Ezviz C3A & W2D Bedienungsanleitung
C3A+W2D
User Manual
1
Chapter 1 Overview
1.1 Brief Introduction
You can use your camera wirelessly, powered by the battery. Also, you can use it indoors
with an AC power outlet connected, or use it outdoors with a solar panel. Once motion is
detected by the camera, you can check the messages in the APP through the Wi-Fi linked
to the base station.
1.1.1 The Appearance of the Device
The appearance of the device is shown below.
Figure 1-1 Appearance
Figure 1-2 Appearance Instruction
2
Chapter 2 Power on Your Device
Your camera comes with accessories that you can use to create a custom security
system that meets your individual needs.
Notes:
For wireless use: Before you use your camera wirelessly, we recommend that
you charge the battery, referring to 2.1 How to Charge the Battery.
For wired use:
1. Indoor: Connect the power adapter to an indoor electrical outlet, referring to
2.1.2 Power Adapter.
2. Outdoor: If you want to install your camera outdoors, use the solar panel
(sold separately), referring to 2.1.3 Solar Panel (Sold Separately) .
2.1 How to Charge the Battery
2.1.1 Charging Station (Sold Separately)
You can use the charging station (sold separately) to charge the battery.
Steps:
1. Insert the battery into one of the battery slots.
Figure 2-1 Insert the Battery
2. Connect the power cable to the power adapter.
3. Connect the charger with an indoor electrical outlet via power adapter (5V 2A).
Figure 2-2 Wiring
Note:
When the battery is fully charged, the LED indicator of charging station turns green.
4. After charging the battery, hold on the clasps until you pull out the battery.
3
Figure 2-3 Pull out the Battery
2.1.2 Power Adapter
You can use the power adapter to charge the battery.
1. Install the Battery
Steps:
(1) Unlock the battery compartment by pressing and holding the latch, at the same
gently pull back the battery cover to open the compartment.
(2) Pull the battery buckle upwards and insert the battery.
(3) Insert a micro SD card into the micro SD card slot if needed (See 8.1 Insert a
Micro SD Card).
(4) Close the battery cover.
Figure 2-4 Install the Battery
Note:
Write down the verification code located on the battery, you are required to input it when
you live view or play back the video.
2. Charge Your Camera Battery
Steps:
(1) If the camera is outdoor, bring it in to charge the battery.
(2) Connect the power cable to the power adapter.
(3) Connect the camera with an indoor electrical outlet via power adapter (5V 2A).
4
Figure 2-5 Charge the Battery
Note:
The camera LED indicator status is shown as below.
Battery charging: Slow-flashing red.
Battery fully charged: Off.
2.1.3 Solar Panel (Sold Separately)
You can use the solar panel (sold separately) to charge the battery.
Steps:
1. Install the battery (See Install the Battery in 2.1.2 Power Adapter).
2. Connect the camera to the solar panel.
Figure 2-6 Use Solar Panel to Charge the Battery
Notes:
When the battery is fully charged, the camera LED indicator turns solid blue.
As an alternative charging equipment, the power amount generated by this solar
panel may be affected by its actual surrounding environment, mainly the
intensity of sunlight and the time length of illumination. If the battery camera is
running out of power soon, you are recommended to charge the battery by
charging station or power adapter, as the solar panel alone cannot ensure the
camera normal working status.
The camera LED indicator status is shown as below.
Battery charging: Slow-flashing red.
Battery fully charged: Off.
5
Chapter 3 Connect Your Base
Station to the Internet
The base station connects to your home network and allows you to view your camera
videos from anywhere.
1. Connect the power cable to the power adapter.
2. Connect the power adaptor to an indoor electrical outlet (5V 2A).
Figure 3-1 Power on the Base Station
Note:
The circular LED indicator (SYNC Button) turns solid blue, when the base station is started
up.
3. Connect the base station to an open LAN port on your router using the included
Ethernet cable.
Figure 3-2 Connect the Base Station to the Network
Note:
The circular LED indicator (SYNC Button) turns solid green, when the base station is
connected to the network.
6
Chapter 4 Get the EZVIZ App
Download the free EZVIZ app to set up your base station and camera. This app provides
step-by-step instructions.
Steps:
1. Connect your mobile phone to the Internet.
2. Search for EZVIZ in the App Store or Google Play (TM).
3. Download and install the EZVIZ app.
4. Launch the app, register an EZVIZ user account.
EZVIZ APP
Note:
If you have already used the app, make sure that it is the latest version. To find out if an
update is available, go to the App store and search for EZVIZ.
7
Chapter 5 Use the EZVIZ App for
Installation and Setup
Use the EZVIZ app to install and set up your base station and camera. The EZVIZ app
guides you through setup in this order:
1. Create your EZVIZ account. You can use the same account to manage all your
EZVIZ devices.
2. Connect the EZVIZ base station to the Internet and add it to your account.
3. Link each EZVIZ camera with the base station.
Steps:
1. Connect your mobile device to the Internet.
2. Log in the EZVIZ App.
3. At the Home screen, tap “+” on the upper-right corner to go to the scan QR code
interface.
Figure 5-1 Home Screen
4. Scan the QR code on base station or manually enter the serial number to go to
the Add Device Interface.
Figure 5-2 Scan the QR Code
5. Tap Add button.
6. Please make sure your base station is powered on.
The circular LED indicator (SYNC Button) turns solid blue, when the base station is started up.
8
7. Please make sure your base station is connected to the network, and tap Next
button.
Figure 5-3 Confirm
The circular LED indicator (SYNC Button) turns solid green, when the base station is connected to the network. Please
wait patiently for the base station to be added to your EZVIZ account.
8. Your EZVIZ app turns to Device Setup Interface, when the base station is added
to your EZVIZ account successfully.
Figure 5-4 Device Setup Interface
9
9. Tap View Device button to go to your base station setup interface.
10. Tap Go to Add button to link camera(s) to your base station.
You can also tap the Finished button to finish the settings.
Figure 5-5 Device Setup Interface
Before the synchronization, it is suggested to fully charge your camera.
After the battery is charged, and before the synchronization progress, please disconnect all the charging
cables.
11. Once your camera is fully charged, bring it close to the base station (within 2
feet to 3 feet (0.6 to 1 m)).
Figure 5-6 The Distance between Base Station and Camera
12. Tap Next button.
13. Press and hold the SYNC button on the camera for about 6 seconds until you
hear your camera has been reset successfully.
Inhaltsverzeichnis
Andere Ezviz Sicherheitskamera Handbücher
Ezviz
Ezviz CS-H3 Bedienungsanleitung
Ezviz
Ezviz C1C Bedienungsanleitung
Ezviz
Ezviz CS-LC1-A0-1B2WPFRL Bedienungsanleitung
Ezviz
Ezviz C3N Bedienungsanleitung
Ezviz
Ezviz H3-R100 Bedienungsanleitung
Ezviz
Ezviz CP1 Bedienungsanleitung
Ezviz
Ezviz Mini 360 Plus Bedienungsanleitung
Ezviz
Ezviz Mini O Bedienungsanleitung
Ezviz
Ezviz Mini Trooper Bedienungsanleitung
Ezviz
Ezviz EB3 Bedienungsanleitung
Ezviz
Ezviz C4W Bedienungsanleitung
Ezviz
Ezviz DP2 Bedienungsanleitung
Ezviz
Ezviz CS-CV248 Bedienungsanleitung
Ezviz
Ezviz C6N Bedienungsanleitung
Ezviz
Ezviz C3A Bedienungsanleitung
Ezviz
Ezviz LC1C Bedienungsanleitung
Ezviz
Ezviz C1C Bedienungsanleitung
Ezviz
Ezviz C1C Bedienungsanleitung
Ezviz
Ezviz C6W Bedienungsanleitung
Ezviz
Ezviz CTQ3N Bedienungsanleitung
