Extron electronics TLP Pro 720C Bedienungsanleitung

Product Category

TLP Pro 720C • Setup Guide

Overview

The Extron TLP Pro 720C is a 7 inch Cable Cubby touchpanel with a ip-up, 800x480 LCD touchscreen with 18-bit color depth.

It is ideal for any AV application requiring a full-size, Cable Cubby touchpanel with a customizable interface. This guide provides

instructions for experienced installers to mount and install a TLPPro 720C touchpanel. For more complete instructions, see the

TLPPro 720C User Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

Global Configurator Professional or Global Configurator Plus — for setting up and conguring the control processor and

touchpanel.

GUI Designer — for designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

Both software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you will also require

IP address Subnet mask Gateway

User name — by default these are either admin or user.

Passwords — by default these are either extron (for admin) or the eld is left blank (for user).

Make a note of the touchpanel MAC address.

Make sure you are familiar with all the included parts and have all the necessary tools (see page 2) for installing the cable

cubby.

Included Parts

With Power

Module

Without Power

Module

AC Power Module* 1 0

Pass-through AAPs†3 3

Blank AAPs 6 6

1-position bracket kit 0 1

2-position bracket kit 3 4

3-position bracket kit 1 1

NOTES:

* Inside the US, the TLP Pro 720C can be purchased with or without an AC power module. Outside the US, see

www.extron.com to nd an AC power module for your country.

† Active or Passive AAPs must be purchased separately (see www.extron.com).

TLP Pro 720C

Table Clamps

AC Power Module*

Blank AAPs

Pass-thru AAPs

Extron

Removal Tool

Zip Ties #4−40 Screws

and Nuts

2 Pos

AAP Shelf Bracket Kits

(2 brackets/kit)

3 Pos1 Pos

TLP Pro 720C • Setup Guide (Continued)

Tools Required for Installation

Safety Glasses

Phillips Screw Driver

Tape Measure

1/4" Hex Nut Driver

Marking Pen

Square

Vacuum Cleaner

Mount and Cable All Devices

ATTENTION: Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply

section of the TLP Pro 720C User Guide or the IPL Pro User Guide.

ATTENTION: Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section

«sources d’alimentation» du TLP Pro 720C UserGuide ou du IPLProUserGuide.

Mount the units (see Mounting below).

Install power modules in the cable cubby.

Install AAPs and run cables to the cable cubby.

Connect cables to the touchpanels.

Connect the power cords and power on all devices.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and the touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see page 8) or the Toolbelt feature of Global Congurator Professional or Global Congurator Plus to

set the DHCP status and, if necessary, the IP address, subnet mask, gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

The Global Conﬁgurator Professional Help File, the Global Conﬁgurator Plus Help File, and the GUI Designer Help File provide

step-by-step instructions and more detailed information. The Global Congurator Professional and Global Congurator Plus help

les include an introduction to the software and sections on how to start a project and conguration.

Mounting

Planning

Before making any cuts, select the best location for the TLPPro 720C.

Ensure that the edge that opens on the lid is oriented correctly.

Ensure there is enough space for all the system cables and components, including cable retractors, if they are to be installed.

Decide on the method for cutting a hole in the table:

zHand router and template

zCNC wood router

zJigsaw and paper template

Verify that you have the correct template or dimensions.

Check all relevant regulations.

zEnsure that the installation complies with local, state, and national building and electrical codes.

zEnsure that the installation complies with the Americans with Disabilities Act or other accessibility requirements.

Product Category

Step 1 — Obtain Cut-out Dimensions

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise care

to prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et qualiés.

Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

• Use the appropriate metal Extron routing template or refer to the surface cutout dimensions before cutting a hole in

the furniture or other surface. Pay special attention to the direction the unit will face. The connector access side is

underlined. Extron is not responsible for miscut mounting holes.

• Utilisez le gabarit de détourage métallique approprié ou reportez-vous aux dimensions de découpe de la surface

indiquées ci-après avant de découper le meuble ou la surface. Faites particulièrement attention à la directions dans

laquelle l’unité sera dirigée. Le côté pour accéder au connecteurs est souligné. Extron ne sera pas responsable des

erreurs de coupe.

• Ensure the table surface is at least 0.375 inches (0.95 cm) thick.

• Assurez vous que la surface de la table est au moins 0,95 cm (0,375") d’épaisseur.

If using a hand router, you should purchase the Extron TLP Pro 720C routing template.

If using a CNC wood router, use the exact cut-out dimensions (see Using a CNC wood cutter below).

If using a reciprocating saw or jigsaw use the paper cut-out template (available under the Downloads tab on the TLP Pro 720C

page at www.extron.com).

Step 2 — Cut the Surface

CAUTION: Risk of personal injury: Wear safety glasses when operating power equipment.

ATTENTION: Risque de blessure: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique.

Be certain the cut is laid out in exactly the desired location and the edge that opens on the lid is correctly oriented. After verifying

and checking dimensions, cut a hole in the surface of the furniture where the enclosure will be installed (see “Preparing the Table”

in the TLP Pro 720C User Guide). There are three methods for cutting the hole in the table:

Using a hand router

Recommended method — Use the Extron TLP Pro 720C

routing template. Refer to the Routing Template User Guide,

available at www.extron.com, to prepare the template and

use the template to cut the hole.

NOTE: The metal router guide must be purchased

separately. It is reusable and should not be discarded

when the installation is complete.

Using a CNC wood cutter

Recommended method — Use the exact cut-out dimensions:

8.90 +0.00/-0.02 inches W x 7.10 +0.00/-0.02 inches D

(22.61 +0.00/-0.05 cm W x 18.03 +0.00/-0.05 cm D)

NOTE: The underlined dimension is the connector or AAP

access side for the unit.

Using a reciprocating saw or jigsaw

Acceptable method — Use the paper cut-out template (available

under the Downloads tab on the TLPPro 720C page at

www.extron.com).

HSA 200

USER ACCESS

HSA 200

CABLE CUBBY 300

USER ACCESS

Cut-Out Template for the Extron

TLP Pro 720C

Outer Edge of Trim Ring

(Do not cut this line.)

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray)from the template.

3. Mark the position on the wall or

furniture where theTLP 710MV

is being installed.

4. Cut the opening.

P/N 68-2046-01 Rev. B

Page size: 11" x 17"

Print scale 1:1

Do not shrink.

P/N

TLP Pro 720C • Setup Guide (Continued)

Step 3 — Run all Cables

Run all cables necessary to support the AC connector, the cables stored in the cubby, and all planned AAP connectors. Run the

cables below the table and through the hole that was cut in Step 2. Leave enough slack in the cables to connect or route them

before the cubby is installed in the table. Leave enough space under the enclosure for the external power supply and connection

of AV cables and the network connection for the TLPPro 720C.

Step 4 — Install Cable Retractors (Optional)

If required, Extron cable retractors should be installed in the enclosure at this stage. For complete information about retractors

and how to install them, see the Retractors User Guide, which is available from the Extron website (www.extron.com).

Step 5 — Install Power Module (Optional)

ATTENTION:

•For units that are used in North America, only

use AC power modules that are UL Listed Model

“Cable Cubby AC Power Module”.

•

•The unit is not UL Listed if it uses any AC power

module other than Model “Cable Cubby AC Power

Module”.

•

NOTE: For models that do not include a power module,

see the Extron website to select a power module that is

suitable for your location.

The power module takes up two or three AAP spaces, depending on

the model, and may be installed before or after the AAP assembly is installed. It may be installed with AAPs on either side.

1. Secure the power module into position with #4-40 Phillips head screws and star washers.

CAUTION: Risk of electric shock: To ensure proper electrical grounding, use the provided grounding screws and star

washers.

ATTENTION: Risque de choc électrique: An d’assurer une mise à la terre correcte, utilisez les xations de mise à la

terre et les rondelles en étoile fournies.

2. Run the cable or conduit to a convenient junction box. Extron recommends the circuit be attached to a junction box that is

directly wired to the main circuit.

Step 6 — AAP Assembly

Install all desired cables into the cable pass-through AAPs and

install the AAPs into the cable cubby.

The simplest way to install the cables and AAPs is to populate

the AAP brackets outside the cubby and then install the

populated AAP shelf assembly into the cubby.

Install cables in the pass-through holes as shown in the gure

to the right.

TIP: Hand tightening the #4-40 nuts makes it easier to

place and secure the assembly inside the enclosure.

NOTE: An extra column of AAP bracket mounting points is

available for use with TLP Single-space AAP mounting

brackets. Single-space brackets will not t in any other

location.

Rear Bracke

Front Brackets

Secure the po

wer module

to the

TLP Pro 720C frame

with #4-40 Phillips head

scre

ws and star washers.

Extron

The extra column

of mounting points

is for installing

single-space

AAP brackets.

Product Category

Step 7 — Install the AAP Assembly

1. From under the table, push the rst AAP assembly

through the bottom of the enclosure. The holes in the

rear bracket must align with the bottom row of holes on

the rear face of the enclosure.

TIP: Ensure there is enough space above the AAP

assembly for the lid to close completely without

cables or connectors contacting the touchpanel.

2. Secure the AAP assembly into position with the

provided Phillips head screws.

3. Tighten the nuts that secure the AAPs to the brackets.

COMPUTER

AUDIO

Phillips Head Scre

(secure AAP

assemb

ly)

Tighten down

AAP nuts.

Push assemb

ly through

bottom of enclosure.

Large slot

provides tool

access to fasten

rear brackets.

Extron

Step 8 — Mounting the Enclosure

Mount the cable cubby enclosure in the table.

CAUTION: The anged edges of the top of the surface enclosure are sharp. These edges are also soft and may be easily

nicked or bent. Exercise caution when handling the enclosure to prevent personal injury or damage to the enclosure.

ATTENTION: Les extrémités à brides du haut de la surface du boîtier sont aiguisées. Ces extrémités sont aussi lisses

et peuvent facilement être coupées ou pliées. Soyez prudents lorsque vous manipulez le boîtier an d’éviter de

l’endommager ou de vous blesser.

1. Remove the edge grommet protecting the edges of the trim ring

and the plastic lm on the nished surfaces.

ATTENTION: Do not use isopropyl alcohol or other solvents

to clean the Cable Cubby. Strong solvents will ruin some

nishes.

ATTENTION: Ne pas utiliser de l’alcool isoproprylique ou

d’autres solvants pour nettoyer le CableCubby. Les solvants

forts endommageront certaines nitions.

2. Carefully lower the enclosure into the hole cut in the table (see

Step2 — Cut the Surface on page 3). Ensure the trimring(5)

is ush with the top of the table.

3. Under the table, attach the table clamps (3) to the pins on

each side of the enclosure. It may be necessary to loosen the

wingnuts (1) and the Phillips head screws (2).

4. When the clamps are properly seated on the pins, tighten the

Phillips head screws until the clamp faces (4) are tightly secured against the bottom of the table.

5. To prevent the screws from becoming loose, secure the wingnuts against the table clamp bodies.

TLP Pro 720C • Setup Guide (Continued)

Connecting the TLP Pro 720C

The cable connections are located in a panel on the bottom of the TLP Pro 720C:

APower connector — Connect a 12 VDC, 1.0 A power supply (not provided) to this 2-pole, 3.5 mm captive screw connector.

ATTENTION: The TLP Pro 720C can use a 12 VDC desktop power supply and is also Power over Ethernet (PoE

802.3af, class3) compliant. Do not connect either power supply before reading the Attention in the Power Supply

section of the TLPPro720C User Guide.

ATTENTION: Le TLP Pro 720C peut utiliser une source d’alimentation externe 12 Vcc, et est également compatible

avec l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas de sources d’alimentation externes

avant d’avoir lu les mises en garde dans la section «PowerSupply» du TLPPro720C User Guide.

NOTES:

• The TLP Pro 720C ships without a power supply. Either the 12 VDC power supply or the PoE injector must be

purchased separately.

• If a 12 VDC and a PoE power supply are both connected to the TLP Pro 720C, the PoE injector takes precedence.

If a PoE power loss is detected, the touchpanel switches seamlessly to the 12 VDC supply without needing a

system reboot.

BNetwork and Power over Ethernet (PoE) Connector — Connect the touchpanel to the LAN using a twisted pair cable,

terminated with an RJ-45 connector. The connector can also be used with a PoE power injector (not provided).

An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

Product Category

Front Panel Features

To see all the front panel features, remove the bezel, using the Extron Removal Tool. For a complete description of all these

features and their function, see the TLP Pro 720C User Guide.

AAmbient light sensor — monitors ambient light level and adjusts screen brightness, based on the settings congured using

the setup menu (see page 8).

BBezel attachment point — The TLP Pro 720C has eight attachment points (two on each side, two on the top edge, and two

on the bottom edge).

CLCD screen — the TLP Pro 720C has a 7 inch screen with a 800x480 resolution

DReset LED— indicates power status and reset status of the device.

ECommunication LED — shows the conguration and connection status of the touchpanel:

zUnlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).

zBlinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.

zPermanently lit if the touchpanel has not been congured and is not connected to an IP Link Pro control processor.

The indicator can be toggled between enabled and disabled, using the setup menu (see page 8).

FReset button — this button allows the unit to be reset. The TLP Pro 720C has three reset modes that are initiated by

pressing the reset button. For full information about these different modes, see the TLPPro 720C User Guide.

GMenu button — activates the setup menu and calibration screen (see page8).

HBezel — use the included removal tool to detach the bezel.

ISpeaker — one, placed inside the cable cubby, provides audible feedback for

the user.

JBezel removal slots — allow removal of bezel, using Extron removal tool.

KIllumination LED — provides light for cable cubby enclosure.

68-2406-50 Rev. A

04 14

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

TLP Pro 720C • Setup Guide (Continued)

Setup Menu

The setup menu opens when the menu button is pressed (see Front

Panel Features, Gon page 7). There are ve different screens: Status,

(shown in the gure to the right) Network, Display, Audio, and Advanced.

The screens can be selected by pressing the appropriate button in the

navigation bar at the top of the screen (for more information, see the

TLPPro 720C User Guide).

Press the menu button for at least 2 seconds to open the calibration

screen. Follow the on-screen instructions.

Status DisplayAudioAdvanced Exit

Network

Info

Model: TLP Pro 720C

Part Number: 60-1396-020A

Firmware

Version: 1.00

PoE Status:On

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

Project:

Sleep Timer:

800x480

N/A

5 Minutes

Audio

Master Volume:

Master Mute:Off

Advanced

Controller IP:N/A

Project Size:N/A

Inhaltsverzeichnis

Andere Extron electronics Touchscreen Handbücher

Extron electronics

Extron electronics TLP Pro 1725TG Bedienungsanleitung

Extron electronics

Extron electronics TouchLink Series Gebrauchsanweisung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP 700TV Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP Pro 725C Series Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1220MG Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP Pro 1020 Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP Pro 1025T Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225MG Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 350CV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225MG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 710CV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1520TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1220TG Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung