Extech Instruments SD800 Bedienungsanleitung

User's Guide

CO2/Humidity/Temperature Datalogger

Model SD800

SD800-EU-EN- V2.4 1/13

Introduction

Congratulations on your purchase of the Extech SD800 CO2/Temperature/Humidity Datalogger.

This meter measures, displays, and stores CO2, temperature and relative humidity readings. Data is

stored on a SD card for transfer to a PC. This meter is shipped fully tested and calibrated and, with

proper use, will provide years of reliable service

Features

LCD simultaneously displays Carbon Dioxide, Temperature and Relative Humidity

Datalogger date/time stamps and stores readings on an SD card in Excel® format for easy

transfer to a PC

Selectable data sampling rate: 5, 10, 30, 60, 120, 300, 600 seconds

Product Description

1. Humidity/Temperature Sensor

2. Humidity Display

3. Temperature Display

4. CO2 Display

5. LOG (ENTER) button

6. SET button

7. AC adaptor socket

8. CO2 probe socket

9. ▲(TIME) button

10. ▼button

11. Reset button

12. RS-232 output

13. SD memory card socket

14. CO

probe

15. CO

plug

Note: Battery Compartment and Tilt Stand are located on the back of the meter.

SD800-EU-EN- V2.4 1/13

Operation

Setup

1. Connect the CO2probe to the datalogger by inserting the plug into the connector on the bottom

of the datalogger.

2. Connect the AC adaptor to the datalogger by inserting the plug into the connector on the

bottom of the datalogger.

3. Insert the 6 AAA batteries into the battery compartment. Without these batteries installed, the

real time clock will reset every time the ac adaptor is disconnected.

Datalogging

1. Open the left side door and insert a formatted SD card

Note: The SD card should be at least 1GB in capacity (4GB to 16GB recommended)

Note: Do not use memory cards formatted by other meters or cameras. Use the SD card

formatting procedure under the advanced features section of this manual to correctly

format the card.

Note: The internal clock must be set to the correct time See the advanced features section of

this manual to set the clock.

Note: The default data structure uses a decimal point “.” as the numeric decimal indicator. See

the advanced features section of this manual to change this to a comma “,”.

Note: If the SD memory card is not installed, “EMPTY” will appear in the display

Note: Displayed error messages:

The memory card is full or there is a problem with the card

The battery is low.

The SD card is not inserted

2. Press the LOGGER button for >2 seconds to begin logging. “DATALOGGER” will appear in the

display and the meter will beep each time the data is recorded (if the beeper is enabled).

3. To stop datalogging, press the LOGGER button for >2 seconds. “DATALOGGER” will change

to “DATA” and the meter will count down through the recorded data.

NOTE: To avoid corrupting data, do not remove the memory card without properly ending the

record function.

Time/Date/Sample Rate Check

Press and Hold the TIME button for >2 seconds and the display will cycle through the date, time and

sample rate information.

CArd

LobAt

CH-

CArd

SD800-EU-EN- V2.4 1/13

SD Card Data Structure

1. When the SD card if first inserted into the datalogger the folder CHA01 is created.

2. The first datalogging session will then create a file CHA01001.XLS. All data will be saved to

this file until the number of columns reaches 30,000.

3. After 30, 000 columns a new file, CHA01002.XLS is created. This is repeated every 30,000

columns until CHA01099.XLS. At this point a new folder, CHA02 is created and the process is

repeated. CHA10 is the final folder.

Transferring Data to a PC

1. Remove the memory card from the datalogger and plug it into the SD card slot on the PC.

2. Launch Excel® and open the data file on the memory card from within the spreadsheet

program. The file will appear similar to the figure below.

SD800-EU-EN- V2.4 1/13

Advanced Settings

The SET function is used to accomplish the following:

Format the SD memory card

Set the date and time

Set the sampling time

Set the beeper sound ON/OFF

Set the SD card Decimal character

Select the Temperature units

Set the RS232 data output ON/OFF

Set CO2height compensation in meters

Set CO2height compensation in feet

1. Press and Hold the SET button for >2 seconds to enter the setting mode. The first function (Sd

F) will appear in the display. Press the SET button to step through the seven functions. Use the

▲and ▼buttons to adjust the selected function. Use the “LOGGER” button to step through

fields within a function. In the SET mode, if no button is pressed within 5 seconds the logger

will revert to the standard mode.

2. Sd F – Format the SD card. Press the ▲button to select yES or no. For yES, press the Enter

button to format the card and erase all existing data.

3. dAtE – Set the date and time. Press the ▲or ▼buttons to adjust the selected field. Press the

Enter button to store the value and to step through the various fields.

4. SP-t – Set the sample rate. Press the ▲button to select the desired sample rate and press

Enter to store the selection. The selections are: 5, 10, 30, 60, 120, 300, 600 seconds and

AUTO. In AUTO, the data will be stored every time there is a temperature change of >1

degree, > 1 %RH or > 50 ppm.

5. bEEP - Set the beeper ON or OFF. Press the ▲button to select ON or OFF and press Enter to

store the selection.

6. dEC - Set the SD card Decimal character. Press the ▲button to select USA (decimal) or Euro

(comma) and press Enter to store the selection.

7. t-CF - Set the Temp. unit to °F or °C and press ENTER to store the selection.

8. rS232 - Set the RS232 data output ON/OFF. Press the ▲button to select ON or off and press

Enter to store the selection

9. HIgh- – Set the height compensation for CO2in meters. Press the ▲or ▼buttons to adjust the

selected field to the height (altitude) of the measurement site. This adjustment will improve

measurement accuracy.

10. HIghF - Set the height compensation for CO2in feet. Press the ▲or ▼buttons to adjust the

selected field to the height (altitude) of the measurement site. This adjustment will improve

measurement accuracy.

11. ESC – Exit the setting mode. Press the SET button to return to normal operation.

System RESET

If a condition appears where the CPU does not respond to keystrokes or the meter seems frozen,

press the RESET button on the side of the datalogger (use a paper clip or similar pointed object) to

return the meter to a working state.

RS232 Interface

A serial output is provided to link the meter to a PC’s serial port. Call Technical Assistance for more

information on this interface.

SD800-EU-EN- V2.4 1/13

Battery Warning, Installation and Replacement

1. When the AC adaptor is not connected and the low battery icon appears in the display,

the batteries are weak and should be replaced. To replace or install batteries, remove the

Philips head screw that secures the rear battery cover and lift off the cover.

2. Replace the six AAA batteries (use alkaline heavy duty type), observing polarity

3. Replace and secure the cover.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries

/ accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Specifications

DCL)”0.2x4.2(mm05x06yalpsiD

Measurement sensors Temperature: Internal sensor

rP:ytidimuHevitaleR ecision capacitance type

CO2: NDIR

CO2Response Time <2 min to 63% of final reading typical

Memory Card SD memory card, 1 GB to 16 GB.

Datalogger Sampling Time 5/10/30/60/120/300/600 seconds or Auto.

Temperature Compensation Automatic

Display update rate Approx. 1 second

Data Output RS 232

Operating Temperature 0 to 50°C (32 to 122°F)

Operating Humidity Less than 90% RH

Power Supply 9V AC adaptor.

Six (6) AAA (UM4) 1.5 V batteries for clock backup

)bl53.0(g851eborP.).sbl35.0(g042:reteMthgieW

Dimension Meter: 132 x 80 x 32mm (5.2 x 3.1 x 1.3”)

Probe: 132 x 38 x 32mm (5.2 x 1.5 x 1.3”)

Range Resolution Accuracy

0.0 to 50.0 °C 0.1°C ± 0.8°C

Temperature

32.0 to 122.0°F 0.1°F ± 1.8°F

HR%4±%07ot01

Relative Humidity

70 to 90% 0.1% ± (4% of reading + 1% RH)

≤mpp04±mpp0001

>1000 to ≤gnidaerfo%5±:mpp0003

CO2

>3000ppm

1ppm

±250ppm typical

Note: Above specification tests under the environ ment RF Field Strength less than 3 V/M & frequency

less than 30 MHz only.

www.extech.com

more info for Extech SD800

Phone: 01235 838 555

Email: cs@airconcern.co.uk

Web: www.airconcern.co.uk

Air Concern Ltd, Building 173 Curie Avenue Harwell Didcot, Oxfordshire

Inhaltsverzeichnis

Andere Extech Instruments Datenlogger Handbücher

Extech Instruments

Extech Instruments DL160 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL2004 Bedienungsanleitung

Extech Instruments

Extech Instruments RTH10 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT35 Bedienungsanleitung

Extech Instruments

Extech Instruments RHT20 Bedienungsanleitung

Extech Instruments

Extech Instruments THD5 Bedienungsanleitung

Extech Instruments

Extech Instruments SD900 Bedienungsanleitung

Extech Instruments

Extech Instruments DL150 Bedienungsanleitung

Extech Instruments

Extech Instruments SD700 Bedienungsanleitung

Extech Instruments

Extech Instruments 451126 Bedienungsanleitung

Extech Instruments

Extech Instruments 381395 Bedienungsanleitung

Extech Instruments

Extech Instruments TM500-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments RHT20 Bedienungsanleitung

Extech Instruments

Extech Instruments TH10 Bedienungsanleitung

Extech Instruments

Extech Instruments VB300 Bedienungsanleitung

Extech Instruments

Extech Instruments 42582 Bedienungsanleitung

Extech Instruments

Extech Instruments DL160 Bedienungsanleitung

Extech Instruments

Extech Instruments 380340 Bedienungsanleitung

Extech Instruments

Extech Instruments 407760 Bedienungsanleitung

Extech Instruments

Extech Instruments DL150 Bedienungsanleitung

Extech Instruments

Extech Instruments Quick Start Bedienungsanleitung

Extech Instruments

Extech Instruments PQ3470-2 Bedienungsanleitung

Extech Instruments

Extech Instruments TH10 Bedienungsanleitung

Extech Instruments

Extech Instruments TM500 Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung