FAAC ParQube FC Benutzerhandbuch

ParQube FC

Fee Computer

Use and maintenance

Ver. 1.0

July, 2015

Instructions translated from the original Italian

3 / 36

Ver. 1.0 - July, 2015 - EN

MANUFACTURER

FAAC S.p.A.

Soc. Unipersonale

Via Calari 10

40069 Zola Predosa (BO)

Italy

INTRODUCTION

This documentation is part of the operating instructions of the parking system.

If this manual should contain incomplete or dicult to understand information, it is mandatory to consult the installer: no

initiative is to be taken.

GENERAL INFORMATION

FAAC S.p.A. requires installers and users to strictly comply with the instructions described in this manual, paying particular

attention to the safety warnings.

GENERAL CONSIDERATIONS

All operating and maintenance instructions and warnings given in this manual must be complied with.

Training the personnel responsible for the product is of particular importance, especially with regards to the use, as well as

maintenance and monitoring of compliance with the operating procedures and all safety regulations in this manual.

This manual has been drawn up with the greatest possible care, with the aim of providing accurate information. However,

FAAC S.p.A. declines all explicit and implicit liability for any errors contained in this document.

Moreover, FAAC S.p.A. reserves the right to modify the contents of this manual at any time and without prior notice in order

to keep it up to date.

FAAC S.p.A. shall not be held responsible for errors or data loss deriving from the use of this manual.

ORIGINAL VERSION IN ITALIAN

Versions of this document in a language dierent from the original must be understood to be a direct translation of the

original Italian version.

PREFERENTIAL RIGHT OF INTERPRETATION

In the event of any dierences between the translated and the original version, the Italian version shall be considered the

only valid version published and recognised by FAAC S.p.A.

No part of this publication may be reproduced, distributed, translated into any language or transmitted by any means,

electronic or mechanical, including photocopying, recording or with any other storage and retrieval systems, for other pur-

poses other than the exclusive personal use of the purchaser, without specic written permission from FAAC S.p.A..

FAAC S.p.A. thanks you for choosing our products

4 / 36 Ver. 1.0 - July, 2015 - EN

5 / 36

Ver. 1.0 - July, 2015 - EN

Table of Contents

1 Graphic conventions .................................................................................................................................8

1.1 General symbols..........................................................................................................................................................................8

1.2 Symbols for procedures ............................................................................................................................................................8

1.2.1 Table with the symbols for procedures................................................................................................................................................... 9

1.3 Roles............................................................................................................................................................................................. 10

2 General Conditions.................................................................................................................................. 12

2.1 Symbols applied to the Product............................................................................................................................................ 12

2.2 General Warnings ..................................................................................................................................................................... 12

2.3 Limitations of liability................................................................................................................................................................ 12

2.4 Recipients.................................................................................................................................................................................... 12

3 Product Description ................................................................................................................................ 14

3.1 Intended use .............................................................................................................................................................................. 14

3.1.1 Limitations of use ........................................................................................................................................................................................14

3.1.2 Storage ..........................................................................................................................................................................................................14

3.2 Technical characteristics........................................................................................................................................................... 15

3.2.1 Control elements.........................................................................................................................................................................................15

3.3 General description .................................................................................................................................................................. 16

3.3.1 Functionality .................................................................................................................................................................................................16

4 Use...............................................................................................................................................................20

4.1 Use by the operator ................................................................................................................................................................ 20

5 Maintenance ............................................................................................................................................ 24

5.1 Introduction............................................................................................................................................................................... 24

5.2 Safety warnings ........................................................................................................................................................................ 25

5.3 Service and Maintenance planning systems..................................................................................................................... 26

5.3.1 Peripheral .....................................................................................................................................................................................................26

5.3.2 Ticket/receipt printer .................................................................................................................................................................................26

5.4 Peripheral................................................................................................................................................................................... 27

5.4.1 Opening service door............................................................................................................................................................................... 27

5.4.2 Closure service door ................................................................................................................................................................................. 27

5.4.3 Switching on and o .................................................................................................................................................................................28

5.5 Ticket/receipt printer............................................................................................................................................................... 29

5.5.1 Paper roll replacement..............................................................................................................................................................................29

5.5.2 Clearing jams................................................................................................................................................................................................31

6 Declaration of Conformity.................................................................................................................... 34

6 / 36 Ver. 1.0 - July, 2015 - EN

This page intentionally left blank

7 / 36

Ver. 1.0 - July, 2015 - EN

Capitolo 1

GRAPHIC CONVENTIONS

8 / 36 Ver. 1.0 - July, 2015 - EN

1 GRAPHIC CONVENTIONS

1.1 GENERAL SYMBOLS

The following table shows the general symbols used in the manual.

Symbol Description

Indicates warnings or procedures related to operator safety.

Indicates warnings or information of particular importance which do not aect operator safety.

Indicates a reference to a specic manual

Indicates a reference to a chapter in this manual

Indicates a reference to a section in this manual

1.2 SYMBOLS FOR PROCEDURES

Each procedure reports, next to the title, an icon indicating the role to be performed.

In addition, certain repetitive procedures are associated with an icon that will be used to recall them each time they should

be executed.

Apertura sportello di servizio

12 3

Figure 1 - Example of a title of a procedure

Pos Description

1Title procedure

2Icon identifying the procedure (for recursive procedures only)

3Minimum role to perform the procedure

9 / 36

Ver. 1.0 - July, 2015 - EN

1.2.1 Table with the symbols for procedures

Icon Description

Indicates the opening of service door

Indicates the closing of the service door

Indicates the activation of the security measures

Indicates the deactivation of the security measures

ONON

Indicates the switching on

OFFOFF

Indicates the switching o

Indicates the connection

Indicates the disconnection

Indicates the cleaning

Indicates the insertion of the tickets or card

Indicates the withdrawal of the tickets or card

Indicates the emptying of the bin

Indicates the Login phase

10 / 36 Ver. 1.0 - July, 2015 - EN

1.3 ROLES

The following table indicates the expertise and qualications required of the operators assigned to the dierent tasks:

Icon Qualication Description Responsibility

INSTALLER

▫Technician

HUB Parking Technology

▫Technician who has

received specic training

from the manufacturer.

▫System installation according to the

intended purpose.

▫Commissioning according to the

operating and safety requirements and

delivery to the system manager.

▫Training of operational personnel to

ensure safe operation.

▫System maintenance by repairing or

replacing components.

MAINTENANCE TE-

CHNICIAN

▫Technician

HUB Parking Technology

▫Technician or employees of

the parking area trained by

the manufacturer.

▫System maintenance by repairing or

replacing components.

▫Cleaning of the equipment in accordance

with the manufacturer's instructions.

▫Immediate and safe reaction in case of

faults.

SYSTEM MANAGER ▫Car park owner

▫Parking employee

▫Ensure that maintenance is performed

only by authorised technicians

▫Ensure that all safety regulations are

observed

▫Check that the operators have specic

training

OPERATOR ▫Parking employee.

▫Operation of the peripherals during

normal use.

▫Cleaning of the equipment in accordance

with the manufacturer's instructions.

▫Immediate and safe reaction in case of

faults.

Inhaltsverzeichnis

Andere FAAC Zahlungsterminal Handbücher

FAAC

FAAC PARQUBE APS Bedienungsanleitung

Beliebte Zahlungsterminal Handbücher anderer Marken

PAX

PAX D180SRF Bedienungsanleitung

LinkPoint

LinkPoint AIO Bedienungsanleitung

Moneris

Moneris hispeed 6200 Bedienungsanleitung

Moneris

Moneris iWL220 Bedienungsanleitung

Ingenico

Ingenico iUC280 Bedienungsanleitung

Ingenico

Ingenico Tetra Move/5000 Bedienungsanleitung

Ingenico

Ingenico iWL250B Bedienungsanleitung

Optimum

Optimum M4230 Bedienungsanleitung

Triton

Triton RL5000 Bedienungsanleitung

Ingenico group

Ingenico group Lane/8000 Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals Infinea Tab Lite Bedienungsanleitung

PAX

PAX S920 Bedienungsanleitung

dejavoo

dejavoo Z Series Bedienungsanleitung

Ingenico

Ingenico iCT220, iCT250 Bedienungsanleitung

VeriFone

VeriFone VX 520 Series Bedienungsanleitung

Optomany

Optomany axept S900 Bedienungsanleitung

Skyzer

Skyzer iWL252 BLUETOOTH Bedienungsanleitung

Moneris

Moneris iWL220 Bedienungsanleitung