EXFO bv10 Bedienungsanleitung
Installation Guide
Performance Endpoint Unit
BV10
ii BV10
Copyright © 2010–2014 EXFO Inc. All rights reserved. No part of this
publication may be reproduced, stored in a retrieval system or transmitted
in any form, be it electronically, mechanically, or by any other means such
as photocopying, recording or otherwise, without the prior written
permission of EXFO Inc. (EXFO).
Information provided by EXFO is believed to be accurate and reliable.
However, no responsibility is assumed by EXFO for its use nor for any
infringements of patents or other rights of third parties that may result from
its use. No license is granted by implication or otherwise under any patent
rights of EXFO.
EXFO’s Commerce And Government Entities (CAGE) code under the North
Atlantic Treaty Organization (NATO) is 0L8C3.
The information contained in this publication is subject to change without
notice.
Trademarks
EXFO’s trademarks have been identified as such. However, the presence
or absence of such identification does not affect the legal status of any
trademark.
Units of Measurement
Units of measurement in this publication conform to SI standards and
practices.
December 4, 2014
Version number: 5.0.0.1
Certification Information
BV10-100 and BV10-1000 iii
Certification Information
North America Regulatory Statement
This unit was certified by an agency approved in both Canada and the
United States of America. It has been evaluated according to applicable
North American approved standards for product safety for use in Canada
and the United States.
Electronic test and measurement equipment is exempt from FCC part 15,
subpart B compliance in the United States of America and from ICES-003
compliance in Canada. However, EXFO Inc. makes reasonable efforts to
ensure compliance to the applicable standards.
The limits set by these standards are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the user guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
European Community Declaration of Conformity
An electronic version of the declaration of conformity for your product is
available on our website at www.exfo.com. Refer to the product’s page on
the Web site for details.
Laser
This product complies with 21 CFR 1040.10 except for deviations pursuant
to Laser Notice No. 50, dated June 24, 2007 and with IEC/EN 60825-1.
iv BV10
Installation Instructions
Installation Instructions
This document describes the basic steps for installing the BV10. Refer to
the BV10 user guide for more information.
Contents
Page
Getting Started 1
Installing the BV10 in a Rack 1
Connecting the Power 2
Physical Interfaces, LEDs, and Buttons 7
BV10 Models 7
Port Availability on BV10 8
Connecting the TEST Port Interface 8
Connecting the Management Interfaces 10
LEDs 12
RESET and DEFAULT Buttons 13
BV10-100 and BV10-1000 1
1 Getting Started
Installing the BV10 in a Rack
The BV10 can be mounted in a rack using the rack mount accessory kit
(ordered separately). The accessory kit shelf holds up to four BV10.
To install the BV10 in a rack:
1. Attach the brackets of the supplied shelf unit to your rack using the
supplied screws.
2. If cables have been attached to the BV10, disconnect all of them as
well as the ground lug from the unit.
3. Slide the unit into the desired slot from front to back.
4. With the unit completely inserted into the slot, tighten the thumb screw
at the back of the unit.
5. Connect all cables and the ground lug, as explained in the next
sections.
Getting Started
2BV10
Connecting the Power
Connecting the Power
The BV10 is available with either an AC power supply, DC +24 V connector,
or DC –48 V connector.
As soon as the BV10 is connected to a live power supply, the POWER LED
turns on. If the POWER LED does not turn on, there is a power failure at the
source or the unit is damaged. The STATUS LED indicates whether or not
the unit is ready for use. If the STATUS LED is off the unit is booting up. If it
is green or red the unit has booted (refer to STATUS on page 12).
Getting Started
BV10-100 and BV10-1000 3
Connecting the Power
Grounding the BV10
The BV10 is equipped with a ground lug and hardware attached to the
back of the unit. The grounding hardware consists of a washer with
external teeth facing the unit and a locking nut. You will need to supply a
#12 AWG wire.
To ground the BV10:
1. Loosen the locking nut on the grounding lug.
2. Using a #12 AWG wire, twist the wire around the lug so that it is
touching the flat surface of the washer. The wire must be twisted
between the washer and the locking nut.
3. Tighten the locking nut.
4. Connect the other end of the wire to the ground distribution network.
WARNING
The BV10 DC version is intended to be grounded. Ensure that the unit is
connected to earth ground during normal use.
AC unit ground
lug and hardware
DC unit ground
lug and hardware
Getting Started
4BV10
Connecting the Power
Connecting the BV10 using an AC/DC Power
Source
The typical output voltage of the external brick AC power supply is 9 V DC.
To connect the BV10 to an AC power source:
1. Connect the supplied AC power cord to the AC/DC adapter and the
other end to an AC wall outlet.
2. Connect the other end of the power supply to the DC barrel power
connector on the BV10.
Connecting the BV10 using a DC Power Source
The BV10 DC version is equipped with either +24 V DC or –48 V DC
connector.
To connect the BV10 to a DC power source:
1. Using 14-16 AWG copper insulated wires and the supplied connector,
insert the two stripped wires into the connector and tighten the screws
firmly. Either use non-stranded wire or crimp a ferrule onto the wire.
Be sure to respect the polarity.
The positive supply wire lead must be on the right side of the
connector and the negative supply wire on the left side.
WARNING
Powering a BV10 +24 V DC unit with a –48 V power source will
permanently damage the unit. The +24 V input range is 20-32 V.
Powering a BV10 –48 V DC unit with a +24 V power source will
permanently damage the unit. The –48 V input range is –40 to –72 V.
Getting Started
BV10-100 and BV10-1000 5
Connecting the Power
The following figures show the –48 V and +24 V DC units.
-
-
2. Connect the plug to one of the two DC input connectors on the BV10
unit and tighten the screws firmly.
–48 V DC Unit
Supplied connector
Negative (–) supply wire lead on the left
Positive (+) supply wire lead on the right
+24 V DC Unit
Supplied connector
Negative (–) supply wire lead on the left
Positive (+) supply wire lead on the right
Getting Started
6BV10
Connecting the Power
3. Connect the other end of the wires to the DC power source.
4. To add a redundant DC power source on the BV10, repeat step 1
through step 3.
CAUTION
The DC input feeds to the equipment must be protected by 20 A rated
maximum breaker provided as part of the building installation.
Permanently connected equipment must have a switch or
circuit-breaker for disconnection. If the switch is not part of the kit:
Include a switch or circuit-breaker in the installation.
The switch must be located easily, and placed near the equipment.
The switch must be specified as the disconnecting device for the
equipment.
WARNING
To avoid serious injuries as well as irreparable damages to your unit,
ALWAYS TURN OFF BOTH DISCONNECT DEVICES BEFORE OPENING OR
SERVICING THE UNIT.
Andere Handbücher für bv10
1
Inhaltsverzeichnis
Andere EXFO Prüfgeräte Handbücher
EXFO
EXFO MaxTester 630G Bedienungsanleitung
EXFO
EXFO Power Blazer Bedienungsanleitung
EXFO
EXFO EX Series Bedienungsanleitung
EXFO
EXFO FVA-600 Bedienungsanleitung
EXFO
EXFO Power Blazer Bedienungsanleitung
EXFO
EXFO NetBlazer Series Bedienungsanleitung
EXFO
EXFO MAX-800 Series Bedienungsanleitung
EXFO
EXFO Optical Explorer OX1 Betriebsanleitung
EXFO
EXFO EX10 Bedienungsanleitung
EXFO
EXFO AXS-200/850 Bedienungsanleitung
EXFO
EXFO EPM-500 Bedienungsanleitung
EXFO
EXFO FTBx-88000 Series Bedienungsanleitung
EXFO
EXFO ConnectorMax MFS-12 Bedienungsanleitung
EXFO
EXFO ETS-1000 Bedienungsanleitung
EXFO
EXFO MAX-700 Bedienungsanleitung
EXFO
EXFO IQS-2150 Bedienungsanleitung
EXFO
EXFO FOT-930 MaxTester Bedienungsanleitung
EXFO
EXFO MaxTester Max-610 Bedienungsanleitung
EXFO
EXFO RTU-2 Bedienungsanleitung
EXFO
EXFO MaxTester 630G Bedienungsanleitung
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung