Extron electronics XTP II CrossPoint Series Bedienungsanleitung

XTP II CrossPoint Series • Setup Guide

The XTP II CrossPoint Series matrix switchers route multiple signals between multiple local and remote sources and display

devices. This guide provides instructions for an experienced installer to install and connect any XTP II CrossPoint matrix switcher.

The different matrix switcher models share the same basic features

but they may be arranged differently.

• XTP II CrossPoint 1600 — Supports up to four input and four

output boards in horizontal slots.

• XTP II CrossPoint 3200 — Supports up to eight input and eight

output boards in vertical slots.

• XTP II CrossPoint 6400 — Supports up to 16 input and 16

output boards in vertical slots.

Figure 1 shows the rear panel features of an XTP II CrossPoint 3200

matrix switcher but they apply to the other matrix switcher models.

Board Space Enclosure Features

A Input board space

B Output board space

See “Board and Blank

Plate Installation” below

for details.

C RS-232 and RS-422 connector

D Ethernet LAN connector

E Reset button and LED

F AC power connector

See Rear Panel Features on the next

page for details.

100-240V

50-60Hz

12A MAX

DISCONNECT POWER

CORD BEFORE

SERVICING

1-45-8 9-12 13-16

INPUTS

17-20 21-24 25-28 29-32 1-45-8 9-12 13-16

OUTPUTS

17-20 21-24 25-28 29-32

XTP CROSSPOINT 3200

1591317212529

4812 16 20 24 28 32

15913172125

4812 16 20 24 28 32

RESET

REMOTE

LAN

RS-232/422

XTP II CrossPoint 3200

Installation

Board and Blank Plate Installation

Changing the boards changes the conguration of the matrix switcher. All boards are hot-swappable and can be installed without

removing power to the matrix switcher. Ensure a board or blank plate is installed in every slot (see gure 1, Aand B).

ATTENTION: Do not touch the electronic components or the connectors on the backplane or on the circuit

boards without being electrically grounded. Handle circuit boards by their edges only.

Removal

1. For boards, disconnect connected cables.

2. Loosen the two knobs on the board or blank plate until the screws

attaching the board are separated from the enclosure.

3. For boards, gently pull the knobs away from the enclosure to

dislodge the board from the enclosure.

4. Slide the board or pull the plate out of the slot. Place boards on

an anti-static surface or in an anti-static container.

Installation

1. If another board or blank plate interferes with the installation of a

new board, remove it (see Removal).

2. For boards, slide the board in the slot along the guides and rmly

push it into the enclosure so the panel is ush with the enclosure.

3. Tighten the two knobs on each end of the board or blank plate to

secure it to the enclosure.

LAN

ACT

LINK

RESET

100-240V

50-60Hz

--AMAX

REMOTE

RS232/RS422

DISCONNECTPOWER

CORDBEFORE

SERVICING

XTPCP 4o HDMIAUDIO

LR LR LR LR

XTPCP 4o HDMIAUDIO

LR LR LR LR

XTPCP 4o HDMIAUDIO

LR LR LR LR

XTPCP 4o HDMIAUDIO

LR LR LR LR

XTPCP 4o HDMIAUDIO

LR LR LR LR

XTPCP 4o HDMIAUDIO

LR LR LR LR

XTPCP 4i HDMIAUDIO

LR LR LR LR

XTPCP 4i HDMIAUDIO

LR LR LR LR

XTPCP 4o HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4i HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4i HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4i HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4o HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4o HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4i HDMIAUDIO

LR LR LR LR

OUT

XTPCP 4o HDMIAUDIO

LR LR LR LR

OUTPUT

XTP II CrossPoint 3200

Knobs

Align with

Plastic Guides

90 °

INPUTS

OUTPUTS

100-240V

50-60Hz

--A MAX

1−4

5−8

9−12

13−16

1−4

5−8

9−12

13−16

LAN

ACT LINK

REMOTE

RS-232/RS-422

OUT

SIG LINK

XTP

PWR

ACT LINK

LAN

SIG LINK

XTP

PWR

ACT LINK

LAN

PWR

RL R

XTPCP 4o DVI Pro

OUT

SIG LINK

XTP

PWR

ACT LINK

LAN

SIG LINK

XTP

PWR

ACT LINK

LAN

SIG LINK

XTP

PWR

ACT LINK

LAN

OUT

ACT LINK

LAN

XTPCP 4o HDMI

AUDIO

L R L R L R L R

OUTPUTS

Align with

Plastic Guides

Knobs

XTP II CrossPoint 1600

90 °

Figure 1. XTP II CrossPoint Matrix Switcher

Rear Panel Features

XTP II CrossPoint Series • Setup Guide (Continued)

Mounting

Use screws on each side of the matrix switcher to attach the front panel to a rack (see the XTP II CrossPoint Series User Guide at

www.extron.com for more mounting information).

Rear Panel Features

CRemote RS-232 and RS-422 connector (see figure 1 on the previous page)

— For RS-232 or RS-422 serial control of the matrix switcher, connect a host

device to the 9-pin HD connector. Wire the connector for RS-232 or RS-422

communication as shown to the right.

DEthernet LAN connector — For 10/100BASE-T, half duplex or full duplex

Ethernet control of the matrix switcher, connect a host device, LAN, or WAN

to the RJ-45 connector with crossover or patch cable.

Default protocol for this port:

• IP address = 192.168.254.254

• Subnet mask = 255.255.0.0

• Gateway address = 0.0.0.0

EReset button and LED — Hold the recessed reset button in to perform various resets (see the XTP II CrossPoint Series User

Guide for more information about reset modes).

FPower connector — Connect a power source to the AC power connector.

• AC Power — Connect a 100 VAC to 240 VAC, 50-60 Hz power source to this connector with a standard

IEC power cord.

• Attached AC power (XTP II CrossPoint 6400 only)

• North America — Connect the power cord into a NEMA L6-20 220VAC, 60 Hz power outlet.

• Other regions — Have a licensed electrician install a 200-240 VAC power connector. Then, connect

the power cord into a 200-240 VAC, 50-60 Hz power outlet. Ensure the wiring is in accordance with

electrical codes.

ATTENTION: Extron recommends that this procedure be performed by a licensed electrician only (see the

XTP II CrossPoint Series User Guide).

Board Connections

The available connectors depend on the board models. The following connector information represents potential connectors

included with input and output boards.

XTP interconnection connectors

XTP twisted pair, 4K twisted pair, and fiber boards may include the following connectors:

• XTP twisted pair input connectors — Connect a shielded twisted pair cable between the XTP input connector on the input

board and the XTP output connector on an XTP twisted pair device (see Twisted pair recommendations on the next page).

• XTP twisted pair output connectors — Connect a shielded twisted pair cable between the XTP output connector on the

output board and the XTP input connector on an XTP twisted pair device (see Twisted pair recommendations).

• XTP fiber input connectors — Connect a fiber optic cable between the XTP input connector on the input board and the XTP

output connector on an XTP fiber device (see Fiber communication on page 4).

• XTP fiber output connectors — Connect a fiber optic cable between the XTP output connector on the output board and the

XTP input connector on an XTP fiber device (see Fiber communication on page 4).

• Pass-through LAN connectors — Connect a control device or device to control to the RJ-45 connector with crossover or

patch cable to pass 10/100BASE-T Ethernet communication.

• RS-232 and IR Over XTP — To pass bidirectional serial or infrared signals to a control

device or device to control, connect the device to the RS-232 and IR Over XTP connector.

Wire the connector as shown to the right.

L6-20R

North America

Hot Y: Hot

G: Ground

Pin RS-232 RS-422

RS-232 FunctionPin Function

—

Gnd

—

Not used

Transmit data

Receive data

Not used

Signal ground

Not used

—

TX–

RX–

—

Gnd

—

RX+

TX+

—

Not used

Transmit data (–)

Receive data (–)

Not used

Signal ground

Not used

Receive data (+)

Transmit data (+)

Not used

RS-422

REMOTE

RS 232/RS422

2 Tx Tx-

3 Rx Rx-

5 Gnd Gnd

7 Rx+

8 Tx+

Input connectors

Input boards for local sources may include the following connectors:

• HDMI input connectors — Connect a digital video source to a female HDMI input connector. It can accept HDMI, DVI (with

an appropriate adapter), or dual mode DisplayPort video signals.

NOTE: Use an Extron LockIt®Lacing Bracket to secure HDMI cables to the rear panel connectors.

• DVI input connectors — Connect a digital video source to a female DVI input connector.

• SDI input and Loop Out connectors — Connect a 3G-SDI, HD-SDI, or SDI video source to a BNC input connector. For each

input, connect an optional digital display for local output of the source on the corresponding BNC Loop Out connector.

NOTE: Use 75 ohm terminators on unused Loop Out connectors.

• VGA input connectors — Connect an analog RGB video source to a female 15-pin HD VGA connector.

• Analog audio input connectors — Connect

balanced or unbalanced stereo audio to a 3.5 mm,

5-pole captive screw connector. Wire the connector

as shown to the right.

Output connectors

Output boards for local output devices may include the following connectors:

• HDMI output connectors — Connect a digital video display to a female HDMI output connector.

NOTE: Use an Extron LockIt®Lacing Bracket to secure HDMI cables to the rear panel connectors.

• DVI output connectors — Connect a digital video display to a female DVI output connector.

• Analog audio output connectors — Connect

a balanced or unbalanced, stereo or mono

audio device to a 3.5 mm, 5-pole captive screw

connector for 2-channel stereo analog audio.

Wire the connector as shown to the right.

Connection Details

Twisted pair recommendations for XTP communication

ATTENTION: Do not connect this connector to a computer data or telecommunications network.

The twisted pair input and output boards are compatible with shielded twisted pair (F/UTP, SF/UTP, and S/FTP) cable. Extron

recommends using the following practices to achieve full transmission distances up to 330 feet (100 meters) and reduce

transmission errors.

• Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron recommends 24 AWG, solid

conductor, STP cable with a minimum bandwidth of 400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard.

• Limit the use of more than two pass-through points, which may include patch points,

punch down connectors, couplers, and power injectors. If these pass-through points are

required, use shielded couplers and punch down connectors.

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the

following:

• Do not exceed 40% ll capacity in conduits.

• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned,

and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

Do not tin

the wires!

Unbalanced Stereo InputBalanced Stereo Input

Tip

Ring

Tip

Ring

Slee

ves

Tip

Sleeve

Tip

Do not tin

the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

TIA/EIA-T568B

Pin Wire Color

1White-orange

2Orange

3White-green

4Blue

5White-blue

6Green

7White-brown

8Brown

12345678

RJ-45

Connector

Insert Twisted

Pair Wires

Pins:

68-1736-51

Rev. D

01 19

Fiber communication

WARNING: Potential risk of severe injury. The ber optic devices output continuous invisible light (class 1 rated), which

may be harmful to the eyes; use with caution.

•Do not look into the ber optic cable connectors or into the ber optic cables themselves.

•Plug the attached dust caps into the optical transceivers when the ber optic cable is unplugged.

Operation

After the XTP devices and all connected devices are properly connected and powered on, the system is fully operational.

To locally manage ties and presets, adjust audio levels, or set various other settings, use the front panel buttons (see the

XTP II CrossPoint Series User Guide at www.extron.com for front panel operation features and procedures). To congure and

control the matrix switcher remotely, use one of the following methods.

XTP System Conﬁguration Software

The Extron XTP System Conguration Software (recommended) provides a graphical interface to congure and control the matrix

switcher and connected XTP devices. To use the software:

1. Download the software from www.extron.com and install it on a PC with a Windows®operating system.

2. Connect the PC to the front panel USB conguration connector or a network connected to the Ethernet LAN connector.

3. For more information about the software, open the software and click Help from the Help menu.

SIS Commands

Simple Instruction Set (SIS™) commands congure and control the matrix switcher and connected XTP devices. To enter SIS

commands through the matrix switcher:

1. Download the Extron DataViewer utility from www.extron.com and install it on a PC with a Windows operating system.

2. Connect the PC to the front panel USB conguration connector, a network connected tot he rear panel Ethernet LAN

connector, or rear panel RS-232 and RS-422 connector.

3. For a list of SIS commands and expected responses, see the XTP II CrossPoint Series User Guide at www.extron.com.

Internal Web Pages

The internal web pages allow conguration and control of the matrix switcher through a network. To use the internal web pages:

1. Connect a PC to the same network connected to the Ethernet LAN connector on the matrix switcher.

2. Open a web browser and enter the IP address of the matrix switcher in the browser Address eld.

3. Press the <Enter> key on the keyboard (see the XTP II CrossPoint Series User Guide at www.extron.com).

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92905, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

Andere Handbücher für XTP II CrossPoint Series

Dieses Handbuch passt für folgende Modelle

Andere Extron electronics Matrix-Umschalter Handbücher

Extron electronics

Extron electronics MAV Plus 128 A Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Bedienungsanleitung

Extron electronics

Extron electronics DXP Series Bedienungsanleitung

Extron electronics

Extron electronics ISM 482 Bedienungsanleitung

Extron electronics

Extron electronics MPX 423 A Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 300 Series Bedienungsanleitung

Extron electronics

Extron electronics MPX 423 A Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 300 Series Bedienungsanleitung

Extron electronics

Extron electronics FOX Matrix 320x Bedienungsanleitung

Extron electronics

Extron electronics CrossPoint 450 Plus 64 Series Bedienungsanleitung

Extron electronics

Extron electronics DMS 1600 Bedienungsanleitung

Extron electronics

Extron electronics MVX VGA A Bedienungsanleitung

Extron electronics

Extron electronics XTP II CrossPoint 1600 Bedienungsanleitung

Extron electronics

Extron electronics MAV 62 Bedienungsanleitung

Extron electronics

Extron electronics MPX 423 A Bedienungsanleitung

Extron electronics

Extron electronics HDXP Plus Series Bedienungsanleitung

Extron electronics

Extron electronics DTP CrossPoint 108 4K Bedienungsanleitung

Extron electronics

Extron electronics ISM 482 Bedienungsanleitung

Extron electronics

Extron electronics DTP CrossPoint 84 IPCP Betriebsanleitung

Extron electronics

Extron electronics CrossPoint 300 84 Bedienungsanleitung

Extron electronics

Extron electronics MultiMatrix SMX System Bedienungsanleitung

Extron electronics

Extron electronics DXP 1616 HD 4K PLUS Series Bedienungsanleitung

Extron electronics

Extron electronics HDXP Plus Series Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte