Extron electronics DTP T USW 233 Bedienungsanleitung

DTP T USW 233 • Setup Guide

This guide provides instructions for an experienced installer to set up and operate the

Extron DTP T USW 233 switching video transmitter. The DTP T USW 233 transmitter switches among

an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver, can

extend the selected signal up to 230 feet (70 m). If the selected input is HDMI, the extended video

signal is HDCP-compliant.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transmitter as required.

Step 2 — Making Connections

Inputs

AInput 1 (RGB) connector — Connect a VGA cable between this port and the VGA output port of the analog video source.

BInput 2 and 3 (HDMI) connectors — Connect HDMI cables between these ports and the HDMI output ports of the digital video

sources.

NOTE: See the LockIt®Lacing Brackets on page 3 of this guide to securely fasten the HDMI connectors to the transmitter.

CAudio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.

NOTE: Analog input audio is not embedded in the HDMI signal; it is transmitted separately and is present for any selected input.

Over DTP RS-232 and IR pass-through

DRS-232 and IR connector — To pass serial or infrared data or control signals on the Over

DTP RJ-45 output, connect the controlling device to the transmitter via the RS-232 and IR

captive screw connector. Connect the device to be controlled to the receiver.

DTP output to receiver

EDTP RJ-45 connector — Connect the transmitter DTP Out port to the DTP In port on the

receiver. Extron recommends that you terminate both cable ends in accordance with the

following specications, at a minimum:

• TIA/EIA T 568B •Shielded cable

• 24 AWG, solid conductor

ATTENTION: Do not connect this device to a computer data or telecommunications network.

Signal LED — Lights when the unit is outputting a TMDS clock signal on the DTP output.

Link LED — Lights when a valid link is established between the units on the DTP cable.

Remote control

FRemote Contact port — If desired, for contact closure control, plug a locally-contructed contact closure control device into this

3.5 mm, 4-pole captive screw port. Momentarily short the pin for the desired input (1, 2, or 3) to G to select that input. To force an

input to be always selected, leave the short in place.

NOTES:

• Contact closure control overrides front panel input selections.

• For contact closure control, auto-input switching mode must be off (see Selecting the switch mode on the next page).

POWER

12V

--A MAX

Rx GTx RxTxG

RS-232 IR

RxTx

RGB, Y, R-Y, B-Y HDMI HDMI

SIG LINK

DTP OUT

AUDIO

CONTACT RS-232TALLY

123G 123+V

RESET

INPUTS

OVER DTPREMOTE

AAJJCCBBBBEEDDFFGGIIHH

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIAT

568B

TP Wires

12345678

Pins:

TxRx

RxTx

Gnd

IR Device

RS-232 Device

RxTx RxTxG

RS-232 IR

OVER DTP

DTP T USW 233 • Setup Guide (Continued)

GRemote Tally port — If desired, to remotely identify the currently selected input, plug a locally-constructed device into this 3.5 mm,

4-pole captive screw connector. Connect the power wire for the device into the +V pin and connect the ground wire for the each

indicator into the corresponding tally output pin: 1, 2, or 3.

When an input is selected, by either contact closure or front panel selection, the corresponding tally output pin shorts to ground,

closing the circuit and lighting the connected indicator (LED).

HRemote RS-232 port — Plug a serial RS-232 device into the switching transmitter via this rear

panel 3.5 mm, 3-pole captive screw connector for remote control of the switching transmitter.

Reset button

IReset button — This button initiates two levels of reset. For different reset levels, use an

Extron Tweeker or small screwdriver to press and hold the recessed button while the switcher

is running or while applying power. See the DTP T USW 233 User Guide, available at www.extron.com, for details.

Power

JPower connector — Connect an IEC power cord between the included 12 VDC

power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to

either unit, transmitter or receiver, as shown at right. Use the included tie-wrap to

strap the cord to the captive screw connector.

NOTE: Only one power supply is required. A single power supply connected to

either unit in the Tx/Rx pair powers both units. A power supply is included

with the transmitter.

Front panel Conﬁguration port

AConfiguration port — Plug a PC or other controlling device into the switching

transmitter via this front panel mini-USB connector for remote conguration of the switching transmitter.

Operation

Switching inputs

Select the desired input by pressing the associated input button. Observe that the

LED for the selected input lights.

NOTE: The switcher must be in normal (manual) mode (see below).

Selecting the switch mode

In auto-input switching mode, the switcher selects to the highest numbered input

with a sync signal present. Turn auto-input switching mode on and off as follows:

1. Press and hold the Mode (Input 1) button and the button

for the desired mode for approximately 5 seconds:

Auto (Input 3) — TheAuto Switch LED lights.

Normal (Input 2) — TheAuto Switch Active LED goes off.

2. Release the buttons.

Locking and unlocking the front panel

(Executive mode)

The switcher has a front panel lock feature that locks the front panel. If you try to make

front panel input selections when the panel is locked, all front panel LEDs ash three

times. Toggle the front panel lock on and off by pushing and holding all three Input

buttons simultaneously for 5 seconds. All front panel LEDs ash three times.

Release the buttons.

Interpreting the Status LEDs

Signal LEDs (1 through 3) —Indicate that the switcher detects horizontal sync

(Signal LED 1) or TMDS clock (Signal LED 2 and Signal LED 3) signals on the associated input.

HDCP LEDs (2 and 3) —Indicate that the corresponding input signal is HDCP encrypted.

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) Max.

SECTION A–A

REMOTE

RxTx Gnd

RS-232 Device

GRxTx

RS-232

AUTO

SWITCH

CONFIG

MODE NORMAL

AUTO

Press the button.

The LED lights

green.

123

MODE NORMAL AUTO

AUTO

SWITCH

Press and HOLD the Mode button

and either the Auto or Normal button.

Release the buttons.

uto Switch lights (auto)

or goes out (normal).

seconds

MODE NORMAL AUTO

Press the and

HOLD

the all three Input buttons.

All three LEDs flash three times. Release the Input buttons.

HDCP

SIGNAL

STATUS

123

LockIt®Lacing Brackets

Use the included LockIt Lacing Brackets to securely fasten both HDMI cables as follows.

1. Plug the HDMI cable into the panel connection.

2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt lacing

bracket to be placed over it. The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten the

screw to secure the bracket.

ATTENTION:Do not overtighten the HDMI connector mounting screw. The shield it fastens to

is very thin and can easily be stripped.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as

shown.

5. While holding the connector securely against the lacing bracket, use pliers or similar tools to

tighten the tie wrap, then remove any excess length.

Application Diagram

Figure 1. Typical Switching Transmitter Application

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

HDCP

HDMI IN

AUDIO IN

HDCP

TLP 1000

IPCP 505

IN1608

DTP HDMI 230 Rx

Projector

100-240V ~ -- A MAX

CONFIGURABLE

HDMI HDMI

RS-232 IR

RS-232IR

Tx Rx Tx RxG

Tx Rx Tx RxG Tx Rx Tx RxG

HDMI

INPUTS OUTPUTS

Tx Rx

RS-232

LAN

2x25W(8Ω)/2x50W(4Ω)

RESET

AUDIO INPUTS OUTPUTS

REMOTE

LL1R R

L2 R

CLASS 2 WIRING

L4R

L5R

+48V

VARIABLE

IN1608 SA

MIC/LINE

L6R

SIG LINK

DTP IN

SIG LINK

DTP IN

SIG LINK

DTP OUT

50/60 Hz

RS-232IR

OVER DTP

AMPLIFIED OUTPUT

VOLUME

SCALING PRESENTATION SWITCHER

IN1608

INPUTS

HDCP

SIGNAL

OUTPUTS

ENTER

Extron

2 3 4 5 6 7 8 A B C

INPUTS

1 2 3 4 5 6 7 8

CONFIG

Ext

ron

DTP T U

SW 233

ansmitter

Extron

DTP T HWP 232 D Tx

Transmitter

Ethernet

Network

POWER

12V

0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

XTP DTP 24 Cable

230'

HDMI

12345678

100

LINK

ACT

COM

IR/S

RTS

CTS

RELAY FLEX

I/O

eBUS

ACT LIMIT

OVER

SWITCHED

12VDC

OVER

LIMIT

IPCP 505

608

60 H

xtron

TP T U

W 233

ransmitterXTPDTP 24

abl

230

AUTO

SWITCH

DTP T USW 233

12 3

CONFIG

231STATUS

SIGNAL

HDCP

68-2490-50 Rev. B

03 14

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Andere Handbücher für DTP T USW 233

Inhaltsverzeichnis

Andere Extron electronics Sender Handbücher

Extron electronics

Extron electronics FOX3 T 201 Bedienungsanleitung

Extron electronics

Extron electronics PowerCage MTP AV Series Bedienungsanleitung

Extron electronics

Extron electronics XTP T VGA Bedienungsanleitung

Extron electronics

Extron electronics FOXBOX T HD-SDI Bedienungsanleitung

Extron electronics

Extron electronics PVT RGB D Plus Bedienungsanleitung

Extron electronics

Extron electronics XTP FT HD 4K Bedienungsanleitung

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 202 FB Bedienungsanleitung

Extron electronics

Extron electronics DVI 201 Tx/Rx Bedienungsanleitung

Extron electronics

Extron electronics DTP T UWP 4K 232 D Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 203 Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 201 D Series Bedienungsanleitung

Extron electronics

Extron electronics DTP T HWP D Series Bedienungsanleitung

Extron electronics

Extron electronics DTP2 T 201 D Bedienungsanleitung

Extron electronics

Extron electronics XTP T VGA Bedienungsanleitung

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Extron electronics

Extron electronics DTP3 T 203 Bedienungsanleitung

Extron electronics

Extron electronics A/V Receiver MTP 4T 15HD RS Bedienungsanleitung

Extron electronics

Extron electronics XTP T FB 202 4K Bedienungsanleitung

Extron electronics

Extron electronics DTP DVI 330 Bedienungsanleitung

Extron electronics

Extron electronics MTP 15HD A Series Bedienungsanleitung

Extron electronics

Extron electronics XTP T HWP 101 Bedienungsanleitung

Extron electronics

Extron electronics DVI 201xi TX Bedienungsanleitung

Extron electronics

Extron electronics MTP T 15HD A Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung