EXFO ConnectorMax MFS-12 Bedienungsanleitung



14 To perform the three captures, the movable part of the inspection tip is moved with the trigger. A

capture is made for each position.

Inspection tip (movable part)

Indicates the position to follow to

perform the 3 captures.

Trigger

The icons on screen indicate when you can change the position of the inspection tip and the status

LED as well. When the LED is blue and stops flashing, you can perform a capture.

14a Using the trigger, slide the movable part of the inspection tip to perform each capture.

14b Once you are satisfied with the inspection, tap .

Press the Fiber Inspection Probe capture control button.

15 When the last capture is performed, the analysis starts immediately.

The polarity of a multifiber patchcord refers to how the fibers are linked between the transmitting (Tx) and

receiving (Rx) connectors. The application refers to the TIA 568 standard which defines three polarity types: A,

B, and C. Any other fiber mappings in a multifiber patchcord will result in an unknown polarity type.

Analyzing Polarity Results

The results are available as an image or in

a detailed table.

A fail status either on the inspection of the

connector, the polarity, or continuity will

result in a global fail status.

Discontinuity icon

Analyzing Inspection Results

The image overlay indicates the inspection

status of the connector per zone.

Following the analysis, an image of the identified elements and defects is overlayed on the connector image.

The color of the circles indicates the inspection status of the connector per zone. Red refers to a fail status

whereas green to a pass.

Analyzing Continuity Results

The continuity in a fiber refers to the ability for each fiber of a multifiber patchcord to conduct the light from one

end to the other. With the Fiber Inspection Probe at the receiving end, it is possible to determine on which fibers

discontinuities are found ( ).

Discontinuities

found on fibers

are displayed in

red.

MFS-12/MFS-24

ConnectorMax MPO Test Solution (iOS)

The Multifiber Source (MFS) produces a light pattern that, once injected into a fiber, is detectable by the EXFO’s

Fiber Inspection Probe equipped with an MPO tip (12 or 24 fibers). With the MFS, the probe will test the

continuity and polarity of the link under test in addition to performing the connector inspection.

Only the probes identified as MF-Ready allow you to use the MFS or the MPO tip.

Installing the FIP Nozzle

You need to install the removable nozzle and the inspection tip on the probe before you start working. The

nozzle is interchangeable and you can insert it key up or key down. To facilitate the installation process, install

the removable nozzle on the inspection tip first.

1Install the removable nozzle (key up or key down) on the metal rod of the inspection tip and align the

key of the nozzle with the notch of the inspection tip until you feel it click in place.

Inspection tip

Removable nozzle

MF-Ready probe

Retaining nut

Tighten the retaining

nut clockwise.

To change the nozzle,

untighten,

counterclockwise.

Quick Reference Guide

Printed in Canada (2018-11)

P/N: 1074619 Version: 1.0.0.1 For more information,

refer to the user guide.

3Install the inspection tip on the MF-Ready probe by aligning the key of the probe with the notch of the

inspection tip.

Inspection tip (movable part)

MF-Ready probe

Trigger 4Tighten the retaining nut clockwise.

Note: If you cannot see the notch of the inspection tip, slide the movable part of the inspection tip with the

trigger towards the nozzle.

Setting up the Multifiber Source Inspecting Multiple Fiber Ends

When you connect an MF-Ready probe to your smart device, you can view and inspect multiple fiber ends right

away. This type of inspection requires three captures. As soon as the third capture is performed, the analysis

process starts. If you only want to inspect a connector without testing polarity and continuity, ensure that the

MFS is turned off before proceeding. Otherwise, the light emitted by the MFS could be mistaken for dirt which

would result in an erroneous fail status.

In Live Video mode, tap the Test Configuration

row.

The MFS allows you to test continuity and polarity (based on A, B, or C polarity types) on multifiber links

terminated with MPO connectors. Its design includes a cable management system that allows you to use a

patchcord as connector savers for the MPO connectors on the source.

1Connect the APC connector of the

patchcord to the adapter.

On/Off button with power LED

Battery level indicator

If you are using a

patchcord having a

single connector, you

can connect it to any of

the two adapters. With

an MPO-24 split (Y)

patchcord, you must

connect each of its ends

to one of the adapters.

4Open the dust cap and connect the DUT to the appropriate adapter according to the

connections you made in the previous step. If you have connected an MPO-24 split

patchcord, you will have to connect the DUT, in turn, to each of the two adapters.

5Connect the other end of the DUT

to the removable nozzle of the

probe.

Secure the

patchcord in

place by

wrapping it

around the unit.

11 Select Multiple Fiber Connector,

and then set the other parameters

according to your needs.

Key orientation of the connector (key up

or key down, depending on the position

of the nozzle)

Fiber configuration of the connector you

use

To validate the

cleanliness of the fibers

of the connector

To stop the analysis as soon as a fail status is detected

on a fiber

Type of expected polarity for your tests

Tap the arrow.

Select a test configuration to use for your test.

13 If the connector is dirty, remove it from the probe, clean it and reinspect it.

Note: If you are working with an FIP-435B, you can

activate the auto focus feature using the down

arrow in live video mode.

1Turn on the probe.

2Ensure the Wi-Fi is activated on your smart device.

3Go to the device Settings and select Wi-Fi.

4Select the wireless probe you want to work with.

5Start the ConnectorMax2 Mobile application.

Tap Start Live Video.

7Insert the connector into the removable nozzle you have already installed.

Tap the Measurement Name row to configure

the automatic file naming.

Dieses Handbuch passt für folgende Modelle

Andere EXFO Prüfgeräte Handbücher

EXFO

EXFO MaxTester 630G Bedienungsanleitung

EXFO

EXFO FTB-200 Bedienungsanleitung

EXFO

EXFO EX10 Bedienungsanleitung

EXFO

EXFO MaxTester series Bedienungs- und Wartungshandbuch

EXFO

EXFO FTBx-88000 Series Bedienungsanleitung

EXFO

EXFO CT440 Series Bedienungsanleitung

EXFO

EXFO Fiber Guardian FG-750 Bedienungsanleitung

EXFO

EXFO FVA-60B Bedienungsanleitung

EXFO

EXFO MaxTester series Bedienungsanleitung

EXFO

EXFO AXS-200/610 Bedienungsanleitung

EXFO

EXFO AXS-200/635i Bedienungsanleitung

EXFO

EXFO ARU-100 Bedienungsanleitung

EXFO

EXFO CT440 Series Bedienungsanleitung

EXFO

EXFO FTB-8500 Series Bedienungsanleitung

EXFO

EXFO MaxTester 700 Bedienungsanleitung

EXFO

EXFO Power Blazer Bedienungsanleitung

EXFO

EXFO FTB-7000B Bedienungsanleitung

EXFO

EXFO MAX-800 Series Bedienungsanleitung

EXFO

EXFO FTB-610 Bedienungsanleitung

EXFO

EXFO FTB-700 Series Bedienungsanleitung

EXFO

EXFO MaxTester 635 Bedienungsanleitung

EXFO

EXFO BRT-320A Bedienungsanleitung

EXFO

EXFO CableSHARK P3 Bedienungsanleitung

EXFO

EXFO MaxTester 630G Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung