Extron electronics Extron P/2 DA2xi Bedienungsanleitung

User’s Guide

P/2 DA2xi and P/2 DA2xi MT • InstallationP/2 DA2xi and P/2 DA2xi MT • Installation

Introduction

Extron Electronics, USA

1230 South Lewis Street

Anaheim, CA 92805

USA

714.491.1500

Fax 714.491.1517

Extron Electronics, Europe

Beeldschermweg 6C

3821 AH Amersfoort

The Netherlands

+31.33.453.4040

Fax +31.33.453.4050

Extron Electronics, Asia

135 Joo Seng Road, #04-01

PM Industrial Building

Singapore 368363

+65.6383.4400

Fax +65.6383.4664

Extron Electronics, Japan

Kyodo Building

16 Ichibancho

Chiyoda-ku, Tokyo 102-0082 Japan

+81.3.3511.7655

Fax +81.3.3511.7656

www.extron.com

The Extron P/2 DA2xi and the P/2 DA2xi MT are distribution

amplifiers that accept video input from a VGA, XGA, or UXGA

compatible PC and distribute the signal to separately buffered

outputs. Each output can be extended with Extron VGA MHR

cables from 6' to 250' in length. The MT model also has audio

input and output.

Features

• Power/Signal LED — Green LED = power + signal.

Amber LED = power but no signal. Off = no power.

• Gain/Peak DIP switch — Use this feature to compensate for

longer cable runs.

• Out Imp DIP switch — Changes the output impedance to be

compatible with all projectors.

• Cable retention chain — The input cable can be secured to the

unit (either model) with the supplied chain (attached to the

right standoff nut of the input VGA connector) to prevent the

cable from becoming lost or misplaced.

MONITOR

AUDIO

INPUT

Installation

The P/2 DA2xi and P/2 DA2xi MT can be mounted on a rack

shelf, under a desk or tabletop, or on a projector bracket.

Rack mounting

For optional rack mounting, mount the P/2 DA2xi or

P/2 DA2xi MT on a 19", 1U RSF 123 VersaTools®rack shelf kit

(part #60-190-20) or a standard RSU 129 1U universal rack shelf

kit (part #60-190-01) as shown in the next figure.

Only products in the VersaTools line can be mounted to a

VersaTools rack shelf.

1. Remove the rubber feet (if installed) and mount the unit on the

rack shelf, using two screws in opposite (diagonal) corners.

2. Install blank panel(s) or other unit(s) to the rack shelf.

3. Insert the shelf into the rack, and secure the shelf to the rack

using the supplied machine screws.

Use 2 mounting holes on

opposite corners.

VersaTools Rack Shelf

1/4 Rack Width False Front

Face Plate

Universal Rack Shelf

DISTRIBUTIONAMPLIFIER

DISTRIBUTIONAMPLIFIERDISTRIBUTIONAMPLIFIER

DISTRIBUTIONAMPLIFIER DISTRIBUTIONAMPLIFIER

DISTRIBUTIONAMPLIFIER

MDASERIES

DISTRIBUTIONAMPLIFIER

Mounting the P/2 DA2xi or P/2 DA2xi MT on a rack shelf

Furniture or projector mounting

For optional furniture or projector mounting, mount the unit

using the mounting kit (part #70-077-01 for furniture [optional

with the P/2 DA2xi, standard with P/2 DA2xi MT] or #70-077-04

for projector [optional with both units]) as follows:

1. Attach the mounting brackets to the distribution amplifier

with the provided machine screws, as shown below.

Ceiling

Digital Projector

Projector

Mounting

Bracket

Mounting

Bolt

INPUTMONITOR

P/2DA2xi

OUTPUT

GAIN/

PEAK

SPARE

EXTPOWER(see manual)

0.1AMAX

Projector and furniture mounting

2. If feet were previously installed on the bottom of the unit,

remove them.

3.For furniture mounting, hold the unit with the attached

brackets against the underside of the table or other

furniture. Mark the location of the screw holes of the

bracket on the mounting surface.

For projector mounting, secure the unit to a projector

mount or other surface by inserting the mounting bolt

through the bracket’s slotted hole.

General

External power supply .................. 100 VAC to 240 VAC, 50/60 Hz, external,

autoswitchable; to 12 VDC, 1 A, regulated

Power input requirements ............ 12 VDC

P/2 DA2x ............................ 0.1 A

P/2 DA2xi MT ................... 0.2 A

Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /

10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) /

10% to 90%, noncondensing

Rack mount ..................................... Yes, with optional 1U rack shelf, part

#60-190-01 or 60-604-01; or VersaTools®rack

shelf, part #60-190-20 or 60-604-20; also

under-furniture mountable with optional

brackets #70-077-01; or projector mountable

with bracket kit #70-077-04 (optional for

P/2 DA2xi, standard for P/2 DA2xi MT)

Enclosure type ................................ Metal

Enclosure dimensions ................... 1.0" H x 4.3" W x 3.0" D (quarter rack wide)

2.5 cm H x 10.9 cm W x 7.6 cm D

(Depth excludes connectors.)

Product weight ............................... 0.5 lbs (0.3 kg)

Shipping weight ............................. 3 lbs (2 kg)

Vibration .......................................... ISTA 1A in carton

(International Safe Transit Association)

Listings ............................................. UL, CUL

Compliances .................................... CE, FCC Class A, VCCI, AS/NZS, ICES

MTBF ................................................ 30,000 hours

Warranty .......................................... 3 years parts and labor

All nominal levels are at ±10%.

Specifications are subject to change without notice.

Distribution Amplifiers

68-713-01 Rev. D

08 05

P/2 DA2xi, P/2 DA2xi MT

FCC Class A Notice

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct the interference at his

own expense.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded

cables must be used with the unit to ensure compliance.

im Vertrieb von

CAMBOARD Electronics

www.camboard.de

Tel. 07131 911201

Fax 07131 911203

[email protected]