Extreme Networks Altitude 4511 Bedienungsanleitung

Extreme Networks, Inc.

3585 Monroe Street

Santa Clara, California 95051

(888) 257-3000

(408) 579-2800

http://www.extremenetworks.com

Altitude™ 4511 Access Point

Installation Guide

Published: October 2012

Part number: 120676-00 Rev 03

Altitude™ 4511 Access Point Installation Guide

AccessAdapt, Alpine, Altitude, BlackDiamond, EPICenter, ExtremeWorks Essentials, Ethernet

Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby

Router Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go

Purple Extreme Solution, ExtremeXOS ScreenPlay, ReachNXT, Sentriant, ServiceWatch, Summit,

SummitStack, Triumph, Unified Access Architecture, Unified Access RF Manager, UniStack, the

Extreme Networks logo, the Alpine logo, the BlackDiamond logo, the Extreme Turbodrive logo, the

Summit logos, and the Powered by ExtremeXOS logo are trademarks or registered trademarks of

Extreme Networks, Inc. or its subsidiaries in the United States and/or other countries.

sFlow is a registered trademark of InMon Corporation.

Specifications are subject to change without notice.

All other registered trademarks, trademarks, and service marks are property of their respective

owners.

Altitude™ 4511 Access Point Installation Guide

Table of Contents

Chapter 1: Introduction....................................................................................................5

Document Conventions............................................................................................................... 6

Warnings..................................................................................................................................... 6

Site Preparation .......................................................................................................................... 7

Package Contents ...................................................................................................................... 7

Features...................................................................................................................................... 7

Chapter 2: Hardware Installation ....................................................................................9

Installation Instructions ............................................................................................................... 9

Precautions............................................................................................................................... 10

Access Point Placement ........................................................................................................... 10

Wall Mount Installation.............................................................................................................. 10

Telco Box Installation................................................................................................................ 14

Altitude 4511 Access Point Antennas....................................................................................... 18

LED Indicators .......................................................................................................................... 18

Chapter 3: Defining a Basic Configuration ..................................................................19

Using the Initial Setup Wizard................................................................................................... 19

Chapter 4: Specifications ..............................................................................................41

Electrical Characteristics........................................................................................................... 41

Physical Characteristics............................................................................................................ 41

Radio Characteristics................................................................................................................ 42

Chapter 5: Regulatory Information ...............................................................................43

Regulatory Overview................................................................................................................. 43

Wireless Device Country Approvals.......................................................................................... 43

Country Selection – Note for AP & Wireless Controller ..................................................... 44

Frequency of Operation – FCC and IC.............................................................................. 44

Health and Safety Recommendations ...................................................................................... 45

Warnings for the use of Wireless Devices......................................................................... 45

Potentially Hazardous Atmospheres – Fixed Installations................................................. 45

Safety in Hospitals.............................................................................................................45

RF Exposure Guidelines........................................................................................................... 46

Table of Contents

Altitude™ 4511 Access Point Installation Guide

Safety Information ............................................................................................................. 46

International .............................................................................................................................. 46

EU............................................................................................................................................. 46

US and Canada ........................................................................................................................ 46

Power Supply............................................................................................................................ 47

Radio Frequency Interference Requirements – FCC................................................................ 47

Radio Frequency Interference Requirements – Canada ......................................................... 48

Radio Transmitters ............................................................................................................ 48

CE Marking and European Economic Area (EEA).................................................................... 48

Statement of Compliance.......................................................................................................... 49

Waste Electrical and Electronic Equipment (WEEE) ................................................................ 50

TURKISH WEEE Statement of Compliance ............................................................................. 52

Japan (VCCI) - Voluntary Control Council for Interference Class B ITE .................................. 52

Korea Warning Statement for Class B ITE ............................................................................... 52

Other Countries ........................................................................................................................ 53

Australia............................................................................................................................. 53

Brazil.................................................................................................................................. 53

Chile .................................................................................................................................. 53

Mexico ............................................................................................................................... 54

Taiwan ............................................................................................................................... 54

Korea ................................................................................................................................. 55

Chapter 6: Customer Support .......................................................................................57

Registration............................................................................................................................... 57

Documentation.......................................................................................................................... 58

Altitude™ 4511 Access Point Installation Guide

CHAPTER

Introduction

The Altitude™ 4511 Access Point links wireless 802.11a/b/g/n devices to the controller,

enabling the growth of your wireless network with a cost-effective alternative to standard

Access Points.

The Altitude 4511 Access Point is an enterprise class 802.11n Access Point, installed in

minutes anywhere a CAT-5 (or better) cable is located. The Altitude 4511 Access Point’s

mechanical design is optimized for installation over a standard CAT-5 (or better) wall jack.

The AP does not protrude into the wall cavity, allowing for an efficient heat transfer and a

universal installation over a standard Telco wiring plate. The Altitude 4511 Access Point’s

modular design allows the end-user to add switched Ethernet ports as-needed, and attach a

standard keystone or Leviton QuickPort

modular connector to the wall plate.

The Altitude 4511 Access Point ships with a single dual-band radio supporting the 802.11a/

b/g/n radio bands.

The Altitude 4511 Access Point receives all power and transfers data through the same CAT-

5 or better Ethernet cable. There is no additional power supply required. An 802.113af

Ethernet switch or an Extreme Networks Summit

WM3400 or Summit WM3600 model

controller (both PoE capable) is required to power the Altitude 4511 Access Point.

Once cabled and powered, the Altitude 4511 Access Point can be set to function as either a

Virtual Controller AP, Standalone AP or Dependent Mode AP. If set to function as a

Standalone AP, the Access Point defines its own management configuration. If set to

function as a Dependent Mode Access Point, the Altitude 4511 Access Point receives its

configuration from its connected Summit WM3400, WM3600 or WM3700 controller or

another Altitude 4511 Access Point in Virtual Controller AP Mode.

The Altitude 4511 Access Point can be ordered for US deployment (Part Number 15761),

ordered for deployment in the European Union regulatory doman (Part Number 15782), or

the rest of the world (Part Number 15762).

Chapter 1: Introduction

Altitude™ 4511 Access Point Installation Guide

Document Conventions

The following graphical alerts are used in this document to indicate notable situations

NOTE

Tips, hints, or special requirements that you should take note of.

CAUTION

Care is required. Disregarding a caution can result in data loss or equipment malfunction.

WARNING!

Indicates a condition or procedure that could result in personal injury or equipment damage.

Warnings

●

Read all installation instructions and site survey reports, and verify correct equipment

installation before connecting the Altitude 4511 Access Point to its power source.

●

Remove jewelry and watches before installing this equipment.

●

Verify that the unit is grounded before connecting it to the power source.

●

Verify any device connected to this unit is properly wired and grounded.

●

Connect all power cords to a properly wired and grounded electrical circuit.

●

Verify the electrical circuits have appropriate overload protection.

●

Attach only approved power cords to the device.

●

Verify the power connector and socket are accessible at all times during the operation of

the equipment.

●

Do not work with power circuits in dimly lit spaces.

●

Do not install this equipment or work with its power circuits during thunderstorms or

other weather conditions that could cause a power surge.

●

Verify there is adequate ventilation around the device, and that ambient temperatures

meet equipment operation specifications.

Site Preparation

Altitude™ 4511 Access Point Installation Guide

Site Preparation

●

Consult your site survey and network analysis reports to determine specific equipment

placement, power drops, and so on.

●

Assign installation responsibility to the appropriate personnel.

●

Identify and document where all installed components are located.

●

Ensure adequate, dust-free ventilation to all installed equipment.

●

Prepare Ethernet and console port connections.

●

Verify cable lengths are within the maximum 100 meter allowable length.

Package Contents

●

Altitude 4511 Access Point with internal (integrated) antennas

●

Mounting plate (used for both wall mount and Telco Box installations)

●

Mounting plate lock screw

●

Altitude 4511 Access Point Installation Guide (This Guide)

●

RJ-45 double plug interconnect cable

●

Fast Ethernet port 1 interconnect cable

Features

●

One RJ-45 PoE Ethernet port (built into the Altitude 4511 Access Point)

●

Optional second RJ-45 Ethernet port utilizing a pass through (keystone) cable (included)

●

Optional three port Ethernet expansion module (sold separately)

●

2 LED indicators

The pass through (keystone) cable provides an option to add a second Ethernet port before

installing the Altitude 4511 Access Point.

The Altitude 4511 Access Point has one RJ-45 connector supporting a 10/100 Ethernet port

and requires 802.3af compliant power from an external source.

Chapter 1: Introduction

Altitude™ 4511 Access Point Installation Guide

The Altitude 4511 Access Point ships with a single dual-band radio supporting the 802.11a/

b/g/n radio bands.

The Access Point contains runtime firmware which enables the unit to boot after either a

power up or a watchdog reset. The runtime firmware on the Access Point can be updated

via the Ethernet interface.

The front of the Altitude 4511 Access Point has an access cover that can be removed to

expose an additional connector. A three port RJ-45 Ethernet expansion module connects to

the hidden header and snaps onto the Altitude 4511 Access Point in place of the access

cover.

Remove the Altitude 4511 Access Point’s access cover by inserting a tool into the circular

hole (opening) on the bottom of the Altitude 4511 Access Point. Pull the access cover up and

away from the Altitude 4511 Access Point. Reverse the procedure to install the expansion

module.

The Ethernet expansion module has three ports labeled FE2, FE3 and FE4.

The expansion module (Part Number KT-6511-0000D-WR) is a separately orderable

component from Extreme Networks.

Altitude™ 4511 Access Point Installation Guide

CHAPTER

Hardware Installation

Installation Instructions

An Altitude 4511 Access Point mounts either on a wall, under a table or over a Telco Box.

The Altitude 4511 Access Point is not plenum rated.

NOTE

The provided metal mounting plate is fastened to an existing standard Telco in-wall box. The

box is customer provided within the customer building structure, and can be either plastic or metal in

composition. Screws and other mounting hardware are not included.

The Altitude 4511 Access Point is mounted to a wall or Telco Box so the mounting plate is

flush with the mounting surface.

The Altitude 4511 Access Point snaps on to the mounting plate without the use of tools or

fastening hardware. Removal of the Altitude 4511 Access Point from the mounting plate can

be accomplished without the use of a tool. A mounting lock screw is provided to help

ensure a tamper resistant installation.

NOTE

Once installed onto the mounting plate, the assembly can resist a minimum of 10 lbs of force

before unit breakage or accidental disassembly.

Chapter 2: Hardware Installation

Altitude™ 4511 Access Point Installation Guide

To prepare for an Altitude 4511 Access Point installation, perform the following:

1Verify the contents of the box includes the intended Altitude 4511 Access Point and

accessory hardware.

2Review site survey and network analysis reports to determine the location and mounting

position for the Altitude 4511 Access Point.

3Connect a CAT-5 or better Ethernet cable to a PoE compatible device and run the cable

to the installation site. Ensure there is sufficient cable slack to perform the installation

steps.

Precautions

Before installing an Altitude 4511 Access Point:

●

Verify the intended Altitude 4511 Access Point deployment location is not prone to

moisture or dust.

●

Verify the environment has a continuous temperature range between 0° C to 40° C.

Access Point Placement

For optimal performance, install the Access Point away from transformers, heavy-duty

motors, fluorescent lights, microwave ovens, refrigerators and other industrial equipment.

Signal loss can occur when metal, concrete, walls or floors block transmission. Install the

Access Point in an open area or add Access Points as needed to improve coverage.

To maximize the Access Point’s radio coverage area, Extreme Networks recommends

conducting a site survey to define and document radio interference obstacles before

installing the Access Point.

Wall Mount Installation

To support wall mount installations, the metal mounting plate (provided with the Altitude

4511 Access Point) is fastened to a flat wall surface. The wall should be of gypsum board,

plaster, wood or concrete in composition.

Andere Handbücher für Altitude 4511

Inhaltsverzeichnis

Andere Extreme Networks Drahtloser Zugangspunkt Handbücher

Extreme Networks

Extreme Networks ExtremeWireless AP3965i Bedienungsanleitung

Extreme Networks

Extreme Networks IdentiFi Wireless WS-AP3825i Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP510i Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP3935e Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless 31012 Bedienungsanleitung

Extreme Networks

Extreme Networks Extreme Wireless WSAP3825i Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP560h Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP560h Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP3000X Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 4600 Series Bedienungsanleitung

Extreme Networks

Extreme Networks WiNG AP-7602 Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeMobility AP410i/e Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP3000X Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP360i ExtremeWireless... Bedienungsanleitung

Extreme Networks

Extreme Networks AP-7562 Bedienungsanleitung

Extreme Networks

Extreme Networks AP510C Installationshandbuch

Extreme Networks

Extreme Networks AP410C Bedienungsanleitung

Extreme Networks

Extreme Networks AP305C Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP5010 Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP3965i Bedienungsanleitung

Extreme Networks

Extreme Networks ExtremeWireless AP560i Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 350-2d AP Bedienungsanleitung

Extreme Networks

Extreme Networks AP410C Bedienungsanleitung

Extreme Networks

Extreme Networks Altitude 3510 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung