Extech Instruments DL160 Bedienungsanleitung

User's Guide

Dual Input True RMS AC

Voltage/Current Datalogger

Model DL160 / DL162

Shop for Extech products online at: 1.877.766.5412

www.PowerMeterStore.com

DL160-EU-EN-V1.2-4/12

Introduction

Congratulations on your purchase of this Dual Input Voltage / Current datalogger. With this meter,

you can monitor and log data (Voltage/Voltage, Current/Current or Voltage/Current) over long

periods of time and then easily transfer the data to a pc for viewing and evaluation. The LCD

display provides real time data, Max/Min data and time information. This meter is shipped fully

tested and calibrated and, with proper use, will provide years of reliable service.

Safety

Warning!

•Do not attempt to make measurement in flammable gaseous areas!

•When testing a non-insulated cable, pay attention to avoid short circuits.

•Do not attempt to use the instrument when your hand is wet!

•Do not input over range during measurements.

•Never open the battery cover during measurements.

•Stop using the instrument when there is any structural defect or exposed metal parts.

•Do not install substitute parts or make modifications on the meter.

•Never replace the battery in moist areas.

•Ensure the meter is disconnected and switch off before opening the battery cover to replace

the battery.

•Do not attempt to place the instrument in high vibration areas.

•Do not expose the meter to direct sunlight, high temperature and high moisture environment.

•Switch off the meter after use. Remove the AAA batteries when the meter will be stored for a

period of time..

•When cleaning, do not use abrasives or solvents on the meter, use a damp cloth and mild

detergent only.

Shop for Extech products online at: 1.877.766.5412

www.PowerMeterStore.com

DL160-EU-EN-V1.2-4/12

Description and Button Functions

1. LCD Description

Auto power off (does not apply when recording), the

meter will automatically shuts off after 5mins without any

button presses.

REC: Recording status. After the record mode is set up by the

software, press the START/STOP button for more than 4

seconds to begin recording. This icon will be displayed

and indicates the meter is recording data. Press the same button again for more than 4

seconds to stop recording.

Record until full is selected. When the memory is full, the datalogger will stop recording.

Continuous recording is selected. When the memory is full, the data will overwrite the

oldest data.

FULL Memory full and recording has stopped.

Battery status, when completely filles in (black) the battery power is full. When there is

only one section filled in, the battery is exhausted and should be replaced with a new

one.

2. AC adaptor Jack

3. ON/OFF Button

4. MAX/MIN : Press the button one time to display the MAX (maximum)

reading . Press again to display the MIN (minimum) reading. A third

press will exit MAX/MIN mode. The meter will automatically exit

MAX/MIN mode in 10 seconds if no button is pressed.

5. CH Input Jacks: Insert the current or voltage sensor to these ports to

measure and record the data.

6. CHANNEL: Select the channel for display on the LCD

7. START/STOP: After the datalogger is setup from the software, press

the START/STOP button for 4 seconds to begin recording. Press the button again for 4 seconds

to stop recording. Recording cannot be started again until the data is downloaded to the software.

8. USB Port

9. AC Current Clamp Jaw: Clamp the jaws around a single

conductor for AC current measurements to 200A

10. Jaw Opening Trigger:

11. CH Plug:

12. AC Voltage Probes or Alligator clips

13. Voltage module

14. CH Plug

910 11

Shop for Extech products online at: 1.877.766.5412

www.PowerMeterStore.com

DL160-EU-EN-V1.2-4/12

Operation

1. Install 4 fresh AAA batteries or connect the AC adaptor.

2. Set-up the datalogger using the software provided.

3. Connect the voltage test leads or the current probes to the AC source to be measured.

4. Press and Hold the START/STOP button for four seconds to start recording. The “REC” icon

will appear in the display indication that recording has begun.

5. Press and Hold the START/STOP button for four seconds to stop recording. The “REC” icon

will disappear from the display.

6. Remove the probe, connect the datalogger to a PC and use the supplied software to download

the data.

Note: If the clock does not set to the correct time, replace the 3V button battery.

You, as the end user, are legally bound (Battery ordinance) to return all used batteries and

accumulators; disposal in the household garbage is prohibited!

You can hand over your used batteries / accumulators at collection points in your community

or wherever batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle.

Software Introduction

1. Place the CD in the drive and then follow the on-screen installation instruction.

2. After the software is installed, keep the CD in the drive and connect the datalogger to the PC

by the USB cable.

3. A USB Driver installation window will pop-up. Follow the directions to install the driver.

System Required:

Windows 2000 or Windows XP or Vista

Minimum Hardware Required:

PC or NoteBook with Pentium 90MHz or higher 32 MB RAM ;

At least 7 MB byte hard disk space available to install Datalogger USB software.

Recommended display resolution 1024X768 with High Color(16 bit).

Software Operation

The Software operation is described in the HELP file located on the software disk.

Shop for Extech products online at: 1.877.766.5412

www.PowerMeterStore.com

DL160-EU-EN-V1.2-4/12

Specifications

Display Multi-function LCD

Maximum data points 256,000 values

Channels dual channel, TRMS AC Voltage or Current

Sample rate 1s to 24h selectable

Analysis software 2000/XP/ Vista

Data output USB port

Current Clamp Jaw opening 12.7mm (0.5”)

Open input indication "LO" appears on the LCD

Low battery indication Empty battery symbol appears on the LCD

Power supply 4 AAA Batteries and 1 CR 3V memory button battery (CR2032 or

equivalent)

Battery life 5 days (approximately)

AC Adaptor 9V, 0.5A

Standards

, CAT III 600V, for inside use, maximum height 2000 meters

Operating Temperature 0 to 50°C, 32 to 122°F

Operating Humidity <70% RH

Storage temperature: -20°C to 60°C (-4°F to 140°F)

Storage Humidity < 80% relative humidity.

Dimensions 114 x 63 x 34mm” (4.5 x 2.5 x 1.3)

Weight 248g. (8.7oz)

Function Range Accuracy

Voltage (40Hz to 1kHz) 10VAC to 600.0VAC ±2.0%±1V

Current (50/60Hz) 10A to 200.0A ±2.0%±1A

www.extech.com

Shop for Extech products online at: 1.877.766.5412

www.PowerMeterStore.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extech Instruments Datenlogger Handbücher

Extech Instruments

Extech Instruments RTH20 Bedienungsanleitung

Extech Instruments

Extech Instruments TM500 Bedienungsanleitung

Extech Instruments

Extech Instruments 42280A Bedienungsanleitung

Extech Instruments

Extech Instruments VB300 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT20 Bedienungsanleitung

Extech Instruments

Extech Instruments 451126 Bedienungsanleitung

Extech Instruments

Extech Instruments DL150 Bedienungsanleitung

Extech Instruments

Extech Instruments DL150 Bedienungsanleitung

Extech Instruments

Extech Instruments 380340 Bedienungsanleitung

Extech Instruments

Extech Instruments 451126 Bedienungsanleitung

Extech Instruments

Extech Instruments EA80 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT10 Bedienungsanleitung

Extech Instruments

Extech Instruments 475040-SD Bedienungsanleitung

Extech Instruments

Extech Instruments DL160 Bedienungsanleitung

Extech Instruments

Extech Instruments 381395 Bedienungsanleitung

Extech Instruments

Extech Instruments SD910 Bedienungsanleitung

Extech Instruments

Extech Instruments SD800 Bedienungsanleitung

Extech Instruments

Extech Instruments 42582 Bedienungsanleitung

Extech Instruments

Extech Instruments 407760 Bedienungsanleitung

Extech Instruments

Extech Instruments 382100 Bedienungsanleitung

Extech Instruments

Extech Instruments THD5 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL2004 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT20 Bedienungsanleitung

Extech Instruments

Extech Instruments 42280 Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung