Extron electronics MGP 641 xi Series Bedienungsanleitung

MGP 641 xi Series • Setup Guide

The MGP 641 xi Series, consisting of MGP 641 xi and MGP 641 xi SDI, are multi-window video signal processors that display

multiple video sources on a single screen in picture-in-picture or picture-by-picture format. They feature dedicated connectivity

for each of the four windows, fully customizable window layouts, HDCP 1.4 and 2.3 support, logo and background image

support, logo keying, and ultra-high resolution support up to 2560x1600 and 4K at 60 Hz on both inputs and outputs. The

MGP 641 xi Series can be controlled and congured using the front panel controls, Simple Instruction Set™ (SIS™) commands,

the internal web page, and the Videowall Conguration Software (VCS).

Both models have four HDMI inputs, one HDMI background input, one HDMI output, and one buffered DTP3 output. In addition,

the MGP 641 xi SDI model has four 12G-SDI inputs. Each input is dedicated to one window.

The VCS program is available at www.extron.com. For information on using VCS, see the VCS Help File, also available on the

Extron website.

About this Guide

This guide provides instructions for an experienced installer to install and congure the MGP 641 xi Series processors.

In this guide, the terms “MGP 641 xi Series” and “MGP” are used interchangeably to refer to both products in the MGP 641 xi

Series.

For full installation, conguration, and operation details, see the MGP 641 xi Series User Guide, available at www.extron.com.

Rear Panel Features and Connections

100-240V

1.5A MAX

50-60Hz

MGP 641 xi

INPUTS

HDMI

BACKGROUND

INPUT

OUTPUTS (DTP3/XTP/HDBT)AUDIO OUT

REMOTE

OUT

SIG LINK

DTP3

DTP

POWER

900mA

DEVICES

LAN

RESET

Tx Rx G

RS-232

MGP 641 xi

100-240V

1.5A MAX

50-60Hz

INPUTS

HDMI HDMI

HDMI

HDMIHDMIHDMI

BACKGROUND

INPUT

OUTPUTS (DTP3/XTP/HDBT)AUDIO OUT

REMOTE

OUT

SIG LINK

DTP3

DTP

POWER

900mA

DEVICES

LAN

RESET

Tx Rx G

RS-232

1 SDI 2 SDI 3 SDI 4 SDI

MGP 641 xi SDI

AAC power connector EDTP remote power LEDs IEthernet LAN connector

BHDMI inputs FDTP/XTP/HDBT output (output 1B) JANALOG AUDIO OUT connector

CHDMI live BACKGROUND INPUT GUSB device connectors KREMOTE RS-232 connector

D HDMI output (output 1A) HRESET button and LED LSDI inputs

Figure 1. Rear Panels

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

Installation Steps

1. Mount the MGP to a rack using the pre-installed side mounting brackets. The unit has a 1U high, full rack wide enclosure.

Alternatively, attach the four provided rubber feet to the bottom of the MGP and place the unit in the desired location.

2. Connect HDMI (or DVI with an appropriate adapter) sources to the HDMI input connectors (inputs 1 through 4) (see figure1,

B on the previous page).

MGP 641 xi SDI only: Connect SDI sources to the 12G-SDI input connectors (L) (optional).

3. If desired, connect a source to the HDMI live BACKGROUND INPUT connector (C). The MGP 641 windows are displayed in

front of this unscaled background video source.

NOTE: You must set the output resolution to match that of the background source, or the background video is not

displayed. The refresh rates do not need to match.

4. Make the following output connections as needed:

zConnect an HDMI (or DVI with an appropriate adapter) display to the HDMI output 1A connector (D).

zConnect a DTP endpoint, XTP matrix switcher, or HDBaseT compatible receiver to the buffered DTP/XTP/HDBT output

connector 1B (F). For cable wiring and recommendations, see the MGP 641 User Guide.

NOTE: RS-232 data can be inserted via Ethernet (see the MGP 641 User Guide or the VCS Help File).

5. Connect a balanced or unbalanced analog audio output device (such as a DSP device or an amplifier) to the 5-pole captive

screw AUDIO OUT connector (J) for 2-Ch audio from the selected input. This connector is configurable via VCS or SIS as

two discrete mono outputs or as one stereo output (see “Audio Wiring” for details).

6. If the MGP 641 is connected to a computer or to a host controller for remote control, do one of the following:

zConnect an RS-232 cable from the host serial port to the Tx, Rx, and G pins (the remaining two pins are not used) of the

5-pole Remote RS-232 rear panel connector (K). The default protocol for the RS-232 port is 9600 baud, 1 stop bit, no

parity, and 8 data bits, with no flow control.

zConnect a USB-A to USB-C cable from the host USB-A port to the MGP 641 front panel USB-C CONFIG port (see

figure3, Aon the next page).

zConnect an RJ-45 network cable from the host Ethernet port to the MGP 641 rear panel LAN port.

7. (Optional) Connect USB devices such as USB touch panels, keyboards, mice, or flash drives to one or both USB-A 3.0

Devices ports for use with the annotation function (LinkLicense required), and to save images (see figure1, G).

8. Connect power to the MGP by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz power

source into the AC power connector (A).

9. Apply power to all connected devices.

Audio Wiring

Wire the audio output connectors as shown in gure2. Use the supplied tie wrap to strap the audio cable to the extended tail of

the connector.

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Do not tin the wires

Figure 2. Wiring the Audio Output Connectors

ATTENTION:

• For unbalanced outputs, do not connect wires to the “-” poles.

• Pour les sorties asymétriques, ne connectez pas de câbles aux pôles «-» .

NOTE: The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).

MGP 641 xi Series • Setup Guide (Continued)

Front Panel Controls

The MGP 641 xi Series front panel buttons, ADJUST knobs, and the LCD screen menus provide navigation of general settings

required to initially control and congure the MGP. When you press a button or rotate a knob, the LCD screen displays the

available settings.

MGP 641 xi

MULTI-GRAPHIC PROCESSOR

CONFIG

WINDOW SELECT

MUTE

FREEZE

PRESET

RECALL

/SAVE

ENTER

WINDOW

/IMAGE

SIZE

WINDOW

/IMAGE

POSITION

WINDOW

/IMAGE

ZOOM

AUTO

IMAGE

2 3 4

ADJUST

BB CC DD EE FF GG HH

AUSB CONFIG port EPicture control buttons

BWindow and input selection buttons FLCD screen

CMUTE and FREEZE buttons GMenu navigation buttons

DPRESET RECALL/SAVE and ENTER buttons HHorizontal and vertical ADJUST knobs

Figure 3. MGP 641 xi Series Front Panel

AUSB CONFIG port — Connect a host device to this USB-C port for device configuration, control, file transfer, and firmware

upgrades.

BWindow selection buttons — Press these buttons to select windows (inputs) 1 through 4 for configuration. The selected

button lights orange.

CMUTE and FREEZE buttons —

zMUTE — Press this button to mute the selected window. The button lights orange when the mute is enabled. To unmute,

press the lit MUTE button again.

zFREEZE — Press this button to freeze the selected window. The button lights orange when freeze is enabled. To unfreeze

the window, press the lit FREEZE button again.

DPRESET RECALL/SAVE and ENTER buttons — In combination, these buttons save the current settings to a window

preset or recall a stored preset (up to 128). See Saving and Recalling Presets on page4 for more information on using

these buttons.

EPicture control buttons — Press these buttons to adjust the size, position, and zoom, or to perform an auto-image

adjustment on the selected window.

zPress WINDOW/IMAGE SIZE, WINDOW/IMAGE POSITION, or WINDOW/IMAGE ZOOM once to select the window (the button

lights orange) or twice to select the image within the window (the button lights green).

Use the horizontal ([) and vertical ({) ADJUST knobs to adjust the settings shown on the left and right sides of the LCD

screen, respectively.

zPress AUTO IMAGE to perform an auto image adjustment on the selected input window. Press it again to confirm the

adjustment.

FLCD screen — Displays the configuration menus, messages, and your selections.

GMenu navigation buttons — Press MENU to step through the menus on the LCD screen. From each menu, press NEXT to

step through its submenus.

HHorizontal and vertical ADJUST knobs — Turn these knobs to step through submenu options and preset slots, and to

adjust picture controls.

Setting Up the MGP 641 xi Series Using the Front Panel

After installing and connecting the MGP, use the front panel controls to congure and

adjust the unit for use. Press the MENU button to access the Main Menu (shown at right).

Then, repeatedly press the MENU button to cycle through the menus and access the Input

Conguration, Output Conguration, and Advanced Conguration menus to perform

steps 1 through 4.

1. Use the Input Conguration menu to configure inputs 1 through 4, including EDID

selection, aspect ratio selection, HDCP authorization, input format (SDI xi only), and

image rotation (available only for inputs 2 and 4). Some of these settings may require

about 3 seconds to take effect after selection.

2. Use the Output Conguration menu to configure the outputs, including signal type,

resolution and rate, HDCP Note (encryption notification), TP and HDMI format, and

display rotation.

3. From the Advanced Conguration menu, Test Pattern submenu, use the crop and

grayscale test patterns to adjust the display settings.

4. Use the front panel menu system to set the IP address for the unit:

a. Press the MENU button repeatedly until the View Com Settings menu name is

displayed on the LCD screen.

b. Press and hold the NEXT button until the LCD screen displays Edit Comm

Settings.

c. Press the NEXT button repeatedly until IP Address appears on the LCD screen.

d. Rotate the horizontal ADJUST knob ([) to select a section of the address (octet)

to edit, and the vertical ADJUST knob ({) to increase or decrease the selected

number.

e. Repeat step d for the remaining octets.

5. Use the picture control buttons to size and position each window as desired for your

application.

6. Save each window configuration to any of the 128 window preset slots for easy recall

of window settings.

Saving and Recalling Presets

To save the current conguration as a preset:

1. Press and hold the PRESET RECALL/SAVE button until the LCD screen displays

Window Preset/Save to #nnn (approximately 2 seconds). The button lights orange.

2. Rotate either ADJUST knob to select the preset number or name to which you want to

save this configuration.

3. Press the ENTER button. The button lights orange. Both the PRESET RECALL/SAVE and

the ENTER buttons remain lit until the preset is saved, then turn off.

To recall a saved preset, press the PRESET RECALL/SAVE button and

immediately release it. The button lights orange, and the LCD window displays

Window Preset/Recall #nnn. Rotate either ADJUST knob to select a preset number,

then press ENTER. The ENTER button lights orange and remains lit until the window preset

is recalled, then both buttons turn off. The LCD window displays WINDOW PRESET #nnn

Saved.

Power

Output

Configuration

30 sec.

Image/Logo

Configuration

30 sec.

Default

Cycle

Advanced

Configuration

Exit Menu

Press NEXT

30 sec.

View Comm

Settings

30 sec.

Input

Configuration 30 sec.

30 sec.

Window

Configuration

Hold 5 sec.

Edit Comm

Settings 30 sec.

2 sec.

Extron

MGP 641 xi [SDI]

60-1574-1n

FW n.nn.nnnn

30 sec.

2 sec.

MGP 641 xi Series • Setup Guide (Continued)

SIS Commands

As an alternative to the front panel controls, you can issue SIS commands via RS-232, USB, or Ethernet from the host to set up

and control the MGP 641 (see the MGP 641 xi Series User Guide at www.extron.com for a complete list of SIS commands).

Command ASCII Response Additional Description

Input Video Type

Set video type X!*X#\ ItypX!*X#] Set input X! to format X#.

View video type X!\ ItypX#] View video type X# set for input X! .

View detected format X!*\ ItypX!*X1*] View actual video format X1* on input X!.

Window and Preset

Mute (blank) a window X!*1B VmtX!*1]Blank (mute) window X!.

Unmute a window X!*0B VmtX!*0]Unmute window X!.

Save window preset 1*X1$,1Spr*X1$] Save current window settings as preset X1$.

Recall window preset 1*X1$.1Rpr*X1$] Recall window preset X1$.

Audio

Audio input switch X!$ InX!•Aud]Select (switch) the audio from input X!.

Global audio mute X$Z AmtX$] Set mute state of all audio outputs to X$.

Discrete audio mute X@*X$Z AmtX@*X$] Set mute state of audio output X@ to X$.

View global mute status ZX$•X$•X$] View audio mute status:

HDMI, DTP, analog audio

View discrete audio mute X@*Z X$] View mute status X$ of audio output X@.

Front Panel Lock Mode

Set front panel lock mode X3%X ExeX3%] Set front panel lock mode to X3%.

Read front panel lock mode XX3%] View front panel lock mode X3%.

IP Setup

Set IP address EX10& CI}Ipi•X10&] Set unit IP address X10&.

Read IP address ECI} X10&] View the unit IP address (X10&).

Set subnet mask EX11# CS}Ips•X11#] Set unit subnet mask X11#.

Read subnet mask ECS} X11#] View the unit subnet mask (X11#).

Set gateway address EX10& CG}Ipg•X10&] Set IP address X10& for your gateway.

Read gateway address ECG} X10&] View the gateway IP address for the unit.

Set DHCP mode EX1)DH}IdhX1)] Enable or disable DHCP.

View DHCP mode EDH} X1)] View the DHCP setting.

Reboot networking E2Boot}Boot2]Restart the network after IP setting changes.

KEY:

X! = Input (window) number 1- 4. 0= all windows (mute and freeze only)

X@ = Output number 1= HDMI output, 2= TP output, 3= Analog audio output, 99 = All outputs

X# = Input video type 1= HDMI/DVI, 2= SDI (auto detect)

X$ = Mute status 0= unmuted, 1 = muted

X1) = DHCP on or off status 0= off or disabled, 1= on or enabled

X1$ = Window preset number 1-128

X1* = Detected input format 0=no signal, 1= HDMI, 2= DVI, 3= SDI, 4= HD-SDI, 5= 3G-SDI,

6= 6G-SDI, 7= 12G-SDI, 8= Unknown

3through 8apply to MGP 641 xi SDI only.

X3% = Front panel lock (executive) mode 0= Off (front panel unlocked, default), 1= Complete front panel lockout

2= Only window preset recall, mute, freeze, and auto image are available.

X10& = IP or gateway address nnn.nnn.nnn.nnn. Leading zeros are optional in each octet.

X11# = Subnet mask nnn.nnn.nnn.nnn. Leading zeros are optional in each octet.

NOTE: IP and subnet commands require an ESC 2BOOT command before any changes are applied (see the Reboot

Networking command, above).

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

68-2396-51

Rev. A 06 23

Andere Handbücher für MGP 641 xi Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Schalten Handbücher

Extron electronics

Extron electronics USB HUB4 Series Bedienungsanleitung

Extron electronics

Extron electronics VSW 2VGA A Bedienungsanleitung

Extron electronics

Extron electronics YCS SW2 A Bedienungsanleitung

Extron electronics

Extron electronics System 5 IP Series Bedienungsanleitung

Extron electronics

Extron electronics System 5 IP Series Bedienungsanleitung

Extron electronics

Extron electronics ISM 824 Bedienungsanleitung

Extron electronics

Extron electronics Extron MediaLink MLS 304MA Bedienungsanleitung

Extron electronics

Extron electronics System 4LD xi Bedienungsanleitung

Extron electronics

Extron electronics SVS 100 Bedienungsanleitung

Extron electronics

Extron electronics MPS 409 Bedienungsanleitung

Extron electronics

Extron electronics SW2 VGAxi Bedienungsanleitung

Extron electronics

Extron electronics SW HDMI Series Bedienungsanleitung

Extron electronics

Extron electronics 4xi series Bedienungsanleitung

Extron electronics

Extron electronics YCS SW6 MX Bedienungsanleitung

Extron electronics

Extron electronics PVS 405D Bedienungsanleitung

Extron electronics

Extron electronics SW8/12 VGA Ars Bedienungsanleitung

Extron electronics

Extron electronics SW4 12G HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics MPS 112 Bedienungsanleitung

Extron electronics

Extron electronics UCS 303 Bedienungsanleitung

Extron electronics

Extron electronics Extron SW 2 VGAcc Bedienungsanleitung

Extron electronics

Extron electronics PVS 405D Bedienungsanleitung

Extron electronics

Extron electronics YCS SW2 A Bedienungsanleitung

Extron electronics

Extron electronics PVS 305SA Bedienungsanleitung

Extron electronics

Extron electronics SW2 USB Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung