Extang Trifecta 2.0 Bedienungsanleitung
3 1 9 2 0 7 0 0 - 3 0
Item No. 31920700-30 01.18 DD
Extang, Corp., 2017. Printed in USA
TARP REMOVAL AND REPLACEMENT
Tools Required: Closed end wrench, to be used as a round edged instrument.
3/16” Hex Wrench
Rubber Mallet
Remove the tonneau from
the vehicle and place it on
its side as shown to begin
removing the cover from
one side.
12
3
Tarp Removal
Locate one of the hinge areas of the cover. Using a rounded instrument, (the
closed end wrench), tuck behind the plastic strip and begin prying the retaining
strip out of its track. Do Not use anything sharp or pointed as tarp
damage may occur.
Continue removing the plastic strip from the one side.
Place the tonneau on a clean, at surface and nish detaching the cover from the side rails and corners.
Repeat the procedure for the other side.
Remove one side of the frame. To do this you will need the 3/16” Hex wrench. Loosen but do not remove
the fastener from the tail rail.
The side rail should now slide out of the corners and bows. Repeat the procedure on the other side.
4
5
6
Tarp Removal
CAB RAIL
TAIL RAIL
Tarp Removal
Tarp Install
The nal step is to detach the cab rail and tail rail. The retaining strip does not slip out like the side rails.
They must be slid along the entire length of the tarp.
Begin with the tail rail and insert the retaining
strip into the rail. Continue to slide the rail
until it is centered in the tarp.
The Trifecta 2.0 badge is sewn in and marks
the rear corner.
Slide the retaining strip into the cab
rail, paying attention to center the
tarp. The two front buckles insert
outside of and around the tarp.
Check and remove any slivers or
burrs that may have come from the
retaining strip sliding along both the
cab and tail rails.
7
1
2 3
CAB END
TAIL END
SLIDE NUT
Install the side rail assemblies.
Beginning at the rear corner insert the slide nut
into the c-channel portion of the tail rail,
followed by the rear corner.
Secure the cap screw with the 3/16” hex wrench.
4
Tarp Install
Insert the bows in the following order:
A. Rear (tailgate) bow (with tail clamps) into the u-shaped brackets.
B. Insert the bow (with the straps attached) into the plastic post bracket.
C. Insert the next bow (4 bow systems only) in the same manner as the previous bow (B).
D. The front (cab) bow is installed into the u-shaped brackets like the Rear (tailgate) installation.
5
Note: The cover may seem loose at this point. The tarp tension will increase when the sides are attached.
ABCD
A
C
Attaching to the sides.
Insert the retaining strip into the side rail as follows:
A. Begin at one corner inserting the strip into
the rail until you reach halfway.
B. Start at the opposite side and corner and insert
the strip along that rail.
C. Return to rst side and nish inserting the strip
and the nal corner.
6
Tarp Install
B
Inhaltsverzeichnis
Andere Extang Autozubehör Handbücher
Extang
Extang Classic Platinum Montageanleitung
Extang
Extang Solid Fold 2.0 Montageanleitung
Extang
Extang Trifecta Montageanleitung
Extang
Extang Classic Platinum Bedienungsanleitung
Extang
Extang Express Tonno Montageanleitung
Extang
Extang Trifecta 2.0 Montageanleitung
Extang
Extang CLASSIC PLATINUM Montageanleitung
Extang
Extang CLASSIC PLATINUM BLACKMAX TUFF TONNO III & Saber TONNO... Montageanleitung
Extang
Extang e-MAX TONNO Montageanleitung
Extang
Extang CLASSIC PLATINUM & BLACKMAX 7920 Montageanleitung
