note of the dimensions to ensure that there is sufficient

clearance space when transporting it through doors and passageways. Move the EQX shipping

container as close to the installation location by transporting it via a handcart, pallet jacket or

forklift. Ensure that there is an adequate amount of space to comfortably unpack and assemble

the system.

3. It is imperative that at least two people are securing the box while another person removes the

clips and panels to ensure that the panels do not fall and cause personal injury or damage to the

EQX unit.

4. There are 8 clips securing each wooden side panel to the front and back panels. Remove each

clip by pressing the tab on the clip and pushing the clip out from under the metal clasp. Repeat

this step for all 8 clips. At this time, DO NOT remove the clips securing the panels to the top cap or

bottom pallet.

5. Repeat step 4 to unhinge the other side panel.

6. All 16 side clips should now be removed from the side, front and back panels. Depending on the

shipping container size there may be 8, 10 or 14 clips securing the cap to the top of the wooden

packaging unit. Remove each clip by pressing the tab on the clip and pushing the clip out from

under the metal clasp.

EQX Unpacking Instructions

Revision 1.0 EQX - 3

7. Once all the clips are removed from the top cap, ensure at least two people are securing the side

panels while another person carefully lifts and removes the top cap.

8. Ensure at least two people are safely securing the side, front and back panels before removing the

bottom clips. Remove the 2, 3 or 4 clips that are securing the front panel to the pallet. Carefully lift

and remove the panel. Set the panel aside. Repeat this procedure for the remaining panels.

It is important to retain the shipping container, shipping container materials and

accessories for future shipping use.

9. Once all the panels are removed, set them aside. Remove the foam cap ends from the top and

bottom of the EQX.

10. Remove the protective packaging bag that is covering the EQX.

11. Open the EQX door and remove the protective packaging bag(s) from inside the unit.

12. Remove the bolts from the side and bottom ears of the triangle rack mount. The accessory box

that was shipped with your EQX contains the two wrenches needed to loosen the bolts. Use the

7/16” size wrench to remove the side bolts, and the 9/16” size wrench to remove the bottom bolts.

13. Once the bolts are removed, the EQX can be moved from the pallet and installed in the desired

location. Please refer to the EQX user manual for installation and operation instructions.

Andere Handbücher für EQX

Inhaltsverzeichnis

Andere evertz Netzwerk-Hardware Handbücher

evertz

evertz 8010TM Bedienungsanleitung

evertz

evertz 7700 7780ASI-IP2 Bedienungsanleitung

evertz

evertz EQT Series Benutzerhandbuch

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 5700ACO Bedienungsanleitung

evertz

evertz 7720AD Series Bedienungsanleitung

evertz

evertz 5010-GPSII Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz HD9525LG Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 8950 Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz Quartz D9 Montage- und Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 9531 Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7780DM-LB Series Bedienungsanleitung

evertz

evertz X-9512 Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

evertz

evertz 9625DSK-LGA Bedienungsanleitung

evertz

evertz 5600ACO Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

evertz EQX Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken