Evikon PluraSens E2658 Series Bedienungsanleitung

PluraSens®

Hydrogen Sulﬁde Detector-Transmitter

E2658-H2S

User Manual

E2658-H2S Rev 12.03.2021
Table of contents
Hydrogen Sulﬁde 3
Speciﬁcations 4
Product description 6
Safety requirements 6
Operating conditions 7
Installation guidelines 7
Mounting dimensions 9
Sensor probe handling 10
Gas sensor replacement procedures 10
Electrical connections 11
Operation 13
Maintenance 13
Calibration 13
Delivery set 14
Order code for E2658-H2S options 14
Conﬁguring 15
Return to default settings 15
Modbus RTU Communication 16
RS485 communication interface 16
Communication parameters 16
Modbus holding registers 16
Warranty 21
Manufacturer contacts 21
2

E2658-H2S Rev 12.03.2021

Hydrogen Sulﬁde

Colorless toxic, corrosive and ﬂammable gas with a smell of rotten eggs. Occurs in natural

gas, volcanic gases, petroleum, and some sources of well water. It results from the

anaerobic decay of sulfur-containing proteins, e.g. in sewers.

Synonyms: Hydrosulfuric acid, Sewer gas, Sulfuretted hydrogen.

Chemical formula

H2S

Molar weight

Conversion

1 ppm = 1.40 mg/m3

Relative gas density (to air)

1.17

Boiling point

−60 °C

Low explosive limit (LEL), % vol.

in air

4.0

Upper explosive limit (UEL), %

vol. in air

44.0

Odor

The characteristic smell of rotten eggs. Above 30 ppm, the odor is

described as sweet or sickeningly sweet.

Odor threshold

0.01-1.5 ppm

Note: Sense of smell becomes rapidly fatigued and can NOT be

relied upon to warn of the continuous presence of H2S.

Hazards

Highly ﬂammable, explosive gas.

Broad-spectrum poison, mostly affecting the nervous system. At

low concentrations causes eye irritation, a sore throat and cough,

nausea, shortness of breath, and pulmonary edema. Long-term,

low-level exposure results in fatigue, loss of appetite, headache,

poor memory, irritability, and dizziness. Exposure to high levels

can induce immediate collapse, with loss of breathing and a high

probability of death.

Exposure limits

(Commission

Directive

2009/161/EU)

TWA

7 mg/mm3/ 5 ppm

STEL

14 mg/mm3/ 10 ppm

IDLH

(NIOSH)

140 mg/mm3/ 100 ppm

Conversion of ppm to mg/m3is calculated for 25°C and 1 atm.

E2658-H2S Rev 12.03.2021

Speciﬁcations

Sensor type

Electrochemical cell

Sampling method

Diffusion

Typical detection range

0...100 ppm

0...2000 ppm

Maximum overload

500 ppm

4000 ppm

Resolution / digital unit

0.1 ppm

2 ppm

Response time T90

< 30 s

< 25 s

Operating temperature

-30...+50 °C

-40...+50 °C

Sensor lifetime

> 2 years

Calibration interval

6 months

Signal update

Every 1 second

Power supply

11...30 VDC (default),

24 VAC or 90...265 VAC as options

Power consumption

< 2 VA

Analog outputs

2 × 4-20 mA / 0-10 V, user settable

Outputs assignment

OUT1 2 gas; OUT2 2 gas

Output scale width

> 10 × resolution

Recommended: 20-100% of the detection range

Load resistance

RL< (Us - 2 V) / 22 mA for 4-20 mA

RL> 250 kOhm for 0-10 V mode

Digital interface

RS485, Modbus RTU protocol

No galvanic isolation

Cable connections

Screwless spring-loaded terminals

Enclosure

Grey die-cast aluminum, wall mount, IP66

Cable glands

M25 for SWA cable or steel conduit Ø10...17 mm

Dimensions

H80 × W125 × D57 / H80 × W175 × D80 mm

Protection

Flameproof, ATEX: II 2 GD, Ex ed IIC T4 Gb

ATEX Approvals

Enclosure:

ATEX / IECEx DEMKO 13 ATEX 1327771U

II 2 G Ex c IIC Gb II 2 D Ex tb IIIC Db IP66

Glands:

ATEX / IECEx II2G Ex e II IP68

IBExU08ATEX 1063 X Ex II 1D Ex tD A20 IP 6x Ex

E2658-H2S Rev 12.03.2021

CE marking

According to 2014/30/EU and 2014/34/EU,

EN 61000-6-3:2020, EN 61326-1:2013 (EMC, Emissions)

EN 61000-6-1:2019, EN 61000-6-2:2019, EN 61326-2-1:2013 (EMC,

Immunity)

EN 60079-0:2018, EN 60079-1:2014, EN 60079-31:2014,

EN 60079-29-1:2016, EN 60079-29-2:2015, EN 60079-29-3:2014

Operating conditions

(operating temperature is speciﬁed above)

15...90 %RH non-condensing, 0,9...1,1 atm

Explosion-safe zones and ATEX Zones 2 and 22,

Non-aggressive atmosphere

Relay option

Output relays

2 × SPST relays (closing contact),

250 VAC / 30 VDC, 5 A max

Default alarm setpoints

(set/release)

LOW: 10 ppm/ 8 ppm

HIGH: 20ppm/16 ppm

Deﬁned by user

within 5-95% of the detection range

E2658-H2S Rev 12.03.2021

Product description

E2658 is a series of ﬂameproof gas detectors-transmitters intended for operation in safe

zones and ATEX Zones 2 and 22. E2658 series devices are based on PluraSens®

multifunctional platform and provide all its features. The instruments utilize gas sensors of

various types with excellent repeatability, stability, and long lifetime.

E2658 series provides two independent analog outputs OUT1 and OUT2, user-selectable to

4-20 mA or 0-10 V, proportional to gas concentrations. RS485 Modbus RTU digital

communication interface allows easy instrument conﬁguration and integration into various

automation systems.

The following features are available as an option:

●Two relays RE1 and RE2 with closing contacts. Relay outputs can be used to

switch alarm sirens, ventilation fans, shut-off valves, or other actuators,

●24 VAC or 230 VAC as options for power supply.

The version of your detector is marked on the package. If the symbol

⚠

is marked on the

equipment, consult the documentation for further information.

Safety requirements

Misuse will impair the protection of the product. Always adhere to the safety provisions

applicable in the country of use.

Do not perform any maintenance operation with the power on. Do not let water or foreign

objects inside the device.

Removal of the PCB from the enclosure voids the warranty. Do not touch the electronic

components directly, as they are sensitive to static electricity.

Connection diagrams can be found in the electrical connections section. The device might

not perform correctly or be damaged if the wrong power supply is connected.

It is crucial to tighten properly all the thread connections (screws, cable glands). Use ATEX

certiﬁed armored cables or cable conduits that are rated for use in the desired

environment.

A disconnecting device that is marked as such and easily accessible should be included in

the installation of this product.

The device should be properly earthed.

E2658-H2S Rev 12.03.2021

Operating conditions

The device should be used in a basic electromagnetic environment, where the latter is

deﬁned in EN 61326-1. Avoid strong mechanical shock and vibrations. Although E2658

series devices are suitable for use in the presence of ﬂammable dust, special precautions

should be taken when operating in a dusty environment. Dust may block the porous ﬁlter of

the sensor and compromise the results of the measurement. The detector should be

inspected regularly if used in a dusty atmosphere. Keep the instrument away from direct

sunlight. A sudden temperature or humidity change might affect the sensitivity of the

sensor. Make sure that installation and maintenance are performed in an explosion safe

atmosphere.

Installation guidelines

Before proceeding with the installation it is mandatory to read the Safety requirements

section and make sure to comply with all listed instructions. Installation standards EN

60079-29-2 and EN 45544-4 are also recommended for further instructions and related

information about the installation. During the installation of the detector-transmitter the

following points must be considered:

●Application (air quality control or leakage detection.)

●Properties of the space under investigation (room geometry, direction, and

velocity of airﬂows, etc.),

●Hydrogen sulﬁde is slightly heavier than air and spreads evenly in the room. The

recommended location is close to the potential leakage source.

●The device should be accessible for maintenance and repair.

The aforementioned conditions above will affect the coverage area of the device. however,

the coverage area for a detector-transmitter is usually between 2.5 to 5 meters radius.

For early leakage detection install the sensor as close as possible to the potential leakage

sources (ﬂanges, valves, pressure reducers, pumps, etc.), taking into consideration other

points listed above.

For general area monitoring without deﬁnite leakage sources, the detectors should be

distributed evenly in the room.

For personal safety control, the detectors are installed in the breathing zone (at the height

of the head of people or animals). The recommended sensor position is vertical, pointing

downwards.

E2658-H2S Rev 12.03.2021

The device is ﬁxed on the wall using two ﬁxing holes located outside the sealed area of the

device (see dimensional drawing). Unscrew four lid screws and detach the lid from the

detector. Fix the detector on the wall and earth the enclosure using an earthing terminal on

the side of the device.

NOTE! Never perform installation or maintenance in an explosive atmosphere!

E2658-H2S Rev 12.03.2021

Mounting dimensions

Front view

Bottom view

E2658-H2S Rev 12.03.2021

Sensor probe handling

The sensor probes of all types are equipped with a hydrophobic microporous PTFE ﬁlter to

protect the sensor from dust, dirt, and water drops. The ﬁlter should be replaced if it gets

strongly contaminated. To replace the PTFE ﬁlter, unscrew the sensor head cap and

remove the old ﬁlter. Place a new ﬁlter into the cap and tighten it again.

NOTE! Never stab or press the ﬁlter near its center where the sensor is located since this

may damage the sensor. Do not remove the ﬁlter as it may cause the device to show

incorrect values and/or break the sensor.

The recommended orientation of the sensor probe is vertical with the sensor tip pointing

downwards. This prevents the possible accumulation of condensed water on the sensor

protection ﬁlter.

Gas sensor replacement procedures

1. Remove the sensor head cap from the device,

2. Remove the PTFE ﬁlter (if it is not removed within the cap),

3. Remove the O-ring rubber,

4. Detach the electrochemical sensor from the device,

5. Insert the new electrochemical sensor inside,

6. Put back the O-ring rubber, PTFE ﬁlter, and the head cap, respectively.

Andere Handbücher für PluraSens E2658 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Evikon Sender Handbücher

Evikon

Evikon PluraSens E2648-N2O Bedienungsanleitung

Evikon

Evikon E2618-CO2 Bedienungsanleitung

Evikon

Evikon PluraSens E2670-Cl2 Bedienungsanleitung

Evikon

Evikon PluraSens E2658-O3 Bedienungsanleitung

Evikon

Evikon PluraSens E2670-NO Bedienungsanleitung

Evikon

Evikon PluraSens E2638-Cl2 Bedienungsanleitung

Evikon

Evikon PluraSens E2670-CO Bedienungsanleitung

Evikon

Evikon PluraSens E2218 Bedienungsanleitung

Evikon

Evikon PluraSens E2608-C2H4 Bedienungsanleitung

Evikon

Evikon PluraSens E2618 Series Bedienungsanleitung

Evikon

Evikon PluraSens E2618 Series Bedienungsanleitung

Evikon

Evikon PluraSens E2638 Series Bedienungsanleitung

Evikon

Evikon PluraSens E2638-N2O Bedienungsanleitung

Evikon

Evikon PluraSens E2670-PID Bedienungsanleitung

Evikon

Evikon PluraSens E2618-SO2 Bedienungsanleitung

Evikon

Evikon PluraSens E2608-PID Bedienungsanleitung

Evikon

Evikon PluraSens E2670-NO2 Bedienungsanleitung

Evikon

Evikon E2618-CO Bedienungsanleitung

Evikon

Evikon PluraSens E2218-DM Bedienungsanleitung

Evikon

Evikon PluraSens E2670-LEL Bedienungsanleitung

Evikon

Evikon PluraSens E2648-C2H4 Bedienungsanleitung

Evikon

Evikon PluraSens E2648-ETO Bedienungsanleitung

Evikon

Evikon PluraSens E2648-NH3-S Bedienungsanleitung

Evikon

Evikon E2660-CO-CO2 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung