Extron electronics PowerCage FOX SR HDMI Bedienungsanleitung

PowerCage FOX SR HDMI • Setup Guide

This guide provides quick start instructions for an experienced installer to set up and operate the

Extron PowerCage FOX SR HDMI scaling ber optic receiver.

CLASS 1 LASER PRODUCT, see the PowerCage FOX SR HDMI User Guide at

www.extron.com.

CAUTION:

•These units output continuous invisible light, which may be harmful

to the eyes; use with caution. For additional safety, plug the attached

dust caps into the optical transceivers when the ber optic cable is

unplugged.

•Ces produits émettent une lumière invisible continue, qui peut être

dangereuse pour les yeux ; à utiliser avec précaution. Pour une

sécurité renforcée, associez les bouchons anti-poussière à l’ensemble

émetteur/récepteur optique lorsque le câble bre optique est

débranché.

Installation

Step 1 — Mounting

Install the receiver into a PowerCage enclosure as required.

NOTES: •PowerCage boards are hot-swappable.

•Ensure the boards are ush with the rear of the enclosure and the screws are tightened securely before applying power.

Step 2 — Throughput Connections

NOTE: See the two ber cable connection drawings below. You can connect the transmitter and one or more receivers in one of three

ways:

• One way (transmitter to receiver) only, perform step 2a.

• Two way (transmitter to receiver and return), perform steps 2a and 2b.

• One way (transmitter to receiver) with daisy chain (receiver to receiver), perform steps 2a and 2c.

a. Connect the ber between the Tx port on the transmitter and the Rx port on the receiver.

b. If you want the receiver to send return serial data (such as responses from a controlled device) to the transmitter,

connect a cable between the Tx port on the receiver and Rx port on the transmitter.

c. If you want a receiver to daisy-chain the optical signal to another

receiver (up to 10 receivers in a daisy chain):

• Connect the receiver Tx ber cable to Rx on another receiver.

• Set each receiver to daisy chain mode. See “Return Link and

Daisy Chain Modes,” on the next page.

Tx Link and Rx Link LEDs — When lit, the link is active (light is

output [Tx LED] or received [Rx LED]).

NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.

5AMAX.

100-240V 50/60Hz

16 available single board slots or

8 double board slots

Power

Supply

Scre

Receiver

ransmitter

Tx Rx

and

From Transmitter

or Daisy-Chained

Receiver

Tx Rx

Step 3 — Output Connections

HDMI

a. Connect an HDMI video display to the HDMI Output connector.

NOTE: Use a LockIt Lacing Bracket to securely fasten an HDMI cable to the receiver as follows.

1. Plug the HDMI cable into the panel connection

2. Loosen the HDMI connection mounting screw from the panel enough to allow

the LockIt lacing bracket to be placed over it. The screw does not have to be

removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector,

then tighten the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connector mounting screw. The shield it

fastens to is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage

auquel elle est attachée est très fin et peut facilement être dénudé

4. Loosely place the included tie wrap around the HDMI connector and the LockIt

lacing bracket as shown.

5. While holding the connector securely against the lacing bracket, use pliers or similar tools to tighten the tie wrap, then

remove any excess length.

b. Connect a balanced or unbalanced audio device to the Output

Audio captive screw connector, as shown at right.

ATTENTION:

• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. NE PAS connecter les manchons aux

contacts négatifs (–).

c. If you want the PowerCage FOX SR HDMI to pass serial data or control signals, such as for serial control of a projector,

RS-232

VER FIBER

Tx Rx

connect the primary device to the transmitter and the secondary device to the receiver via the left three poles (Tx, Rx, and

_) of the RS-232 Over Fiber 5-pole captive screw connectors on both units.

d. For serial control of the receiver, connect a host device, such as a computer, to the Remote RS-232 port via the left poles

1 2

REMOTE

RS-232

Tx Rx

ALARM

(Tx, Rx, and _) of the Remote RS-232/Alarm 5-pole captive screw connector. The protocol for these ports is as follows:

• RS-232 •9600 baud •no parity

•8 data bits •1 stop bit •no ow control

e. For remote monitoring of the status of the Rx optical link, connect a locally constructed or obtained device to the two right

1 2

REMOTE

RS-232

Tx Rx

ALARM

Alarm poles of the Remote RS-232/Alarm 5-pole captive screw connector. The unit shorts both poles together when no

light is detected.

Step 4 — PowerCage Conﬁguration Port

If desired, for serial control of the transmitter and receiver, connect a host device to the PowerCage enclosure Conguration connector via

the 9-pin D to 2.5 mm mini jack TRS RS-232 cable (included with the PowerCage enclosure or available separately using part number 70-

335-01). Repeatedly press the Comm Select button until the Comm LED lights for the slot where the transmitter or receiver is installed. The

protocol for this port is as follows:

• 9600 baud •no parity •8 data bits

• 1 stop bit •no ow control

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

NO GROUND HERE

Tip

Sleeves

Tip

Ring

Tip

Ring

PowerCage FOX SR HDMI • Setup Guide (Continued)

Operation

After all receivers, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are

encountered, verify that the cables are routed and connected properly and that all display devices have identical resolutions and refresh

rates. If problems persist, call the Extron S3 Sales and Technical Support Hotline at the number that is closest to you.

Return Link and Daisy Chain Modes

The receiver operates in one of two modes (or both modes can be disabled):

Return link mode — The receiver outputs data on its Tx connector for return to the transmitter.

Daisy chain mode — The receiver daisy-chains its Rx connector input through to its Tx connector output.

Issue the following SIS commands from a PC connected to the receiver Remote RS-232 port to toggle between return link and daisy chain

modes or to disable both modes:

66*0*n#, where n= 0= disable, 1= enable return link (default mode), and 2= daisy chain enable

NOTES: •Up to 10 receivers, each in daisy chain mode, can be connected in a daisy chain to a single transmitter.

•Daisy chain mode works with non-HDCP sources only.

HDMI Audio Switch

AUDIO

OFF

This switch mutes (Off position) and unmutes (On position) the embedded audio output on the HDMI output connector.

The audio on the captive screw output always remains active regardless of the setting of this switch.

Indications

Video LED — This LED lights when the receiver detects a signal on its video input.

HDCP

AUDIO

VIDEO

HDCP LED — This LED lights when the video signal is HDCP encrypted.

Audio LED — This LED lights when the receiver detects a low level audio signal for a short period of time.

68-2014-50

Rev B 12 20

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

http://www.extron.com/68-290-01 on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

PowerCage FOX SR HDMI • Setup Guide (Continued)

Andere Handbücher für PowerCage FOX SR HDMI

Inhaltsverzeichnis

Andere Extron electronics Empfänger Handbücher

Extron electronics

Extron electronics FOX3 T 301 Bedienungsanleitung

Extron electronics

Extron electronics FOX3 SR 301 Bedienungsanleitung

Extron electronics

Extron electronics MTP C7 T 15HD RS Bedienungsanleitung

Extron electronics

Extron electronics XTP R HDMI Bedienungsanleitung

Extron electronics

Extron electronics XTP SR HDMI Bedienungsanleitung

Extron electronics

Extron electronics XTP FT HD 4K Bedienungsanleitung

Extron electronics

Extron electronics XTP SFR HD 4K Bedienungsanleitung

Extron electronics

Extron electronics XTP SR HD 4K Bedienungsanleitung

Extron electronics

Extron electronics MTP/HDMI U R Bedienungsanleitung

Extron electronics

Extron electronics MTP R 15HD RSA D Bedienungsanleitung

Extron electronics

Extron electronics FOX3 T 301 Bedienungsanleitung

Extron electronics

Extron electronics MTP T AV Bedienungsanleitung

Extron electronics

Extron electronics MTP 1500RL 15HD A SEQ Bedienungsanleitung

Extron electronics

Extron electronics DTP2 R 212 Series Bedienungsanleitung

Extron electronics

Extron electronics XTP SR HDMI Bedienungsanleitung

Extron electronics

Extron electronics XTP SR HDMI Bedienungsanleitung

Extron electronics

Extron electronics Dual Link DVI Transmitter and Receiver DVI DL 201... Bedienungsanleitung

Extron electronics

Extron electronics MTP C7 RL 15HD A SEQ Bedienungsanleitung

Extron electronics

Extron electronics XTP SR HDMI Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 211 Bedienungsanleitung

Extron electronics

Extron electronics PowerCage FOX SR HDMI Bedienungsanleitung

Extron electronics

Extron electronics MTP 1500RL 15HD A SEQ Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX Tx HDMI Bedienungsanleitung

Extron electronics

Extron electronics TPT101 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung