Extech Instruments PH220A Bedienungsanleitung

User Guide

Waterproof Palm pH Meter

Model PH220A

Introduction

Congratulations on your purchase of the Extech PH220 waterproof pH/mV meter. This

microprocessor-based device with tactile push-buttons is battery operated and ideal for

field use. The PH220 simultaneously displays pH and temperature. The rubber holster

which protects the meter has a magnetic backing for convenient mounting. The built-in

memory (25 readings) allows STORE, RECALL, and CLEAR functionality. Careful use of

this meter will provide years of reliable service.

7.00

Model PH220 Version 3.1 11/20052

Specifications

Range (Resolution) Accuracy

mV (ORP) ± 1999 mV DC (1 mV) ± 2mV

Temperature 32 to 212oF (<100o;1o >100o)

0 to 100oC (0.1°<100°;1°>100°)

± 1.0oF

± 0.5oC

0.00 to 14.00pH (0.01pH) ± 0.02pH

Note 1: Accuracy does not include pH buffer

temperature coefficient

Note 2: Accuracy specified from 0.02pH to 13.98pH

Temperature Compensation 32 to 212oF (0-100oC) Automatic ‘ATC’

Power 9 volt alkaline battery

Display Dual LCD display for simultaneous pH and temperature

readings

Over-range or open indication Displays "HHH" for over-range or open input conditions

Displays “LLL” for under-range

pH Calibration points 4.00, 7.00, 10.00 (1, 2, or 3 point calibration can be

performed)

Auto Power OFF 10 minutes from last key-press (can be disabled)

Low Battery Indication Fill bars in the battery display icon represent

battery power status. The fewer the bars, the weaker

the battery power.

Dimensions / Weight 4.25 x 3.00 x 1.18" (108 x 75 x 30mm) / 4.8 oz. (135g)

Accessories supplied with kit Battery, suction cup holder, clip holder, stick electrode

for model PH220-S, standard electrode with 39” cable

for model PH220-C.

Model PH220 Version 3.1 11/20053

Meter Description

1. Battery Compartment (under holster)

2. Rubber Holster

3. LCD Display

4. Function buttons

5. Electrode input

Basic Display Description

1. Measurement value

2. Battery status

3. Units of measure

4. Temperature units

5. Solution temperature

Note that there are other more specialized displays that appear on the LCD that have not

been included in this basic operation display description. Other display icons are used and

are discussed in the appropriate sections of this manual.

Order of Operations

1. Calibrate the instrument as described later in this manual.

2. Determine the test type (pH or ORP) and carefully follow the directions for the desired

test.

3. Configure the meter to display in the desired units of measure for temperature (oC or

oF). This is included as a step in the pH measurement instructions.

4. Pay close attention to detail, step by step instructions, and electrode cleaning/rinsing

recommendations. Slight deviations in test procedures and test habits can have a

significant effect on test results.

7.00

Model PH220 Version 3.1 11/20054

Calibration (pH only)

The sensitivity of a pH electrode degrades over time, it is very important to frequently

calibrate the meter to the electrode. pH electrodes can be thought of as batteries in that

they run down with time and use.

Calibration is performed using standard buffer solutions at room temperature (78°F, 25°C).

Buffer solutions are solutions of a known pH that have the useful property of resisting

changes in pH. These can be purchased already mixed or in capsule form and are usually

available in three pH values, pH 4.00, pH 7.00 and pH 10.00.

Calibration is always performed using the pH 7.00 buffer first, followed by a second

calibration. Select pH 4 buffer for the second calibration if typical measurements will be

less than pH7 or use a pH 10 buffer if typical measurements will be greater than ph 7.

In order to obtain the most accurate results possible, a pH meter should be

calibrated at least once each day. Note that the mV (ORP) function does not require

calibration.

pH Calibration Procedure

1. Place the electrode into a 7.00 pH buffer solution. Press and hold the CAL button until

“CAL” appears in the display.

2. The instrument automatically recognizes the solution and calibrates to that value.

Note that if the solution is off by more than 1 pH unit from the 4, 7, or 10 pH buffer, or

if the electrode slope is low, the instrument will assume an error and abort the

calibration (End will be displayed, and the unit will return to the normal measurement

mode.)

3. During calibration, the pH reading flashes on the main display.

4. When calibration is complete, the instrument automatically displays ‘SA’ followed by

‘End’ and then returns to the normal operation mode.

5. For a two or three point calibration, repeat steps 1-4. When doing a 2 or 3 point

calibration, calibrate with pH 7 buffer first, then follow with pH 4 and/or pH 10.

CAL Reminder Display

When in pH measurement mode, the CAL icon will appear if a calibration has not been

performed after 15 on/off cycles of the instrument. The CAL display is simply a reminder

and will turn off when the pH electrode is recalibrated. The reminder does not affect

function in any way.

Model PH220 Version 3.1 11/20055

Measuring pH

Electrodes should always be rinsed before and between samples

with distilled or DI (de-ionized) water to remove all traces of

storage solution, process media, or previous test solution.

1. Connect the pH electrode to the meter.

2. Turn the meter on using the on/off button . Wait for the self test (‘SLF tSt’) to

finish.

3. Use the MODE button to select pH mode. The unit of measure appears on the LCD.

4. To change the unit of measure for temperature (oC to oF or oF to oC), press and hold

the MODE button for 3 seconds. The LCD reflects the current unit of measure.

5. Rinse the electrode with distilled or deionized water.

6. Place the electrode in the solution. Allow 30 seconds for the electrode/ATC to reach

thermal equilibrium with the buffer solution.

7. After the measurement stabilizes, view the pH reading on the main display. An out of

range reading is indicated by the display icon ‘HHH’. Note that ‘HHH’ will also display

when the electrode is disconnected from the meter.

8. When the test is complete rinse the electrode with distilled or deionized water.

Measuring ORP (millivolts mV)

1. Connect the ORP electrode to the meter.

2. Rinse the ORP electrode

3. Turn the meter on using the on/off button . Wait for the self test (‘SLF tSt’) to finish.

4. Use the MODE button to select mV mode. The display will reflect the unit of measure.

5. Place the electrode into a sample solution. When the LCD stabilizes it will read the

redox potential of the sample in millivolts (mV).

6. When the test is complete rinse the electrode with distilled or deionized water.

Automatic Temperature Compensation (ATC)

The millivolt output of a pH electrode varies with temperature, and for this reason the meter

must compensate for these variations to obtain accurate measurements. The PH220

automatically compensates for solution temperature changes with the electrode’s built-in

thermometer. The temperature compensation is active when the solution temperature

deviates from room temperature. The temperature of a solution is displayed on the lower

LCD line of the instrument.

Automatic Power OFF

To conserve battery power, the instrument automatically shuts off after 10 minutes of

inactivity. To disable or enable this feature, follow the steps below:

•To disable: With the power on, press and hold the on/off button for 2 seconds

(oFF and AtP will display). The Auto Power OFF feature is now disabled.

•To enable: With the power on, press and hold the on/off button for 2 seconds (on

and AtP will display). The Auto Power OFF feature is now enabled.

•Each time the meter is turned off the Auto power OFF feature is set to the enabled

mode.

Model PH220 Version 3.1 11/20056

Storing and Recalling Readings

This instrument has the ability to store up to 25 measurement readings. At a later time the

readings can be recalled and viewed. Readings are saved even after the instrument has

been turned off.

STORE Readings

The steps below cover the STORE process in detail:

1. Take a measurement as described earlier in this manual.

2. Momentarily press the STORE/RECALL button to save the reading. The reading will

be held on the display (the HOLD and STORE icons will appear). In addition, the

storage location (1 to 25) will briefly appear on the lower portion of the LCD.

3. Note: The temperature reading associated with the pH reading is also saved.

4. Press the STORE/RECALL button again to release the ‘hold’ feature. The instrument

will then return to normal operation.

5. Note that when all 25 storage locations are filled the instrument begins writing over

the previously stored data.

RECALL Readings

The steps below cover the RECALL process in detail:

1. Press and hold the STORE/RECALL button until a number appears on the main

display. This number is the storage location for the most recent reading.

2. The number will switch off after 1 second and the stored reading will appear. The

RECALL icon will appear and remain on the entire time the recall mode is accessed.

3. While in the RECALL mode, use the STORE/RECALL button to scroll through the

stored readings. The most recent readings will show first (LAST IN – FIRST OUT).

4. Press and hold the STORE/RECALL button until the END display appears. Release

the button and the instrument will return to normal operation mode.

5. Note that if there are no readings in memory, the display will show END when the

user attempts to access the RECALL mode.

ERASE Readings

The steps below cover the ERASE (CLEAR) process in detail:

1. Press and hold STORE/RECALL and the CAL buttons simultaneously for 4 seconds.

2. The ‘CLr’ display will appear indicating that all readings have been erased.

3. Release the buttons to return to normal operation mode.

Temperature Offset Adjustment

Applications may arise where it is desirable to offset the instrument’s temperature display.

This instrument allows a temperature display offset adjustment of ±9oF (±5oC). To do so,

follow the steps below:

1. Press and hold the CAL, MODE, and STORE/RECALL buttons simultaneously for 6

seconds.

2. The main display will indicate the current offset. The lower display will show ‘t_O’.

3. Use the CAL button to decrease the offset value and the MODE button to increase it.

4. Press and hold the STORE/RECALL button for 2 seconds to exit this mode. The

instrument will display ‘SA’ (save) and ‘END’ before returning to the normal operation

mode.

5. The temperature display will now indicate the actual temperature ± the offset value.

Model PH220 Version 3.1 11/20057

Battery Replacement

The 9 volt alkaline battery that powers the instrument requires replacing when all battery

icon ‘fill bars’ are depleted. To replace the battery follow the steps below:

1. Disconnect the electrode from the instrument.

2. Remove the instrument’s protective jacket by pulling it over the top of the meter

(ensure that the electrode is disconnected).

3. Pry the battery compartment up from the top of the meter using a screwdriver or

coin at one of the two indentations (see diagram).

4. Replace the 9V battery.

5. Insert the battery compartment into the instrument until the compartment is flush

with the top of the instrument. The compartment can only be fully inserted in one

direction and the battery compartment is labeled as to the polarity orientation of the

battery.

6. Replace the protective holster.

Model PH220 Version 3.1 11/20058

Electrode Maintenance and Troubleshooting

Most pH measurement difficulties are caused by the electrode. Careful handling and proper

storage of the electrode will increase measurement accuracy and electrode life.

Electrodes should be rinsed to remove all traces of storage solution, process medium, or

previous test solution.

Electrode Storage

The electrode should be stored in a soaker bottle or wetting cap filled with pH4 buffer.

Never store an electrode in distilled or deionized water as this will cause migration of the fill

solution from the electrode.

Electrode Cleaning

The type of electrode coating that occurs over time will determine the cleaning method.

Soft coatings can be removed by vigorous stirring or by using a squirt bottle. Organic

chemical coating (hard coatings) should be chemically removed. Only in extreme cases

should the bulb be cleaned mechanically.

Troubleshooting an Electrode

Symptom Cause Recommendation

Clogged Junction Soak in 4.07 M Potassium Chloride (KCl)

@ 60oC for 30 minutes.

Strong Alkaline measurement Soak in 0.1 M HCL overnight.

Deteriorated Gel layer Replace electrode.

Protein coating on electrode

surface Soak in 1 gm Pepsin dissolved in 100ml of

0.1 m HCL for 30 minutes or as needed.

Oil, paint, dyes, suspended

solids etc. are on sensor Rinse electrode alternately with a materials

solvent and a buffer 7.00.

Organic solvents are coating

the sensor Organic mole fraction has to be less than

50% to assure reasonable readings. Limit

time of measurement. Keep probe in the

7.0 buffer between readings.

Long response time or

reading drift

Dehydrated membrane Read solution for dry bulb below:

Dry Bulb Long term storage without

wetting Soak electrode tip in wetting cap filled with

1ml 7.00 buffer for 24 to 48 hours

Static Charge Wiping electrodes Rinse electrode in 7.0 buffer and blot. Do

no wipe electrode.

Same readings in different

buffers and samples Cracked or broken bulb Replace electrode. Use bulb guard. Avoid

plunging electrode to bottom of container

and spinning bars. Wetting cap will protect

bulb between tests.

Erratic LCD display Samples have low ionic

strength (lacks salt); e.g.

distilled, de-ionized, boiled,

lake water (high pressure)

For each 50 ml of sample add 1 drop

(50uL) of SAT. KCl (No alteration in pH will

occur using inert KCl).

Model PH220 Version 3.1 11/20059



Support line (781) 890-7440

Technical support: Extension 200; E-mail: [email protected]m

Repair & Returns: Extension 210; E-mail: [email protected]

Product specifications subject to change without notice

For the latest version of this User’s Guide, Software updates, and other

up-to-the-minute product information, visit our website: www.extech.com

Extech Instruments Corporation, 285 Bear Hill Rd., Waltham, MA 02451

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also

provides NIST certification for most products. Call the Customer Service Department for

information on calibration services available for this product. Extech recommends that

annual calibrations be performed to verify meter performance and accuracy.

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and

workmanship for one year from date of shipment (a six month limited warranty applies to sensors andcables).

If it should become necessary to return the instrument for service during or beyond the warranty period,

contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our website

www.extech.com for contact information. A Return Authorization (RA) number must be issued before any

product is returned to Extech. The sender is responsible for shipping charges, freight, insurance and proper

packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the

user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair, or

unauthorized modification. Extech specifically disclaims any implied warranties or merchantability or fitness for

a specific purpose and will not be liable for any direct, indirect, incidental or consequential damages. Extech's

total liability is limited to repair or replacement of the product. The warranty set forth above is inclusive and no

other warranty, whether written or oral, is expressed or implied.

Inhaltsverzeichnis

Andere Extech Instruments Messgerät Handbücher

Extech Instruments

Extech Instruments RH520 Bedienungsanleitung

Extech Instruments

Extech Instruments 461995 Bedienungsanleitung

Extech Instruments

Extech Instruments AN200 Bedienungsanleitung

Extech Instruments

Extech Instruments MO210 Bedienungsanleitung

Extech Instruments

Extech Instruments MA440 Bedienungsanleitung

Extech Instruments

Extech Instruments 407777 Bedienungsanleitung

Extech Instruments

Extech Instruments MO57 Bedienungsanleitung

Extech Instruments

Extech Instruments 45118 Bedienungsanleitung

Extech Instruments

Extech Instruments RH300 Bedienungsanleitung

Extech Instruments

Extech Instruments 451181 Bedienungsanleitung

Extech Instruments

Extech Instruments 461830 Bedienungsanleitung

Extech Instruments

Extech Instruments EC150 Bedienungsanleitung

Extech Instruments

Extech Instruments HDV-WTX2 Abmessungen

Extech Instruments

Extech Instruments 407790 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL300 Bedienungsanleitung

Extech Instruments

Extech Instruments RF153 Bedienungsanleitung

Extech Instruments

Extech Instruments MO257 Bedienungsanleitung

Extech Instruments

Extech Instruments SDL310 Bedienungsanleitung

Extech Instruments

Extech Instruments 401027 Bedienungsanleitung

Extech Instruments

Extech Instruments LT510 Bedienungsanleitung

Extech Instruments

Extech Instruments 380803 Bedienungsanleitung

Extech Instruments

Extech Instruments 382090 Bedienungsanleitung

Extech Instruments

Extech Instruments HD300 Bedienungsanleitung

Extech Instruments

Extech Instruments SL130 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung