Extech Instruments 380941 Bedienungsanleitung

User Guide

AC/DC Mini Clamp Meter

Model 380941

380941A-EU-EN v1.0 2/14

Introduction

Congratulations on your purchase of Extech’s DC/AC Clamp Meter. This professional meter, with

proper care, will provide years of safe reliable service.

Front Panel Description

1. Current sense jaw

2. Measurement Trigger

3. Function switch

4. Data Hold key

5. Max Min key

6. One-touch DCA zero key

7. LCD Display

8. 40 segment bargraph display

9. Positive input terminal for V, HZ and 

10. COM termin

International Symbols

!Caution ! Refer to the explanation in this Manual

Caution ! Risk of electric shock

Earth (Ground)

Safety

This meter has been designed to be safe in use, but the operator must use caution in its operation.

The rules listed below should be carefully followed for safe operation.

1. NEVER apply voltage or current to the meter that exceeds the specified maximum:

2. USE EXTREME CAUTION when working with high voltages.

3. DO NOT measure voltage if the voltage on the "COM" input jack exceeds 500V above earth

ground.

4. NEVER connect the meter leads across a voltage source while the function switch is in the

current, resistance or diode mode; doing so can damage the meter.

5. ALWAYS discharge filter capacitors in power supplies and disconnect the power when making

resistance or diode tests.

6. ALWAYS turn off the power and disconnect the test leads before opening the back to replace

the fuse or batteries.

7. NEVER operate the meter unless the back cover and the battery/fuse door are in place and

fastened securely.

380941A-EU-EN v1.0 2/14

Operation

AC Current Measurements

WARNING: To avoid electric shock, disconnect the test leads from the meter before making current

measurements.

1) Set the Function switch to the 40 or 200A AC range.

2) Press the jaw trigger and clamp around, fully enclosing a single conductor. Do not allow a gap

between the two halves of the jaw.

3) Read the ACA value on the LCD.

DC Current Measurements

WARNING: To avoid electric shock, disconnect the test leads from the meter before making current

measurements.

1) Set the Function switch to the 40 or 200A DC range.

2) Press the DCA zero key to null the meter display.

3) Press the Trigger to open the current sense Jaw.

4) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of

the jaw.

5) Read the DCA value on the LCD.

AC Voltage Measurements

WARNING: To avoid electric shock or damage to the meter, do not make any voltage

measurements that exceed the maximum specified.

1) Set the Function switch to the VAC position.

2) Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the

COM input.

3) With the pointed end of the test leads measure voltage. Remember that voltage

measurements are made in parallel with the device or circuit under test.

4) Read the ACV value on the LCD.

DC Voltage Measurements

WARNING: To avoid electric shock or damage to the meter, do not make any voltage

measurements that exceed the maximum specified.

1) Set the Function switch to the VDC position.

2) Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the

COM input.

3) With the pointed end of the test leads measure voltage. Remember that voltage

measurements are made in parallel with the device or circuit under test.

4) Read the DCV value on the LCD.

380941A-EU-EN v1.0 2/14

Resistance and Continuity Measurements

WARNING: To avoid electric shock or damage to the meter, remove power to the circuit under test and discharge

all capacitors.

1) Set the Function switch to the position.

2) Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the

COM input.

3) With the pointed end of the test leads measure resistance. Remember that resistance

measurements are made in parallel with the device or circuit under test.

4) Read the resistance value on the LCD.

5) If the resistance is less than 40, the continuity beeper will sound.

Frequency Measurements

1) Ensure that at least 0.1A AC is detectable with an ACA measurement before measuring

Frequency.

2) Set the Function switch to the Hz position.

3) Insert the test leads to the meter as follows: Red lead to “V,Hz,” terminal; Black lead to the

COM input.

4) With the pointed end of the test leads measure frequency

5) Read the Frequency measurement on the LCD in Hz.

Additional Features

Relative Measurements

1) Press the Zero key and the present measurement will Zero.

2) All subsequent measurements are displayed with respect to the zeroed reading. For example,

if a 20A reading is zeroed and a 30A reading is subsequently measured, the LCD will display

10A.

3) To return to normal operation, press the zero key one more time.

4) Note that Relative mode is not available if the MIN/MAX mode is enabled.

5) Relative mode is not available in continuity or Hz mode.

6) Note that the Zero button is disabled if ohm and continuity or Hz functions are selected.

7) LCD displays relative numerical value without bargraph.

Data Hold

To freeze a reading on the LCD, press the Data Hold key. The HOLD icon will appear and the

measurement will be held on the meter’s LCD. To release the Data Hold function and return the

meter to normal operation, press the Data Hold key again. Data Hold is disabled if ohm and

continuity function are selected.

MIN/MAX Reading Mode

Pressing the MIN/MAX key allows the meter to display ONLY the highest and the lowest readings

encountered. Press the MIN/MAX key once to view the minimum reading, press it again to view

the maximum reading. The LCD will toggle between the MIN and MAX values. Press and hold

MIN/MAX button for more than 2 seconds to return to normal operating mode. Zero function will

be disabled when MIN/MAX is enabled. MIN/MAX is not available in continuity or Hz mode.

380941A-EU-EN v1.0 2/14

Specifications

General Specifications

Display 3-3/4 (4032 count) Digit LCD with 40 segment bargraph

Functions ACA, DCA, ACV, DCV, Resistance, Frequency, Continuity

Polarity “-“ indicates negative polarity

Current sensor Hall effect sensor type

Overload indication OL

DCA zero adjust One touch zero key

Display rate 3 readings/second (30 readings/second for bargraph)

Battery Two 1.5V AA batteries

Operating temperature -10oC to 50oC (4oF to 122oF)

Operating humidity < 85% RH

Power consumption Approximately 17mA DC

Sampling time 3 times/sec (display); 30 times/sec (bargraph)

Weight 225g (8 oz.) including battery

Dimensions 183 x 63.6 x 35.6mm (7.2 x 2.5 x 1.4”) (HWD)

Jaw opening 23mm (0.9”)

Standards IEC 1010 Category III 300V, Category II 600V

Range Specifications

Function Range Resolution. Accuracy Overload

protect

DC Current 40A 10mA ±(1.0% +2dgts) 400A DC

0 to 150A 100mA ±(1.0% +2dgts) 400A DC

150 to 200A 100mA ±(2.2% +2dgts) 400A DC

AC Current 50/60Hz 40 to 400Hz

40A 10mA ±(1.0% +3dgts) ±(1.5% +4dgts) 400A AC

0 to 150A 100mA ±(1.0% +3dgts) ±(1.5% +4dgts) 400A AC

150 to 200A 100mA ±(2.2% +3dgts) ±(2.5% ±4dgts) 400A AC

DC Voltage 400V 0.1V ±(1.0% +2dgts) 1000VDC

AC Voltage 50/60Hz 40 to 400Hz

400V 0.1V ±(1.5% +2dgts) ±(2.0% +4dgts) 800V AC

Resistance 40 to 4000.1±(1.0% +2dgts) Beeper <approx

38

600V AC

Frequency 1 to 100k 0.001-100 ±0.5% ±2dgts Sensitivity;

5VAC

600V AC

380941A-EU-EN v1.0 2/14

Maintenance

Battery Replacement

1) When the low battery symbol appears on the LCD the batteries must be replaced.

2) Turn the meter off and remove the rear battery compartment screw.

3) Remove the battery compartment cover and replace the two 1.5V AA cells.

4) Replace the compartment cover and secure the screw.

You, as the end user, are legally bound (Battery ordinance) to return all used

batteries and accumulators; disposal in the household garbage is prohibited!

You can hand over your used batteries / accumulators at collection points in your

community or wherever batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the end of its

lifecycle

Cleaning

Caution: Use only a dry cloth to clean the plastic case.



Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

www.extech.com

Inhaltsverzeichnis

Andere Extech Instruments Messgerät Handbücher

Extech Instruments

Extech Instruments 380460 Bedienungsanleitung

Extech Instruments

Extech Instruments DO700 Bedienungsanleitung

Extech Instruments

Extech Instruments CO250 Bedienungsanleitung

Extech Instruments

Extech Instruments 461920 Bedienungsanleitung

Extech Instruments

Extech Instruments CO200 Bedienungsanleitung

Extech Instruments

Extech Instruments 401025 Bedienungsanleitung

Extech Instruments

Extech Instruments 380652 Bedienungsanleitung

Extech Instruments

Extech Instruments SL400 Bedienungsanleitung

Extech Instruments

Extech Instruments 461700 Bedienungsanleitung

Extech Instruments

Extech Instruments 461995 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL710 Bedienungsanleitung

Extech Instruments

Extech Instruments 461920 Bedienungsanleitung

Extech Instruments

Extech Instruments FM200 Bedienungsanleitung

Extech Instruments

Extech Instruments MA260 Bedienungsanleitung

Extech Instruments

Extech Instruments 433201A Bedienungsanleitung

Extech Instruments

Extech Instruments VT30-E Bedienungsanleitung

Extech Instruments

Extech Instruments PM200 Bedienungsanleitung

Extech Instruments

Extech Instruments CG304 Bedienungsanleitung

Extech Instruments

Extech Instruments HT30 Bedienungsanleitung

Extech Instruments

Extech Instruments AN300 Bedienungsanleitung

Extech Instruments

Extech Instruments CT-3060 Bedienungsanleitung

Extech Instruments

Extech Instruments AN320 Bedienungsanleitung

Extech Instruments

Extech Instruments PH220A Bedienungsanleitung

Extech Instruments

Extech Instruments EX845 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung