Extron electronics TLP Pro 720M Bedienungsanleitung

Product Category

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions befor

e connecting the

oduct to the power sou

rce.

TLP Pro 520M and TLC Pro 521M • Setup Guide

Overview

The Extron TLP Pro 520M and TLC Pro 521M are 5 inch wall mounted touchpanels with 800x480 capacitive glass touchscreen.

The Extron TLC Pro 521M also features a built-in controller in a compact form factor. They are ideal for any AV application requiring

compact touchpanels with exible mounting options and a fully customizable interface. This guide provides instructions for

experienced installers to mount and install these touchpanels. For complete instructions, see the TLPPro 520M and TLCPro 521M

User Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

GUI Designer — for designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

Global Configurator®Plus and Professional — for setting up and conguring the control processor and touchpanel.

Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings,

system utilities, and user management for TouchLink Pro devices.

All three software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you will also require

IP address Subnet mask Gateway

User name — this can be either admin or user.

Password — by default this is extron (for either admin or user).

Make a note of the touchpanel MAC address (see the rear panel label).

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section

of the TLP Pro 520M and TLCPro 521M User Guide or the IPL Pro User Guide.

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources

d’alimentation» du TLP Pro 520M and TLCPro 521M UserGuide ou du IPLProUserGuide.

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on the following page).

Connect cables to the touchpanel.

Connect the power cords and power on all devices.

Set Up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor (for the TLP Pro 520M), and the touchpanel to the same

Ethernet subnetwork.

Use the Setup Menu (see page 6) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,

gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

The GUI Designer Help File, Global Conﬁgurator Help File, and the Toolbelt Help File provide step-by-step instructions and more

detailed information. The Global Conﬁgurator Help File includes an introduction to the software and sections on how to start a project

and conguration.

TLP Pro 520M and TLC Pro 521M • Setup Guide (Continued)

Mounting

These touchpanels can be mounted in walls or furniture (see Wall-mounting or Furniture-mounting, below) or with a range of kits

(see Mounting Kits, below).

Wall-mounting or Furniture-mounting

Figure 1 shows the TLP Pro 520M. Mount the TLC Pro 521M in the same way.

Either touchpanel can be mounted directly to the wall or directly into furniture, such as a podium or table, without a kit.

ATTENTION:

• Do not install the TLP Pro 520M or TLC Pro 521M in a re resistant rated wall or partition assembly.

• Ne pas installer le TLP Pro 520M ou le TLC Pro 521M dans un mur résistant au feu ou une cloison.

To mount the touchpanel directly into drywall, follow these steps. The steps are similar if the unit is mounted in furniture.

You will need a marking pen, a wallboard saw or jigsaw, a le or sandpaper, and a Phillips head screwdriver.

1. Use the cut-out template (available from www.extron.com) to mark the wall at a suitable location.

2. Use a wallboard saw or jigsaw to cut away the material within the guidelines drawn in step 1.

3. If there is insulation inside the drywall, remove at least 6inches of the insulation in all directions around the opening.

4. Check the size of the opening by inserting the included wallplate adapter into it.

5. Use a Phillips head screwdriver to tighten the locking arm screws of the wallplate adapter (see gure 1, 5). As the screws

tighten, the locking arms rotate behind the wall and hold the adapter in place.

ATTENTION:

• Do not overtighten the screws as this can damage the catches or the wall.

• Ne serrez pas trop les vis au risque d’endommager les attaches ou le mur.

6. Route cables, leaving enough slack to connect them to the back of the touchpanel.

7. Plug the cables into the rear panel connectors (see Rear Panel Features and

ﬁgure4 on page 4).

zIf required, insert captive screw connectors into the control ports.

zConnect the LAN port to the PoE power injector or

a PoE enabled switch.

zIf you use the LAN port only as a network

connection, connect a 12 VDC, 1.0 A power supply

to the 2-pole captive screw power input connector.

NOTE: Either the power injector or the 12 VDC

power supply must be purchased separately.

Push excess cables into the wall cavity.

8. Press the touchpanel onto the wallplate adapter (8)

until it snaps into place. Four catches, two on each

side, hold the touchpanel in place.

9. Remove the bezel by inserting the provided Extron

pry tool into the notches on the bottom surface of

the bezel (9).

10. Fasten the touchpanel to the wallplate adapter with

the two provided #4-40 x ¼” Phillips head screws

(¢). For extra security, use two security screws

(not provided).

11. Reattach the bezel.

12. If required, perform the initial conguration, using the Setup Menu (see page 6).

Figure 1. Mounting the TLP Pro 520M

TLP Pro 520M snaps

to wallplate adapter

(2 places on each side).

Tighten screws to

rotate locking arms

and secure wallplate

adapter.

TLP Pro 520M

Mounting

Screws (2)

Remove

Bezel.

Mounting Kits

The touchpanels can be mounted in both landscape and portrait orientations. Bezels for mounting in the portrait orientation must be

purchased separately.

Optional mounting kits, which must be purchased separately, are available. Follow the instructions provided with the kit.

zDesktop mounting — SMB 1 (with the optional SMA-1, which must be purchased separately)

zGlass mounting — GMK 1 (requires the SMB 1, which must be purchased separately)

zRack mounting — RM 1

zBack Box wall mounting — BB 1

Product Category

Front Panel Features

The front panel features for both the TLP Pro 520M and TLPPro521M are very similar.

BCD

Figure 2. TLP Pro 520M Front Panel without bezel

To remove bezel, insert

Extron removal tool here.

Figure 3. TLP Pro 520M Bezel

AStatus lights — one on each side can be congured to provide system feedback.

BMotion sensor — detects motion in front of the touchpanel.

CAmbient light sensor — monitors ambient light level and adjusts screen brightness.

DCommunication LED (TLP Pro 520M only) — shows the conguration and connection status of the touchpanel:

zUnlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).

zBlinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.

zPermanently lit red if the touchpanel has not been congured.

ELCD screen — the 5 inch LCD capacitive glass touchscreen has a 800x480 resolution.

FMenu button — activates the setup menu (see page6). There is a slot in the bottom surface of the touchpanel, directly

under the Menu text (see the arrow in gure 2, G).

GSpeaker — one, placed under the screen, provides audible feedback for the user.

TLP Pro 520M and TLC Pro 521M • Setup Guide (Continued)

Rear Panel Features

The TLP Pro 520M and TLC Pro 521M rear panels are identical except for the 3 sets of additional control ports on the TLC Pro 521M.

RS-232 Relay IR/S

Tx Rx G12 CSG

FHG

TLP Pr

o 520M TLC Pro 521M

Figure 4. TLP Pro 520M and TLC Pro 521M rear panels

APower connector ENetwork and Power over Ethernet (PoE) connector

BDigital input monitoring port FRS-232 connector (TLC Pro 521M only)

CReset LED GRelay connector (TLC Pro 521M only)

DReset button HIR/S connector (TLC Pro 521M only)

APower connector — Connect a 12 VDC, 1.0 A power supply (not included) to this 2-pole, 3.5 mm captive

screw connector.

ATTENTION:

• The TLP Pro 520M and TLC Pro 521M can use a 12 VDC desktop power supply and is

also Power over Ethernet (PoE 802.3af, class3) compliant. Do not connect either power

supply before reading the Attention in the Power Supply section of the TLPPro520M and

TLC Pro 521M User Guide.

• Le TLP Pro 520M et le TLC Pro 521M peuvent utiliser une source d’alimentation externe 12 Vcc,

et sont également compatible avec l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne

branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la

section «PowerSupply» du TLPPro520 and TLC Pro 521M User Guide.

NOTE: The touchpanels ship without a power supply. Either the power injector or the 12 VDC power

supply must be purchased separately.

BDigital input monitoring port — this two-pole captive screw port (1 = signal and 2 = ground) monitors digital input

with or without a +5 VDC pull-up.

CReset LED — indicates power status and reset status of the device.

DReset button — reset modes are initiated by pressing this recessed button. There are three reset modes for

the TLP Pro 520M and four reset modes for the TLC Pro 521M. For full information about these different modes, see the

TLPPro 520M and TLCPro521M Series User Guide.

POWER

12V

1.0A MAX

Rear

Panel

RidgedSmooth

INPUT

Product Category

ENetwork and Power over Ethernet (PoE) connector (see

ﬁgure 4)— is on the right side of the recessed area. Connect the

touchpanel to the LAN using a twisted pair cable, terminated with

an RJ-45 connector. The connector can also be used with a PoE

power injector (not provided).

An Extron IP Link Pro control processor must also be connected to

the same network as the TLP Pro 520M.

RJ-45

Connector

Insert Twisted

Pair Wires

Pins: 12345678

Ethernet

Extron Devices

(Switchers, Scalers)

TCP/IP

Network

Crossover Cable

(for direct connection to a PC)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-green

2 orange 2 green

3 white-green 3 white-orange

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 orange

7 white-brown 7 white-brown

8 brown 8 brown

T568B T568A

LAN (Ethernet)

Default protocol, public ports:

• TLC Pro 521M IP address: 192.168.254.252

• TLP Pro 520M IP address: 192.168.254.251

• Gateway IP address: 0.0.0.0

• Subnet mask: 255.255.255.0

• DNS address: 127.0.0.1

• DHCP: off • DNS: 127.0.0.1

ouchpanel

LAN Port

IPL Pro Controller

(TLP Pro 520M only)

FRS-232 connector (TLC Pro 521M only, see ﬁgure 4)— three-pole 3.5 mm captive screw connector supports

software ow control (Pin 1 = Tx, Pin 2 = Rx, Pin 3 = G).

GRelay connector (TLC Pro 521M only, see ﬁgure 4) — three-pole 3.5 mm captive screw connector for normally

open (NO) contact closure (Pin1 = 1, Pin 2 = 2, Pin3 = C).

To Room

Control

Equipment

Normally

Open (2)

Common

Normally

Open (1)

Common

21C

RELAY

Do not exceed a total

of 24V at 1A for each

relay port.

Common

Relay 2

Relay 1

ll relays

normally

open.

Figure 6. TLC Pro 521M Relay Connector

HIR/S connector (TLC Pro 521M only, see ﬁgure 4) — two-pole 3.5 mm captive screw connector can be congured to operate

as an IR or unidirectional serial port (Pin 1 = S, Pin 2 = G).

IR/S

(-)

(+)

(-)

(+)

(-)

the IR Receiver of a

Projector, Display, or

Source Device

Two Single IR Emitters

Ground

IR Output Signal

Unidirectional

IR or RS-232 Output

Ground

To a Projector,

Panel Display, or the

Wired IR Remote or

RS-232 Port of a

Source Device

IR/Serial Ports

Output options:

• IR (30 kHz to 300 kHz,

with or without carrier signals)

• Unidirectional RS-232

Figure 7. TLC Pro 521M IR or Unidirectional Serial Port

Figure 5. Connection to the LAN/PoE Port

RS-232

TxRx G

68-2153-50 Rev. C

02 16

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Status DisplayAudioAdvanced Exit

Network

Info

Model: TLP Pro 520M

Part Number: 60-1185-02

Firmware

Version: 1.00

PoE Status:On

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

Project:

Sleep Timer:

800x480

N/A

5 Minutes

Audio

Master Volume:

Master Mute:Off

Advanced

Controller IP:N/A

Project Size:N/A

TLP Pro 520M and TLC Pro 521M • Setup Guide (Continued)

Figure 8. TLP Pro 520M Setup Menu

Reset Modes: a Brief Summary

The TLP Pro 520M and TLC Pro 521M offer the following reset modes:

• Use factory firmware: Press and hold the Reset button (ﬁgure 4, D) while applying power to the unit. Use this

mode to replace rmware in the event of rmware failure.

• Project Recovery:

(TLC Pro 521M only)

This mode is activated using Global Congurator Plus and Professional. See the

Global Conﬁgurator Help File for more information.

• Reset All IP Settings: Press and hold the Reset button for 6 seconds. After the Reset LED (ﬁgure 4, C) ashes

twice, release and momentarily press the Reset button. Use this mode to reset all network

settings without affecting user-loaded les.

• Reset to Factory Defaults: Press and hold the Reset button for 9 seconds. After the Reset LED ashes three times,

release and momentarily press the Reset button. Use this mode to return the interface to

factory default settings.

Setup Menu

The setup menu opens when the menu button is pressed (see Front Panel

Features, Gon page 3). Figure 8 shows the TLP Pro 520M menu. The

setup menu for the TLC Pro 521M is very similar.

There are ve different screens: Status, (shown in gure 8) Network,

Display, Audio, and Advanced. The screens can be selected by pressing

the appropriate button in the navigation bar at the top of the screen (for

more information, see the TLPPro 520M and TLC Pro 521M User Guide).

Andere Handbücher für TLP Pro 720M

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extron electronics Touchscreen Handbücher

Extron electronics

Extron electronics TLP Pro 720C Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1230WTG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 725T Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 525T Series Bedienungsanleitung

Extron electronics

Extron electronics TLP 1000MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720C Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TouchLink TLP 710CV Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1220TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1520TG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225TG Bedienungsanleitung

Extron electronics

Extron electronics SMK 2 Bedienungsanleitung

Extron electronics

Extron electronics Scan Rate Indicator SRI 200 Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225MG Bedienungsanleitung

Extron electronics

Extron electronics TLP 700MV Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 725T Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 300M Series Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 1225MG Bedienungsanleitung

Extron electronics

Extron electronics TLP Pro 720M Bedienungsanleitung

Extron electronics

Extron electronics TLP 700TV Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung