Extreme Networks 10965 Bedienungsanleitung

Extreme Networks

LRM/MACsec Adapter

Quick Reference

Part no. 10965

Hardware Components

Figure 1 shows the ports, LEDs, and connections on the LRM/MACsec

Adapter.

Figure 1 LRM/MACsec Adapter Converter: Front Panel

Installation Site Requirements

The installation site must meet the following requirements:

• Located within 50 cm (19.7 in) of the host switch to which it will be

attached

• A temperature between 0°C (32°F) and 45°C (113°F), with

fluctuations of less than 10°C (18°F) per hour

Handling the Equipment

To minimize the risk of ESD damage, follow appropriate ESD

procedures when unpacking and handling the LRM/MACsec Adapter.

These include unpacking the equipment in an ESD safe environment

and wearing appropriate ESD protective gear, such as ESD-safe

footwear and ESD wrist straps where appropriate.

Unpack the equipment as follows:

1 Remove the packing material protecting the equipment.

2 Remove the tape seal on the non-conductive bag to remove the

equipment.

3 Perform a visual inspection of the equipment for any signs of

physical damage. Contact Extreme Networks if there are any signs

of damage. See “Getting Help” for more information on contacting

Extreme Networks.

Installing the LRM/MACsec Adapter

You can install the LRM/MACsec Adapter converter in a standard

equipment rack, in any of three ways shown in Figure 2.

Figure 2 Mounting Options for the LRM/MACsec Adapter

Mounting Option 1: Horizontal

To mount the LRM/MACsec Adapter vertically on the rack

1 Using two small M4x6.5mm screws (included), attach the bracket to

the holes in one side of the adapter so that the mounting ear

extends away from the adapter.

Figure 3 shows the bracket attached to the adapter.

Figure 3 Bracket Attached to Adapter for Horizontal Mounting

2 Using two rack mounting screws (not included) attach the

mounting ear to the rack.

The adapter ports should face toward the front.

3 Connect the adapter to the switch, following the instructions in

“Connecting the LRM/MACsec Adapter to the Host Switch”.

Mounting Option 2: In the 5-Slot Bracket

To mount the LRM/MACsec Adapter in the 5-slot bracket:

1 Using standard rack mounting screws (not included), secure the

bracket to the rack.

2 Set the adapter in one of the bracket slots.

3 Secure the adapter to the bracket using one of the M4x6.5mm

screws provided with the bracket.

4 Mount up to four additional LRM/MACsec Adapter units on the

bracket, as described in steps 2 and 3.

5 Connect the adapters to the switch, following the instructions in

“Connecting the LRM/MACsec Adapter to the Host Switch”.

Mounting Option 3: Vertical

To mount the LRM/MACsec Adapter vertically on the rack:

1 Using two rack mounting screws (not included), attach the vertical

mounting bracket to the rack so that the mounting ear extends

outward from the front of the rack.

2 Using two small M4x6.5mm screws (included), attach the bracket to

the holes in the bottom of the adapter.

The adapter ports can face upward or downward as needed.

3 Connect the adapter to the switch, following the instructions in

“Connecting the LRM/MACsec Adapter to the Host Switch”.

Connecting the LRM/MACsec Adapter to

the Host Switch

After mounting the LRM/MACsec Adapter in the rack, attach it to the

host switch by doing the following:

1 Insert one of the 50 cm SFP cables, included with the adapter, into

Host Port1 on the front of the LRM/MACsec Adapter.

This SFP cable is provided especially for use with the

LRM/MACsec Adapter. It is not a standard SFP cable.

2 Insert the other end of the cable into an SFP port on the switch.

3 Repeat steps 1 and 2 to connect Host Port2 to the switch. Both

Host Port1 and Host Port2 must be connected to the host switch.

The LRM/MACsec Adapter receives power through its connection to

the host switch’s SFP port. Optionally, in addition to the power it

receives from the switch, it can receive power through the USB

connector on the front panel.

When the LRM/MACsec Adapter is connected to the host switch,

verify that the adapter’s power LED turns on. If the power LED does

not turn on, recheck the connection between the adapter and the

power source(s).

Specifications

LRM/MACsec Adapter

Part number: 10965

Unpackaged Weight: 300 g (0.66 lb)

Dimensions:

3.00 cm (1.18 in) H

7.60 cm (2.99 in) W

12.35 cm (4.86 in) L

Operating Temperature:

0°C to 40°C (32°F to 104°F) when used with Tunable DWDM SFP+,

ER SFP+, ZR SFP+, and Bidirectional 120 km SFP optics modules

0°C to 45°C (32°F to 113°F) when used with all other optics modules

Storage Temperature: -40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity: 10% to 95% (non-condensing)

Five-Slot Bracket

Part number: 10966

Unpackaged Weight: 487 g (1.07 lb)

Dimensions:

4.32 cm (1.70 in) H

5.60 cm (2.20 in) L

48.26 cm (19.00 in) W

Electrical Hazard: Only qualified personnel should perform installation

procedures.

Risques d’électrocution: Seul un personnel qualifié doit effectuer les

procédures d'installation.

1USB connector 3SFP+ ports (host)

2SFP+ ports (link)

Caution: Failure to follow proper ESD handling procedures may result in

damage to the equipment.

1Horizontal Mount 3Vertical Mount

25-Slot Bracket (part no. 10966)

Getting Help

For additional support related to your equipment or this document,

contact Extreme Networks using one of the following methods:

Legal Notices

Extreme Networks, Inc. reserves the right to make changes in specifications and

other information contained in this document and its website without prior

notice. The reader should in all cases consult representatives of Extreme

Networks to determine whether any such changes have been made.

The hardware, firmware, software or any specifications described or referred to

in this document are subject to change without notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks or registered

trademarks of Extreme Networks, Inc. in the United States and/or other

countries.

All other names (including any product names) mentioned in this document are

the property of their respective owners and may be trademarks or registered

trademarks of their respective companies/owners.

For additional information on Extreme Networks trademarks, please see:

www.extremenetworks.com/company/legal/trademarks/

Warranty

Warranty information for LRM/MACsec Adapter equipment is located online at:

www.extremenetworks.com/go/warranty

Part no. 121211-00

Regulatory and Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment uses, generates, and can radiate radio

frequency energy and if not installed in accordance with the operator’s

manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause

interference in which case the user will be required to correct the

interference at his own expense.

WARNING: Changes or modifications made to this device which are not

expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Industry Canada Notice

CAN ICES-3 (A)/NMB-3(A)

This digital apparatus does not exceed the class A limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la class A

prescrites dans le Règlement sur le brouillage radioélectrique édicté par le

ministère des Communications du Canada.

Product Safety

This product complies with the following international safety standards:

• UL 62368-1:2014

• UL 60950-1 2nd edition, A2:2014

• CAN/CSA-C22.2 No.62368-1-14:2014

• IEC 62368-1:2014

• EN 62368-1:2014

• IEC 60950-1:2005 2nd+A1:2009+A2:2013

• EN 60950-1:2006+A11+A1+A12+A2

• 2014/35/EU

Korea EMC Statement (KCC)

Electromagnetic Compatibility (EMC)

This product complies with the following: FCC 47 CFR Part 15 Subpart B

Class A (US), ICES-003 (Canada), EN 55032 (ITE Emissions), EN 55024

(ITE Immunity), EN 61000-3-2 (Harmonics), EN 61000-3-3 (Flicker),

2014/30/EU (EMC Directive).

VCCI Notice

This is a Class A product based on the standard of the Voluntary Control

Council for Interference by Information Technology Equipment (VCCI). If

this equipment is used in a domestic environment, radio disturbance may

arise. When such trouble occurs, the user may be required to take

corrective actions.

Hazardous Substances- China and Taiwan BSMI RoHS

Guidance concerning the China and Taiwan BSMI RoHS (Restriction of

Hazardous Substances) directive for this Extreme Networks® product can

be found on the following web page:

www.extremenetworks.com/support/documentation/restriction-

hazardous-substances/

The page contains tables detailing the presence of 10 substances defined

by the RoHS directive.

Hazardous Substances

This product complies with the requirements of Directive 2011/65/EU of

the European Parliament and of the Council of 8 June 2011 on the

restriction of the use of certain hazardous substances in electrical and

electronic equipment.

European Waste Electrical and Electronic Equipment (WEEE) Notice

In accordance with Directive 2012/19/EU of the European Parliament on

waste electrical and electronic equipment (WEEE):

1The symbol above indicates that separate collection of electrical and

electronic equipment is required.

2When this product has reached the end of its serviceable life, it cannot

be disposed of as unsorted municipal waste. It must be collected and

treated separately.

3It has been determined by the European Parliament that there are

potential negative effects on the environment and human health as a

result of the presence of hazardous substances in electrical and

electronic equipment.

4It is the users’ responsibility to utilize the available collection system to

ensure WEEE is properly treated.

For information about the available collection system, please contact

Extreme Customer Support at +353 61 705500 (Ireland).

Product

Documentation

https://www.extremenetworks.com/documentation/

Global Technical

Assistance Center

(GTAC)

Phone: 1-800-998-2408 (toll-free in U.S. and Canada)

or +1-408-579-2826. For the support phone number in

your country, visit:

http://www.extremenetworks.com/support/contact/

GTAC Knowledge Get on-demand and tested resolutions from the GTAC

Knowledgebase, or create a help case if you need more

guidance.

Visit: https://gtacknowledge.extremenetworks.com/

The Hub A forum for Extreme customers to connect with one

another, get questions answered, share ideas and

feedback, and get problems solved. The community is

monitored by Extreme Networks employees, but is not

intended to replace specific guidance from GTAC.

Visit: https://community.extremenetworks.com

Support Portal Manage cases, downloads, service contracts, product

licensing, and training and certifications.

Visit: http://support.extremenetworks.com/

Warning: The LRM/MACsec Adapter converter is designed for installation in

restricted access locations.

Avertissement: Le convertisseur est conçus pour une installation dans des

endroits à accès restreint.

Andere Extreme Networks Adapter Handbücher

Extreme Networks

Extreme Networks SA201 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung