F&F WN-723S Bedienungsanleitung

Inhaltsverzeichnis

Andere F&F Messgerät Handbücher

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

- 1 -

WN-723S

Voltage indicator,

3-phase

F&F Filipowski L.P.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: [email protected]om.pl

Do not dispose of this device in the trash along with other waste! According

to the Law on Waste, electro coming from households free of charge and

can give any amount to up to that end point of collec� on, as well as to sto-

re the occasion of the purchase of new equipment (in accordance with the

principle of old-for-new, regardless of brand). Electro thrown in the trash or

abandoned in nature, pose a threat to the environment and human health.

The WN-723S voltage indicator is designed for continuous me-

asurement and optical visualization of the voltage value in a

three-phase network. Blanks the screen when idle. The indicator

is activated by a touch button.

The indicated voltage range is 180÷270 V with a reading accura-

cy of 10 V. The switched on LED light indicates the voltage value

described on its height. The voltage value between 190 V and

260 V is indicated by the green LEDs. The extreme values 180 V

and 270 V are indicated by a red LED. Voltage lower than 180 V

is indicated by the 180 V red LED flashing. Voltage higher than

270 V is indicated by the flashing of the diode located at the

top, or in the case of operation in "bar" mode – flashing of the

entire bargraph.

The device can operate in "bar" or "single diode" mode. The se-

lection is made by shorting (or not) terminals 7-8.

When the power is turned on, the voltage value is displayed for

Purpose

Functioning

a period of 10 seconds, and then the LEDs go out. To display the

value again, you need to touch the front of the device with your

finger at the marked point.

"Bar" mode,

connection "without jumper"

"Single diode" mode,

connection "with jumper"

Voltage value

is shown for 10 seconds,

when you touch the market point

on the front of the housing

Operating modes

Triggering indication

- 3 -

1.Disconnect the power supply.

2.Install the indicator on the rail in the distribution board.

3.Connect the power wires according to the diagram.

4.Select the device mode (terminals 7-8).

5.Switch on the power supply and verify that the device is wor-

king correctly.

Mounting

Wiring diagram

- 4 -

power supply 3×230 V+N

voltage indicator 3× (10×LED)

indication range 180÷270 V

working mode bar mode or single diode mode

measurement error <2%

reading accuracy 10 V

time of displaying the value after triggering 10 s

power consumption <1 W

working temperature -25÷50°C

terminal 2.5 mm² screw terminals (cord)

4.0 mm² screw terminals (wire)

tightening torque 0.5 Nm

dimensions 2 modules (35 mm)

mounting on TH-35 rail

ingress protection IP20

F&F products are covered by a 24-month warranty from the date

of purchase. The warranty is only valid with proof of purchase.

Contact your dealer or contact us directly.

F&F Filipowski L.P. declares that the device is in conformity

with the essential requirements of The Low Voltage Directive

(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)

Directive 2014/30/UE.

The CE Declaration of Conformity, along with the references to

the standards in relation to which conformity is declared, can be

found www.fif.com.pl on the product subpage.

Technical data

Warranty

CE declaration

E230816