Extech Instruments 380580 Bedienungsanleitung

User’s Guide

Model 380580

Battery Powered

Milliohm Meter

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Back to the Extech 380580 Product Page

Version 2.0 1/05

Introduction

Congratulations on your purchase of Extech’s Model 380580 Battery Powered Milliohm

Meter. This device offers five resistance ranges with resolution as low as 0.1mΩ. The 4-wire

Kelvin clip connection ensures optimum accuracy. Typical applications include transformer,

motor coil, and PC Board resistance measurements. This professional meter, with proper

care, will provide years of safe reliable service.

Specifications

General Specifications

Display 1.0" (25 mm) LCD (1999 counts)

Measurement terminals 4-Terminal Kelvin type

Measurement Range Five ranges (see listing below)

Sampling Time Approximately 3 times per second

Over input indication Indication of "1 - - -"

Operating Temperature 5ºF to 131ºF (-15ºC to 55ºC)

Operating Humidity <80% RH

Power Supply 8 x 1.5V AA Batteries

Weight 3.3 lbs (1.5kg)

Dimensions 9.8x7.5x4.3" (250x190x110 mm) with cover

Range Specifications

Range

Resolution Test

Current

Accuracy Open Circuit

Voltage

200.0mΩ0.1mΩ100mA ± 0.5% + 2 digits 4.2V

2000mΩ1mΩ100mA ± 0.5% + 2 digits 4.2V

20.00Ω0.01Ω10mA ± 0.5% + 2 digits 4.2V

200.0Ω0.1Ω10mA ± 0.5% + 2 digits 4.3V

2000Ω1Ω1mA ± 0.5% + 2 digits 4.4V

International Symbols

This symbol, adjacent to another symbol or terminal, indicates the user must

refer to the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use,

hazardous voltages may be present

Double insulation

Version 2.0 1/05

Meter Description

1. Current Terminals

2. Potential Measurement Terminals

3. LCD Display

4. Start/Stop Test Button

5. Range Select/Power Switch

6. LED Error Lights

• No Test/Over Temperature

• RPVoltage Regulation

• RCCurrent Regulation

7. Current/Range Table

Leads

Current Leads- Banana plug to alligator clip

C1- Green

C2- Blue

Voltage Potential Leads- Banana plug to alligator clip

P1- Red

P2- Black

Kelvin Clips- Banana Plugs (2) to Kelvin Clip

Red (P1) Green (C1)

Black (P2) and Blue (C2)

Measurement Considerations

1. Do not apply voltage to the meter input terminals. Meter damage may result.

2. Always insure that the circuit to be measured is switched OFF, isolated and

completely de-energized before connecting the test leads.

3. If the Over Temperature LED (NO TEST) indicator is lit, allow the instrument to

cool down before proceeding further.

4. The RCled indicates when the test current falls out of regulation. Selecting a higher

range may eliminate the condition.

5. The RPled indicates when the voltage on the device under test is too high.

Selecting a lower range may eliminate the condition.

6. If either the RCor RPled is on, the measurement may be in error.

7. The current terminals are fuse protected.

8. Keep the potential test leads as short as possible. Long leads may introduce noise.

9. When using the four separate alligator clip leads always place the current leads

outside the potential leads.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Version 2.0 1/05

Preliminary Checks

Current Regulation Check

1. Connect the current leads C1and C2to the meter.

2. Set the function switch to the 200.0mΩrange.

3. Momentarily press the TEST RPbutton. The meter

will intermittently beep and RC will light

4. Short the current leads C1to C2.

5. The RCLED should go off, indicating that the meter

is operating correctly.

6. Momentarily press the TEST RPbutton to stop the test

7. The meter will return to NO TEST status.

Voltage Measurement check

1. With the current test leads C1and C2 shorted,

connect and short the potential (voltage) leads P1

and P2.

2. Set the Function switch to the 200.0mΩposition.

The NO TEST status LED will light.

3. Momentarily press the TEST RPbutton. (the meter

will intermittently beep)

4. The display should indicate 00.0

5. Momentarily press the TEST RPbutton to stop the test.

The NO TEST status LED will light.

6. Remove the shorts from P1and P2, and C1and

C2and

7. Short the test leads P1to C1and P2to C2

8. The RPLED as well as the NO TEST status LED

should light indicating an over-voltage or over-range

9. Turn the rotary selector switch to OFF

Polarity check

1. Short the test leads P1to C2and P2to C1together.

2. Set the Function switch to the 200.0mΩposition.

3. The “-1“ negative indicator should appear in the

display.

Operation check

Use the Kelvin clips for this test

1. Short the all the leads (P1, P2,C2,C1) together.

The P1, P2,C2,C1 order is important.

2. Set the Function switch to the 200.0mΩ

position. The NO TEST status LED will light.

3. Momentarily press the TEST RPbutton. (the

meter will intermittently beep

4. The display should indicate near 00.0

(depending on the test clip connections) and

both RPand RCLEDs should remain off.

5. Momentarily press the TEST RPbutton to stop

the test.

Note: These tests can be performed on any range.

Version 2.0 1/05

Measurement Procedure

1. Select the desired measuring range on the meter. If the resistance of the device is

unknown, start with the highest range and work downward.

2. Clip the test leads onto the device under test. Note: When using the 4-wire/4

alligator clip test leads, it is recommended that the current test leads be outside of

the potential test leads (as shown in the diagram below).

3. For a short test duration of 10 seconds, press the TEST RPbutton for less than 2

seconds. This EnerSave™ feature can be used to conserve battery power.

4. For a long test duration of 60 seconds, press the TEST RPbutton for more than 3

seconds.

5. During the test, the meter will intermittently beep. At the end of the test or if the test

is stopped, “HOLD” will appear and the last reading will be “frozen” on the display.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Version 2.0 1/05

Measurement Principles

The test current flows through the resistance from the Current+ (C+) terminal to the

Current - (C-) terminal. The P+ and P- (POTENTIAL) terminals measure the voltage drop

across the device under test only, thus eliminating the lead and contact resistances. The

meter displays the resistance based on the test current and the measured voltage; refer to

the equation below:

Rx = Vx / Is

Where:

Vx is the voltage drop across the device under test;

Is is the test current;

Rx is the resistance of the device under test.

Thermal Effects

Temperature can have a significant effect on the performance of millohmeter due to the

temperature coefficient of the resistance under test and thermal EMF’s across dissimilar

conductors.

Most conductors have a large temperature coefficient of resistance

For example: 0.4%/°C for copper. A cooper conductor that has a resistance of 10.00m ohm at

20°C will increase to 10.40m ohm at 30°C. This should be taken into account..

A current going through a resistance will also elevate the temperature so duration of the test

can also change the resistance.

C+

C-

P+

P-

Current

Volts

Version 2.0 1/05

BATTERY INSTALLATION

WARNING: To avoid electric shock, disconnect the test leads from any source of voltage

before removing the battery cover.

1. Turn power off and disconnect the test leads from the meter.

2. Open the rear battery cover by removing two screws (B) using a slotted head

screwdriver.

3. Insert the batteries into battery holder, observing the correct polarity.

4. Put the battery cover back in place. Secure with the screws.

REPLACING THE FUSES

There are three fuses:

Power Supply Fuse

1. The power supply fuse is located in the battery compartment.

2. Remove the two screws to open the battery compartment.

3. Always use a fuse of the proper size and value.

Current Circuit Fuse

1. Fuse protection for the current terminals.

2. If the fuse is blown, the RCLED will stay on.

3. The fuse is located under the printed circuit board.

4. There are 4 mounting screws that have to be removed.

5. Two screws are located under the black feet on the bottom of the unit.

6. The other two screws are located in the battery compartment.

7. Remove the battery compartment door and the batteries to access these screws.

8. Always use a fuse of the proper size and value.

Potential Circuit Fuse

1. Fuse protection for the potential terminals.

2. If the fuse is blown, the RPLED will stay on.

3. The fuse is located under the printed circuit board.

4. There are 4 mounting screws that have to be removed.

5. Two screws are located under the black feet on the bottom of the unit.

6. The other two screws are located in the battery compartment.

7. Remove the battery compartment door and the batteries to access these screws.

8. Always use a fuse of the proper size and value.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Inhaltsverzeichnis

Andere Extech Instruments Messgerät Handbücher

Extech Instruments

Extech Instruments UV510-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments 406800 Bedienungsanleitung

Extech Instruments

Extech Instruments PQ3450-2-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments LT250W Bedienungsanleitung

Extech Instruments

Extech Instruments 42265 Bedienungsanleitung

Extech Instruments

Extech Instruments HD300 Bedienungsanleitung

Extech Instruments

Extech Instruments CO210 Bedienungsanleitung

Extech Instruments

Extech Instruments 475055 Bedienungsanleitung

Extech Instruments

Extech Instruments HDV7C-55-HD-1 Bedienungsanleitung

Extech Instruments

Extech Instruments 433201A Bedienungsanleitung

Extech Instruments

Extech Instruments PQ3350 Bedienungsanleitung

Extech Instruments

Extech Instruments 380976-K Bedienungsanleitung

Extech Instruments

Extech Instruments CO10 Bedienungsanleitung

Extech Instruments

Extech Instruments MO265 Bedienungsanleitung

Extech Instruments

Extech Instruments LT510 Bedienungsanleitung

Extech Instruments

Extech Instruments 451181 Bedienungsanleitung

Extech Instruments

Extech Instruments 250W Series Bedienungsanleitung

Extech Instruments

Extech Instruments 407113 Bedienungsanleitung

Extech Instruments

Extech Instruments EX650 Bedienungsanleitung

Extech Instruments

Extech Instruments RH401 Bedienungsanleitung

Extech Instruments

Extech Instruments 480846 Bedienungsanleitung

Extech Instruments

Extech Instruments ExStik PH100 Bedienungsanleitung

Extech Instruments

Extech Instruments TG20 Bedienungsanleitung

Extech Instruments

Extech Instruments 407738 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung