Extron electronics TLP Pro x25M Series Bedienungsanleitung

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLP Pro x25M and TLS x25M Series TouchLink Panels

Setup Guide

Overview

The Extron TLP Pro 525M, 725M, and 1025M are three series of wall mounted, capacitive touchscreen, TouchLink®panels with TFT

active matrix color LCD screens with 24-bit color depth.

The TLS 525M, 725M, and 1025M have identical features but use the Room Agent software to coordinate room scheduling.

• The TLP Pro 525M and TLS 525M models have a 5 inch screen with a 800x480 resolution.

• The TLP Pro 725M and TLS 725M models have a 7 inch screen with a 1024x600 resolution.

• The TLP Pro 1025M and TLS 1025M models have a 10.1 inch screen with a 1280x800 resolution.

This guide provides instructions for experienced installers to mount and install these TouchLink panels.

Setup Checklist

Get Ready

Download and install the latest version of the following software onto the PC being used to congure the TouchLink panel:

Toolbelt — Provides device discovery, device information, rmware updates, and conguration of network settings, system

utilities, and user management for TouchLink Pro devices and scheduling panels.

TLP Pro touchpanels

GUI Designer — For designing layouts for Extron TouchLink Pro touchpanels and third party touch interfaces.

Global Configurator®Professional and Global Configurator Plus — For setting up and conguring the control processor

and TouchLink panel.

Global Scripter®— Provides an integrated development environment for Extron control systems programming.

TLS scheduling panels

Room Agent™ — Free room booking software for conguring the panels for room scheduling.

NOTE: All ve software programs and supporting documentation are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status — (on or off). If DHCP is off, you must also obtain:

IP address Subnet mask Gateway

User name — This can be either admin or user.

Password — The factory congured passwords for all accounts on this device have been set to the device serial number.

Passwords can be changed during conguration. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the password is the default password conguration. The default

password is extron (for either admin or user).

Make a note of the TouchLink panel MAC address, which can be found on a rear-panel label.

Mount and Cable All Devices

ATTENTION:

• Do not power on the TouchLink panels until you have read the Attention in the “Rear Panel Features” section of the

TLP Pro 525, 725, and 1025 Series User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section «Rear Panel Features » du

TLP Pro 525, 725, and 1025 Series User Guide.

Mount the units. There are several mounting options for TouchLink panels (see Mounting on the next page).

Connect the TouchLink panel to a Power over Ethernet injector (see ﬁgure 5 on page 5).

Connect the power injector to the LAN and power it on (ﬁgure 5).

Set up the TouchLink Panels for Network Communication

Connect the PC that you are using for setup, the control processor, and the touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see page 6) or Toolbelt to set the DHCP status and, if required, network addresses for the TouchLink

panel.

www.extron.com

TLP Pro x25M and TLS x25M Series TouchLink panels • Setup Guide (Continued)

Conﬁgure the TouchLink Panels

TLP Pro TouchLink panels — The GUI Designer Help File, the Global Conﬁgurator Help File, and the Toolbelt Help File provide

step-by-step instructions and detailed information, including an introduction to the software and sections on how to start a project

and conguration.

Global Scripter provides an Extron-exclusive Python library (ControlScript®) and Global Scripter modules to get you started (see the

Global Scripter Help File).

TLS scheduling panels — The Room Agent Help File, User Guide, and Quick Start Guide provide information about conguring these

panels.

Mounting

All these panels can be wall-mounted, either using a UL-listed junction box, an external wall box, or directly into drywall or furniture.

Suitable mounting accessories can be found at www.extron.com.

ATTENTION:

• Do not install TouchLink panels in a re resistant rated wall or partition assembly.

• Veuillez ne pas installer les écrans TouchLink dans un mur protégé par un dispositif coupe-feu ou dans une cloison.

• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and

national building codes and electrical codes.

• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux

codes du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.

With a Wall Box or Junction Box

Some local building codes require the TouchLink panel to be mounted in a junction box. Junction boxes or wall boxes must be

purchased separately. Figure 1 shows the TLP Pro 725M. Installation for the other panels is very similar.

NOTES:

• The 5 inch models mount to a 1-gang junction box. The

US 1-gang junction box should be installed so that the

long side is horizontal. EU or MK 1-gang junction boxes

should be installed in the standard orientation.

• The 7 and 10 inch models mount to a 2-gang junction

box.

• Extron provides four 3/4" #6-32 Philips pan head screws

for mounting to US junction boxes

• Extron provides two 16 mm M 3.5 Philips pan head

screws for mounting to MK junction boxes

• EU junction boxes are usually provided with their own

screws.

With a wall box

1. Install a junction box or wall box (see gure 1, 1),

following the instructions provided by the manufacturer.

2. Fasten the mounting plate to the wallbox (2) with

the provided screws. Use the mounting holes that

are appropriate to the junction box you are using (see

ﬁgure 2 on the following page).

3. Run and connect cables to the back of the TouchLink

panel (see Rear Panel Features on the following page).

4. The mounting plate for the 5 inch TouchLink panel has

two hooks (one in each top corner). The mounting plate

for the 7 and 10 inch panels has four hooks (3), one in

each corner (see ﬁgure 2).

Position the touch panel so that the mounting slots (see

ﬁgure 4,D, on page 4) in the rear of the TouchLink

panel align with these hooks.

5. Move the TouchLink panel inward and downward so that

the panel sits securely on the hooks, and the tongue at

the bottom of the mounting plate (4) sits in the groove

in the bottom of the panel (see inset, gure 1, 5).

6. Fasten the TouchLink panel to the mounting plate with

the lock screw (6).

steps 3 through 6

TOP

Back View

Figure 1. Mounting the TLP Pro 725M with a Junction Box

gure 1

Product Category

NORTH

AMERICA

NORTH

AMERI

EU/MK EU/MK

WALL

NORTH

AMERICA

NORTH

AMERICA

NORTH

AMERICA

NORTH

AMERICA

EU EU

Figure 2. Mounting Plates for 5 inch models (left) and 7 or 10 inch models (right)

NOTE: The TLP Pro 725M, TLS 725M, TLP Pro 1025M, and TLS 1025M TouchLink panels use the same mounting plate.

Without a wall box

If the wall box is not required by local building codes, you can mount the TouchLink panel directly into drywall.

1. Use the mounting plate as a template to mark the wall or download the cut-out template for your product from www.extron.com.

Place the template or mounting plate against the wall or furniture in a suitable location and ensure that it is level.

2. Mark the position of the hole and cut the wall.

• For the 5 inch models, this hole is 2.4 inches (61 mm) wide x 2.1 inches (53 mm) high.

• For the 7 or 10 inch models, this hole is 3.5 inches (89 mm) wide x 2.0 inches (51 mm) high.

3. Mark the slots labeled WALL (5 inch models) or MK (7 or 10 inch models) (see gure 2) and drill the two pilot holes. Extron

recommends using two Molly bolts or SnapToggle bolts.

4. Secure the mounting plate to the wall (see ﬁgure 1, 2, on the previous page).

5. Complete the installation as described in steps 3 through 6 on the previous page.

gure 2

Front Panel Features

NOTE: Figure 3 shows the front panel of the TLP Pro 725M.

The front panels of all the TouchLink panels have the same

features and are almost identical apart from the size.

AMotion sensor — Detects motion between three to ve feet

from the TouchLink panel, and at least 15° from the center

axis.

• If the sleep timer has been set (see Setup Menu on

page 6), and no motion has been detected for a

user-dened period of time, the TouchLink panel enters

sleep mode.

• If Wake on Motion has been set (see Setup Menu), and

motion is detected by the sensor while the screen is in

sleep mode, the screen display is restored and active.

Extron

E E

Figure 3. TLP Pro 725M Front Panel

BCommunication LED — (TLP Pro models only) Shows the conguration and connection status of the touchpanel:

• Unlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).

• Blinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.

• Lights steadily red if the touchpanel has not been congured.

The indicator can be toggled between enabled and disabled, using the Setup Menu.

CLight sensor — Monitors ambient light level and adjusts screen brightness.

DCapacitive touchscreen

• The TLP Pro 525M series and TLS 525M have a 5 inch screen with a 800x480 resolution.

• The TLP Pro 725M series and TLS 725M have a 7 inch screen with a 1024x600 resolution.

• The TLP Pro 1025M series and TLS 1025M have a 10.1 inch screen with a 1280x800 resolution

gure 3

TLP Pro x25M and TLS x25M Series TouchLink panels • Setup Guide (Continued)

Rear Panel Features

TLP Pro 525M I

I J

TLP Pro 725M

I J

JTLP Pro 1025M

Figure 4. TLP Pro 525M, 725M, and 1025M Rear Panels

gure 4

NOTES:

• The panels shown in gure 4 are for illustration

only and are not to the same scale.

• The TLS models have the same rear panel

features as the corresponding TLP Pro models.

For more information, follow these links to the next page.

AMenu Button

BReset Button

CReset LED

DMounting Slots

EDigital Input Monitoring Port

FLAN/PoE Connector

GUSB Port

HSpeaker

ISlot for Mounting Plate

JMounting Screw

KRear Panel Status Lights

EStatus lights — Two LED light bars, one on either side of the screen (see ﬁgure 3 on the previous page).

TLS models — The LEDs light green when the room is currently available and red when the room is currently booked. They

cannot be programmed.

TLP Pro models — The LEDs can be congured to light red or green and to blink or light continuously, to provide system

feedback (see the Global Conﬁgurator Help File and Global Scripter Help File).

Product Category

AMENU Button (see ﬁgure 4 on the previous page)— Activates the setup menu (see Setup Menu on the next page).

BRESET Button — Pressing the Reset button allows the unit to be reset in any of three different modes (for an overview, see

Reset Modes, on the next page).

CRESET LED — Provides feedback about the reset status when the user presses the Reset button (see Reset Modes).

DMounting Slots — The TLP Pro 725M and TLP Pro 1025M have four, one in each corner. The TLP Pro 525M has two, one in each

top corner. The hooks on the corners of the mounting plate (see ﬁgure 1, 3on page 2) t into these slots for wall mounting.

EDigital Input Monitoring Port — This two-pole captive screw port (1= signal and G= ground) monitors digital input with or

without a +5 VDC pull-up.

FLAN/PoE Connector — Connect the TouchLink panel to a PoE power injector (not provided) using a twisted pair cable,

terminated with an RJ-45 connector. Connect the power injector to the LAN through a nework switch. An Extron IP Link Pro

control processor must also be connected to the same network as the TouchLink Pro touchpanel. TLS models do not require a

control processor

ATTENTION:

• The TouchLink panels are Power over Ethernet (PoE 802.3af, class 3) compliant. Do not power on the touchpanels

until you have read the Attention in the “Rear Panel Features” section of the TLP Pro 525, 725, and 1025 Series

User Guide.

• Les écrans TouchLink supportent l’alimentation via Ethernet (PoE 802.3af, classe 3). Veuillez lire la partie

« Attention » dans la section « Rear Panel Features » du TLP Pro 525, 725, and 1025 Series User Guide, avant de

mettre sous tension les écrans tactiles.

NOTE: These TouchLink panels are shipped without a power

injector. The power injector must be purchased separately.

Menu Button

Reset Button

Reset LED

Mounting Slots

Digital Input Monitoring Port

LAN/PoE Connector

Extron recommends the Extron XTP PI 100 power injector (see gure 5).

Your power injector may look different.

GUSB Port — Compatible with USB 2.0.

HSpeaker — Provides audible feedback for the user.

• TLP Pro 525M and TLS 525M — a single speaker

• TLP Pro 725M and TLS 725M — a single speaker

• TLP Pro 1025M and TLS 1025M — two (dual mono) speakers

USB Port

Speaker

100-240V

50-60Hz

0.4A MAX

XTP

PWR

XTP PWR

To network switchTo TouchLink panel

Figure 5. XTP PI 100 Power Injector

gure 5

ISlot for Mounting Plate — The tongue at the bottom of the mounting plate (see ﬁgure 1, 4) ts into this slot, for wall mounting.

JMounting Screw — Tightens against the tongue of the mounting plate to secure the TouchLink panel.

KRear Panel Status Lights — These lights can be disabled for glass mount applications.

• TLP Pro 525M and TLS 525M — no lights

• TLP Pro 725M and TLS 725M — Six lights, three on each side of the panel

• TLP Pro 1025M and TLS 1025M — Two lights, one on each side of the panel

TLS models — The LEDs light green when the room is currently available and red when the room is currently booked. They

cannot be programmed.

TLP Pro models — The LEDs can be congured to light red or green and to blink or light continuously, to provide system

feedback.

The rear panel status lights can be toggled between enabled and disabled by using the Setup Menu (see the next page).

For information about programming these LEDs for the TLP Pro x25M models, see the Global Conﬁgurator Help File and Global

Scripter Help File.

Mounting Screw

Slot for Mounting Plate

Rear Panel Status Lights

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

TLP Pro x25M and TLS x25M Series TouchLink panels • Setup Guide (Continued)

Reset Modes: a Brief Summary

These TouchLink panels provide the following reset modes (see the TLP Pro 525, 725, and 1025 Series User Guide for complete

information):

• Use Factory Firmware — With the unit powered off, press and hold the RESET button (see ﬁgure 4, Bon page 4) while

reapplying power to the unit. Use this mode with Toolbelt software to replace rmware in the event of conicts arising from

uploading a rmware update.

• Reset All IP Settings — Press and hold the RESET button for 6 seconds. After the RESET LED (C) blinks twice, release and

momentarily press the RESET button. Use this mode to reset all network settings without affecting user-loaded les.

• Reset to Factory Defaults — Press and hold the RESET button for 9 seconds. After the Reset LED blinks three times, release

and momentarily press the RESET button. Use this mode to return the TouchLink panel to factory default settings.

NOTES:

• The factory congured passwords for all accounts on this device have been set to the device serial number.

Passwords are case sensitive.

• If the device is reset to default settings, the password will be the default password conguration. The default

password is extron (for either admin or user).

• Enable or Disable the DHCP Client — This mode toggles between DHCP enabled and DHCP disabled. Press the Reset

button ve times, consecutively. After the fth press, do not press the button again within 3 seconds. If DHCP was enabled, it

is now disabled and the Power LED blinks three times. If DHCP was disabled, it is now enabled and the Power LED blinks six

times.

Reset Modes

Status DisplayAudioAdvanced Exit

Network

Info

Model: TLP Pro 725M

Part Number: 60-1563-02

Firmware

Version:1.02.0001-b001

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

GUI Project:

Sleep Timer:

1024x600

N/A

5 Minutes

Audio

System Volume:

System Mute: Off

Advanced

Controller IP:N/A

Project Size: N/A

Bootloader

Version:1.03.0000

Figure 6. Setup Menu: Status Screen for TLP Pro 725M

Setup Menu

Figure 6 shows the Status screen for the TLP Pro 725M. The

screen for the TLP Pro 525M, TLP Pro 1025M, and the TLS

models are similar.

Press the MENU button (ﬁgure 4, A) to open the setup menu.

Select any of the ve available screens (Status, Network,

Display, Audio, and Advanced) by pressing the appropriate

button in the navigation bar at the top of the screen (for more

information, see the TLP Pro 525, 725, and 1025 Series User

Guide).

68-2831-55 Rev. B

10 21

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Bedienfeld Handbücher

Extron electronics

Extron electronics RCP 2000 Bedienungsanleitung

Extron electronics

Extron electronics MMX 32 AAP Bedienungsanleitung

Extron electronics

Extron electronics ACP 100 Bedienungsanleitung

Extron electronics

Extron electronics ACP 105 EU/MK Bedienungsanleitung

Extron electronics

Extron electronics Decorator-Style Series Bedienungsanleitung

Extron electronics

Extron electronics RCP 2000 Bedienungsanleitung

Extron electronics

Extron electronics ACP 100 Bedienungsanleitung

Extron electronics

Extron electronics ACP 106 D Bedienungsanleitung

Extron electronics

Extron electronics SCP 150L Bedienungsanleitung

Extron electronics

Extron electronics ACP VCI EU/MK Bedienungsanleitung

Extron electronics

Extron electronics TouchLink Pro Series Bedienungsanleitung

Extron electronics

Extron electronics SCP 104 Series Bedienungsanleitung

Extron electronics

Extron electronics MKP 2000 Bedienungsanleitung

Extron electronics

Extron electronics IP Link Pro NBP 50 Bedienungsanleitung

Extron electronics

Extron electronics AAP 100 Bedienungsanleitung

Extron electronics

Extron electronics MKP 3000 Bedienungsanleitung

Extron electronics

Extron electronics ACP 105 D Bedienungsanleitung

Extron electronics

Extron electronics NBP 100 Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 320C Bedienungsanleitung

Extron electronics

Extron electronics MLC 55 RS Bedienungsanleitung

Extron electronics

Extron electronics eBUS Button Panel EU Series Bedienungsanleitung

Extron electronics

Extron electronics ACP VC1 D Bedienungsanleitung

Extron electronics

Extron electronics RCP 101 EU Bedienungsanleitung

Extron electronics

Extron electronics eBUS Button Panel Decorator-Style Series Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten