Fantec SQ-35RU3e Bedienungsanleitung
Fantec SQ-35RU3e
4 x 3.5" SATA, HDD, RAID, USB3.0, eSATA
User Manual
Important:
All data is deleted when changing the RAID mode.
Backup the HDD(s) before changing the RAID mode.
Fantec SQ-35RU3e User Manual
1
1. Package Contents
- 1 x user manual
- 1x 4 bay hard drive enclosure
- 4x HDD bays
- 8 x screws
- 1 x USB 3.0 cable
- 1 x eSATA cable
- 1 x power adaptor
2. Notes
-eSATA and USB 3.0 connector (downwards compatible with USB2.0 and USB1.1)
-Auto energy saving function when PC is switched off
-25% less power consumption with Green Power Design
-33%less HDD temperature with 80mm fan and intelligent ventilation design
-Up to 5Gbps transmission speed per USB3.0 connection
-SATA-II interface: supports HDDs with SATA I, II, III
-4 HDDs, Plug&Play, hot swap
-Supports HDD capacity up to 4TB in GPT format, Windows 7/Vista
-Windows XP (MBR) supports HDD/Raid drives up to 2TB (4x500GB)!
Please note:
1. Read this user manual carefully before installing and using the product.
2. This product works in temperatures between 0oC and 40oC and in relative humidity
between 0% and 80%. Ensure a well ventilated working environment.
3. Do not block the ventilation openings to allow heat dissipation.
4. Do not place any liquids or chemicals on the device.
5. The power adaptor works with 12V, 5.4A, input 100V~240V. Do not connect any other
power supply to avoid damaging the device.
6. Do not cover the power adaptor and ensure sufficient ventilation.
7. The HDD must be properly attached in the HDD insert before being inserted in the
housing.
Fantec SQ-35RU3e User Manual
2
3. About the device
Hardware overview
DC input
Connector for supplied power adaptor
- 12VDC, 100-240VAC, 50-60Hz
PC connection
USB 3.0
Connect USB3.0 cable to computer
eSATA
Connect eSATA cable to computer
Note: In case of concurrent connection of eSATA and USB3.0 the PC detects eSATA.
Fan speed control
Controller
Use the controller to set the fan speed
LED indicators:
Power LED
Green
LIGHTS UP: switched on
OFF: switched off
HDD 1
Blue
LIGHTS UP: HDD connected
FLASHES: access (read/write)
FLASHES CONTINUOUSLY (3Hz): HDD fault
OFF: HDD not installed/removed/sleep mode
HDD 2
Blue
LIGHTS UP: HDD connected
FLASHES: access (read/write)
FLASHES CONTINUOUSLY (3Hz): HDD fault
OFF: HDD not installed/removed/sleep mode
HDD 3
Blue
LIGHTS UP: HDD connected
FLASHES: access (read/write)
FLASHES CONTINUOUSLY (3Hz): HDD fault
OFF: HDD not installed/removed/sleep mode
HDD 4
Blue
LIGHTS UP: HDD connected
FLASHES: access (read/write)
FLASHES CONTINUOUSLY (3Hz): HDD fault
OFF: HDD not installed/removed/sleep mode
Fantec SQ-35RU3e User Manual
3
Front / Rear view
Power LED
HDD1 LED
HDD2 LED
HDD3 LED
HDD4 LED
Fantec SQ-35RU3e User Manual
4
4. Hardware installation instructions
Step1: Push the Locker switch to the left side to unlock the HDD tray.
Step2: Take out the HDD trays.
Fantec SQ-35RU3e User Manual
5
Step3: Gluing the rubber pad to the middle at inner side of HDD tray if your HDD is a little
shorter.
Step4: Install the HDD into the tray and insert one screw on each side. Make sure screws are
firmly tightened, holding the tray and HDD together.
Fantec SQ-35RU3e User Manual
6
Step5: Slide HDD trays into the case.
Step6: Push the switch to the right side to lock the HDD tray.
Fantec SQ-35RU3e User Manual
7
5. RAID settings
With FANTEC SQ-35RU3e you can set the Raid versions described below. The SQ-35RU3e creates
from 4 physical drives one virtual drive. This is managed by the Raid housing. The virtual drive is
displayed as a “volume”on a Windows computer. Thanks to the virtual drive you can create a Raid
with the FANTEC SQ-35RU3e even with different HDD models. The HDDs may have both different
capacities and use different speeds.
RAID mode settings
Fantec SQ-35RU3e User Manual
8
Important: Backup the HDD(s) before changing the RAID setting.
1. Switch on the device.
2. Ensure that the desired number of HDDs is installed and that the respective HDD LEDs light up.
3. Connect the device via USB or eSATA cable to the PC.
4. Select the Raid mode by setting the “RAID switch” on the rear of the device.
5. Press and hold “RAID Reset”for 3~5 seconds to reset the HDD mode and to set the new mode.
6. Format the HDDs.
Note: Below you will find a detailed instruction for HDD formatting.
JBOD MODE (single):
JBOD mode displays each drive individually.
After connecting the device via USB or eSATA all drives are displayed.
Fantec SQ-35RU3e User Manual
9
BIG MODE (spanning):
BIG mode combines individual HDDs to a large drive and therefore seamlessly enlarges the
HDD capacity limitations as they apply for separately connected HDDs. With the BIG mode
you get maximum storage capacity without replacing existing HDDs with expensive new and
larger ones.
Note: It is not possible to subsequently add further data media or to remove individual drives
from Big, in both cases Raid would be inconsistent and your data are lost!
Inhaltsverzeichnis
Andere Fantec Gehäuse Handbücher
Fantec
Fantec MR-SA1041 Bedienungsanleitung
Fantec
Fantec QB-35US3R+AES Bedienungsanleitung
Fantec
Fantec DB-ALU3e Bedienungsanleitung
Fantec
Fantec QB-35US3R Bedienungsanleitung
Fantec
Fantec DB-F8U3e Bedienungsanleitung
Fantec
Fantec QB-X2U31R Bedienungsanleitung
Fantec
Fantec DB-ALU2 Bedienungsanleitung
Fantec
Fantec QB-35US3R+AES Bedienungsanleitung
Fantec
Fantec MR-25D Bedienungsanleitung
Fantec
Fantec MR-35VU3R Bedienungsanleitung
Fantec
Fantec NVMe31-FastLock Bedienungsanleitung
Fantec
Fantec DB-ALU3e Bedienungsanleitung
Fantec
Fantec DB-ALU3 Bedienungsanleitung
Fantec
Fantec QB-35U31R Bedienungsanleitung
Fantec
Fantec AluPro U3 Bedienungsanleitung
Fantec
Fantec MB-X10U31 Bedienungsanleitung
Fantec
Fantec ER-35U3-6G Bedienungsanleitung
Fantec
Fantec mobiRAID X2 Bedienungsanleitung
Fantec
Fantec QB-X8US3-6G Bedienungsanleitung
Fantec
Fantec MB-X5U31H Bedienungsanleitung
