Extron electronics CCD 220 Bedienungsanleitung
1
CCD 220
CCD 320
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
Cable Cubby Drawer CCD 220 and CCD 320 •
Installation Guide
This guide provides instructions for an experienced technician to
install and connect the Extron Cable Cubby Drawer CCD 220 and
CCD 320.
The Cable Cubby Drawers (CCD) are cable access sliding
products that mount underneath furniture for AV connectivity,
control, and power.
Planning
Check with local and state regulations before starting the installation
Ensure that the planned installation complies with national and local building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility
requirements.
Check all parts and equipment before installation
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
Kit Contents
CCD 220 CCD 320
#8 pan-head wood screws 10 #8 pan-head wood screws 10
Cable tie-wraps 6 Cable tie-wraps 10
Tweeker 1 Tweeker 1
HDMI VGA AUDIO USB
USBCHARGER
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
2
Application Diagram
HDMI VGA AUDIO USB
USBCHARGER
HDMI VGA AUDIO USB
USBCHARGER
Extron
CCD 220
3
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
Preparing the Table
Determine the best location to install the Cable Cubby Drawer
Ensure that the location where the Cable Cubby Drawer will be installed is convenient for the user.
Ensure that there is ample space under the table to allow for cable management. Reposition the cable track if
space is limited (see Reposition Cable Track on the next page for instructions).
22.42"
(569.5 mm)
12.21"
(310.4 mm)
9.19"
(233.4 mm)
CCD 220 Top View
22.42"
(569.5 mm)
24.21"
(614.9 mm) 21.19"
(538.2 mm)
CCD 320 Top View
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
4
Optional: Reposition Cable Track if Necessary
The drawer’s cable track can be respositioned if space underneath the table is limited.
There are two options to reposition the drawer:
NOTE: Before mounting the CCD, open and
close the drawer several times to test for
cable bend issues or resistance.
Option 2: Relocate the cable track to the other side of the Cable Cubby Drawer
.
Perform the same action as in Option 1 and r
emove the cable track bridge arm.
1Remove the three cable
track screws located behind
the cable track mounting U
bracket.
2 Remove the three nuts and
washers holding the cable track
in place.
U bracket
1
1
Option 1: Reposition the rear cable track by removing the fixed-length cable track bridge arm.
1Remove the seven screws
holding the bridge arm and
cable track together.
2Remove the bridge arm
from its place to allow the
cable track to be repositioned.
Cable Track
Bridge Arm
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
5
Reattach the U bracket
to the Cable Track unit.
3
Remove the chain
mounting feet fr
om
the cable track unit
with the included
tweeker
.
4Turn the cable track
unit 180º clockwise.
5Flip both mounting feet
so they face the drawer,
and re
attach to the cable track unit.
6Reattach all mounting
hardware removed in
steps 1 through 3 to
the other side of
the cable track.
7If there is adequate space, reassemble
the bridge arm before mounting
the Cable Cubby Drawer to the table.
Pre-drill mounting holes for the Cable Cubby Drawer
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
ATTENTION : Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
The following instructions apply to both the CCD 220 and CCD 320.
1. Align the included template (the dimensions can also be found on the next two pages) so the front edge of
the template is ush with the edge of the mounting surface. This is where the drawer will open and close.
2. Tape the template if necessary and mark the center of the holes where the Cable Cubby Drawer will be
installed.
3. Drill 3/32”(2.38 mm) diameter pilot holes for the included #8 wood screws, 1/2”(12.7 mm) deep where you
have marked the holes.
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
6
CCD 220
Mounting
Template
Instructions
1. Align the template so that the “Table Edge”
of the template is ushed with the edge of
the mounting surface.
2. Mark the center of the holes and drill
pilot holes 3/32" (2.38 mm) diameter,
1/2" (12.7 mm) inch deep.
22.01"
(559.1 mm
)
1.00"
(25.4 mm)
Table Edge
10.70"
(271.8 mm)
12.21"
(310.1 mm)
0.75"
(19.1 mm)
1.00"
(25.4 mm)
20.64"
(524.3 mm)
1.00"
(25.4 mm)
3.85"
(97.9 mm)
12.35"
(313.8 mm)
Pilot drill 3/32" (2.38 mm) diameter holes,
1/2" (12.7 mm) inch deep
(12 places).
NOTE: The diagram below is not drawn to scale.
Dimensions and templates are available online at
www.extron.com.
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
7
NOTE: The diagram below is not drawn to scale.
Dimensions and templates are available online at
www.extron.com.
24.21"
(614.9 mm)
1.00"
(25.4 mm)
20.64"
(524.3 mm)
22.01"
(559.1 mm)
3.85"
(97.9 mm)
0.75"
(19.1 mm)
22.70"
(576.6 mm)
12.35"
(313.8 mm)
CCD 320
Mounting Template
Instructions
1. Align the template so that the “Table Edge”of the template
is ushed with the edge of the mounting surface.
2. Mark the center of the holes and drill pilot holes 3/32" (2.38 mm) diameter
,
1/2" (12.7 mm) inch deep.
TABLE
EDGE
Pilot drill 3/32" (2.4 mm) diameter holes,
1/2" (12.7 mm) inch deep
(12 places).
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
8
Preparing the Cable Cubby Drawer
Step 1 — Disassemble the AAP frame from the Cable Cubby Drawer
1 Remove the bottom screws from
underneath the drawer (3 screws for
the CCD 220 and 5 for the CCD 320).
2
Remove each screw from the
side of the drawer and lift the AAP
frame up and out.
AAP Frame
Step 2 — Attach the AAP modules to the AAP frame
AAP frames allow you to populate the Cable Cubby Drawer with a combination of AAP modules. Follow the steps
below to assemble the connectivity modules of your choice.
HDMI VGA AUDIO USB
USB CHARGER
3 Position the AAP modules thr
ough
the front of the AAP frame.
4
Secure the AAP modules
with the #4-40 nuts included
with the AAP kits
Step 3 — Install Populated AAP frame onto the Cable Cubby Drawer
HDMI VGA AUDIO USB
USB CHARGER
5 Reposition and secure the AAP frame
back onto the Cable Cubby Drawer
using the screws removed in Step 1.
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
9
1 Remove the screws holding
the facade to the drawer.
2 Once modied, reattach the facade
to the drawer by using the same scr
ews
removed from Step 1.
Or use the proper hardware or
adhesive for the new facade material
Step 4: Mounting a Power Supply to the CCD 320 (Optional)
Place one or two power supplies behind the AAP modules as seen in the image below.
A power supply can be mounted in either location or orientation by lining up the mounting holes.
Step 5: Customize the Front Façade (Optional)
Renish, paint, or add veneer to the façade to complement the furniture, or fabricate a new facade using the
dimensions seen on the next page.
1 Install #4-40 mounting screws through
the bottom holes to secure the power supply.
Cable Cubby Drawer CCD 220 and CCD 320 • Installation Guide (Continued)
10
Route the Cables from the AAP Modules and through the Cable Track
8.16"
(207.2 mm)
CCD 220 Front View
CCD 220 Side View
1.49"
(37.8 mm)
0.20"
(5.0 mm)
R= 0.49"
(1.3 mm)
R= 0.49"
(1.3 mm)
R= 0.49"
(1.3 mm) R= 0.59"
(1.5 mm)
2X 125°
20.16"
(512.0 mm)
1.49"
(37.8 mm)
0.20"
(5.0 mm)
R= 0.49"
(1.3 mm)
R= 0.49"
(1.3 mm)
R= 0.49"
(1.3 mm)
R= 0.59"
(1.5 mm)
2X 125°
CCD 320 Front View CCD 320 Side View
Figure 1 CCD 220 and CCD 320 Front Facade Dimensions
1
Open the cable track by using
the included tweeker to pry open
the aps.
Do this to the entir
e cable track.
11
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Extron electronics Gehäuse Handbücher
Extron electronics
Extron electronics PowerCage 1600 Bedienungsanleitung
Extron electronics
Extron electronics SMB 110 Series Bedienungsanleitung
Extron electronics
Extron electronics Cable Cubby 202 Bedienungsanleitung
Extron electronics
Extron electronics TLM 100 T Bedienungsanleitung
Extron electronics
Extron electronics MLM-WB Bedienungsanleitung
Extron electronics
Extron electronics MediaLink MLM-WB+ Bedienungsanleitung
Extron electronics
Extron electronics PowerCage 1600 Bedienungsanleitung
Extron electronics
Extron electronics Cable Cubby F55 Edge Bedienungsanleitung
Extron electronics
Extron electronics HSA 400 Series Bedienungsanleitung
Extron electronics
Extron electronics EWB 212 Bedienungsanleitung
Extron electronics
Extron electronics Cable Cubby 500 Bedienungsanleitung
Extron electronics
Extron electronics EWB 112 Bedienungsanleitung
Extron electronics
Extron electronics CS 120P Bedienungsanleitung
Extron electronics
Extron electronics Hideaway HSA 200C Series Bedienungsanleitung
Extron electronics
Extron electronics PowerCage 401 Bedienungsanleitung
Extron electronics
Extron electronics HSA 822M Bedienungsanleitung
Extron electronics
Extron electronics HSA 200SE Bedienungsanleitung
Extron electronics
Extron electronics PowerCage 1600 Bedienungsanleitung
Extron electronics
Extron electronics HSA 822 Bedienungsanleitung
Extron electronics
Extron electronics Cable Cubby 300S Bedienungsanleitung
