Fagor BMF-300X Bedienungsanleitung

BMF-300X

24” REFRIGERATOR

Refrigerador de 24”

Write the serial number here: _______________

Installation Manual

Manual del Instalación

Installing your New Appliance

Before using the appliance for the ﬁrst time,

review the following tips.

Ventilation of Appliance

To ensure the proper working conditions,

air must be allowed to circulate behind and

above the refrigerator. Leave at least 25/64

inch (10 mm) of space between the back

wall and the refrigerator condenser, and at

least 25/64 inch (10 mm) between the top

of the refrigerator and the cabinet or ceiling

above it. Leave at least 19/64 inch (7.5 mm)

of space between each side and a clear

space in front to allow the doors to open

135°.

Dimensions of the appliance with door

(Height x Width x Depth): 72.83” x 23.42”

x 26.9”.

Dimensions of the appliance without door

(Height x Width x Depth): 71.53” x 23.42”

x 23.03”.

Note:

• This refrigerator can be inserted into a

kitchen cabinet. The space must have

the following minimum dimensions

shown in the ﬁgure above.

“A” : 24 1/64” (610mm)

“B” : 79 17/32” (2020mm)

“C” : 23 27/64” (595mm)

Minimum installation clearance

Top: 25/64 inch (10 mm)

Back: 25/64 inch (10 mm)

Left Side: 19/64 inch (7.5 mm)

Right Side: 19/64 inch (7.5 mm)

25/64” Min.

clearance from

the cabinet

19/64” Min.

clearance from

a corner to

achieve 90°

door swing.

90° Swing

required for

pull-out shelf

clearance.

23 27/64” Min. clearance

for door swing.

Top of Refrigerator

• Do not install the refrigerator outdoors or

where it can be exposed to rain. Install

your appliance in a dry room and avoid

high humidity areas such as basements

and garages.

• Install the refrigerator away from heat

sources and protect it from direct

sunlight in order to conserve energy.

Leveling the Appliance

• For sufﬁcient leveling and air circulation

in the lower rear section of the appliance,

the bottom feet may need to be adjusted.

You can adjust them manually or by

using a suitable spanner.

• The unit will not function properly if tilted

more than 25/64” (10 mm). Please level

the unit as ﬂat as possible.

Installing the Door Handles

For transportation convenience, the door

handles are separately packaged in a plastic

bag. To install the handles, follow the steps

below.

1. Remove screw covers on the left side of

the door and put them into the plastic

bag.

2. Place the handle on the left side of

the door, align the screw holes with

the handle and attach with the screws

provided. Then install the handle covers.

Reversing the Door Hinge

The side which the door opens on can be

changed from the right side (as supplied)

to the left side. Disconnect the refrigerator

from the power outlet and remove products

stored on the inside of the door.

WARNING: This procedure should only be

carried out by qualiﬁed individuals. Certain

aspects of this procedure may require two

people.

Tools you will need:

Note: When laying the refrigerator on its

back to gain access to the base, you should

rest it on a soft foam pad or similar material to

avoid damaging the back of the refrigerator.

To reverse the door, the following steps are

recommended.

1. With the refrigerator upright, open the

upper door to take out all door racks (to

avoid rack damage) and then close the

door.

≤25/64” (10mm)

8mm socket wrench

8mm wrench

Flathead screwdriver

Phillips screwdriver

Door racks

2. Remove the upper cover on the top of

the refrigerator starting from the right

side and then remove the upper cover of

the upper door.

4. Remove the upper hinge by removing the

three self-tapping screws indicated in the

image below.

Note: Please hold the upper door by hand

during step 4 to prevent door from dropping.

5. Remove the upper door by lifting

vertically and place it on a smooth

surface with the panel facing upwards.

Remove the handle screw covers and

screw hole covers, then remove the self

tapping screws. Remove the handle and

switch it to the right side, then install

the self-tapping screws, handle screw

covers and screw hole covers.

Loosen the self-tapping screws, detach

the stop block and door holder. With the

handle in place, reinstall the door holder

and the spare stop block found in the

plastic bag. Do not use the one you just

removed, that one must be stored in the

plastic parts bag.

Then remove the corner cover and the

upper hinge cover, this may require you

to slightly open the door. Put all parts

into the plastic parts bag.

3. Disconnect all the wiring harness

connectors and ground wires.v Remove

cover on the cabinet body shown in

image 3.

6. Loosen screws used to hold the middle

hinge and remove middle hinge. Then

remove the lower door.

9. Place the refrigerator ﬂat on the ﬂoor,

remove adjustable feet and self-tapping

screws. Remove the front foot ﬁxed

bracket and lower hinge.

10. Unscrew the lower hinge, change it

to the opposite side and reattach and

mount washer.

11. Change lower hinge part to the left

side and front foot ﬁxed board to the

right side, then fasten with self-tapping

screws. Finally install adjustable feet.

12. Install the lower door by sliding it in a

downward motion and align the lower

hole site on the bottom of the door and

the upper hinge site. Turn the middle

hinge piece 180°, change the washer

on the axis to the upper side, adjust the

middle hinge to the appropriate position

and then reinstall it.

7. Place the lower door on a smooth

surface facing upwards. Change the

handle to the right side by following step

5 described in page 7. Remove the self-

tapping screws, detach the stop block

and door holder.

Turn the door holder 180° and then

install it and the spare stop block on

the opposite side with the self-tapping

screws.

8. Place the screw hole covers on the

middle plate on the opposite side.

Washer

Note: The washer may

stick to lower door.

Note: The washer may

stick to lower door.

Washer

13. Unscrew the upper hinge axis, turn the

upper hinge over and ﬁx axis on it. Then

place it aside for later use.

14. Reconnect the wires on the left and right

slots of the refrigerator body.

15. Place the door in the correct position.

Move the ground wire into the slot on

the upper door from right to left and then

fasten the upper hinge and ground wire

with the self-tapping screws. Hold door

in place when installing.

16. Install the upper hinge cover (in plastic

bag) and reconnect any remaining wires.

17. Turn the corner cover of the door 180°

and install it onto the right corner of the

upper door, then mount the upper cover

of the upper door.

18. Take the connector out of the cover and

mount it on the spare cover (found in

spare parts bag, marked with an R). Put

the cover you just removed in the parts

bag.

Note: Be sure the front side of the

connector ﬁts correctly when mounting.

19. Install the corner cover, connect the wire

and install the upper cover of the upper

door.

20. Open the upper door, mount door racks

and then securely close the door.

Instalación de su Electrodoméstico

Antes de utilizar el electrodoméstico por

primera vez, lea los siguientes consejos.

Ventilación del Electrodoméstico

Para asegurar condiciones interiores

adecuadas, el aire debe poder circular por

detrás y por encima de la nevera. Deje

por lo menos 25/64 “(10 mm) de espacio

entre la pared posterior y el condensador

del refrigerador, y por lo menos 25/64” (10

mm) entre la parte superior de la nevera y el

armario o el techo por encima de ella. Deje

por lo menos 19/64 “(7.5 mm) de espacio

entre cada lado y un espacio libre delante

para permitir que las puertas se abran 135°.

Dimensiones del electrodoméstico con la

puerta (Altura x Anchura x Profundidad):

72.83” x 23.42” x 26.9”.

Dimensiones del electrodoméstico sin la

puerta (Altura x Anchura x Profundidad):

71.53” x 23.42” x 23.03”.

Note:

• Este refrigerador puede ser instalado

en un mueble de cocina. El espacio

debe tener las siguientes dimensiones

mínimas que se muestran en la ﬁgura de

arriba.

“A” : 24 1/64” (610mm)

“B” : 79 17/32” (2020mm)

“C” : 23 27/64” (595mm)

Distancia mínima de instalación

Por Encima: 25/64 inch (10 mm)

Por Detrás: 25/64 inch (10 mm)

Lado Izquierdo: 19/64 inch (7.5 mm)

Lado Derecho: 19/64 inch (7.5 mm)

25/64” Distancia

mínima del gabinete.

19/64” Distancia

mínima desde

una esquina para

abrir la puerta.

90° Espacio

requerido para

abrir el cajón.

23 27/64” Espacio mínimo

para apertura de la puerta.

Parte Superior del Refrigerador

• No instale el refrigerador al aire libre o

donde pueda estar expuesto a la lluvia.

Instale el electrodoméstico en un lugar

seco y evite áreas con alta humedad

como sótanos y garajes.

• Instale el refrigerador lejos de fuentes de

calor y protéjalo de la luz solar directa

para conservar la energía.

Nivelación del Electrodoméstico

• Para la nivelación suﬁciente y la

circulación de aire en la sección inferior

trasera del electrodoméstico puede ser

necesario ajustar los pies abajo. Usted

puede ajustar de forma manual o usando

una llave adecuada.

• El electrodoméstico no funcionará

correctamente si está inclinado más de

25/64 “(10 mm). Nivele la unidad lo más

plano posible.

Instalación de los Mangos de Puerta

Para comodidad de transporte, los mangos

están envasados en una bolsa plástica.

Para instalar los mangos, siga los pasos a

continuación.

1. Retire las cubiertas de los tornillos en el

lado izquierdo de la puerta y pongalas

en la bolsa plástica.

2. Coloque el mango al lado izquierdo de la

puerta, manteniendo los oriﬁcios de los

tornillos en el mango y la puerta en línea,

como muestra la imagen.

Inversión de la Puerta

El lado que se abre la puerta se puede

cambiar desde el lado derecho (como se

suministra) al lado izquierdo. Desconecte el

refrigerador del tomacorriente y retire todos

los alimentos en la puerta.

AVISO: Este procedimiento sólo debe ser

realizado por personas cualiﬁcadas. Ciertos

aspectos de este procedimiento puede

requerir dos personas.

Herramientas necesarias:

Nota: Al colocar el refrigerador en su parte

posterior para obtener acceso a la base,

debe ponerla en una almohadilla de espuma

blanda o material similar para evitar dañar

la parte trasera del refrigerador. Para invertir

la puerta, se recomiendan los siguientes

pasos.

1. Con el refrigerador vertical, abra la

puerta superior para sacar todos los

estantes de la puerta (para evitar daños)

y cierre la puerta.

≤25/64” (10mm)

Destornillador de punta ﬁna

Llave ﬁja de 8 mm Destornillador de estrella

Llave de 8 mm

Andere Handbücher für BMF-300X

Inhaltsverzeichnis

Sprachen:

Andere Fagor Kühlschrank Handbücher

Fagor

Fagor 3FFV-855R Bedienungsanleitung

Fagor

Fagor 3FFK-6645 Bedienungsanleitung

Fagor

Fagor FA3702 Bedienungsanleitung

Fagor

Fagor 3FIB-1725 Bedienungsanleitung

Fagor

Fagor FFJ2667AX Bedienungsanleitung

Fagor

Fagor QVR-1 N Einfaches Handbuch

Fagor

Fagor BMF-200X Bedienungsanleitung

Fagor

Fagor Ingenious Bedienungsanleitung

Fagor

Fagor 3FFK-6625X Bedienungsanleitung

Fagor

Fagor 3FIC-370 Bedienungsanleitung

Fagor

Fagor QR-1 Bedienungsanleitung

Fagor

Fagor FC-39 LA Bedienungsanleitung

Fagor

Fagor FIC-541UK Bedienungsanleitung

Fagor

Fagor FUR-27-N Einfaches Handbuch

Fagor

Fagor Refrigerator Instructions for Leitfaden

Fagor

Fagor 3FFK-1875 Bedienungsanleitung

Fagor

Fagor FIC-381E Bedienungsanleitung

Fagor

Fagor 3FIS-844 Bedienungsanleitung

Fagor

Fagor FIC-37L Bedienungsanleitung

Fagor

Fagor Combi BI60 Bedienungsanleitung

Fagor

Fagor 3FFK-6836X Bedienungsanleitung

Fagor

Fagor FFJ1520 Bedienungsanleitung

Fagor

Fagor 1FFC-41 Bedienungsanleitung

Fagor

Fagor 3FFK-6644X Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung