Fanvil X6U Bedienungsanleitung

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction

■

2 Requirements

■

2.1 Identifying Phone Model

■

2.2 Phone Firmware

■

2.3 DHCP Server

■

2.4 PBXware Version

■

3 Installation

■

3.1 Power Adapter

■

3.2 Power over Ethernet (PoE)

■

3.3 Find the Phone's IP Address

■

3.4 Reset to factory settings

■

4 Registering Phone

■

4.1 Manual Configuration

■

4.2 Registering a Phone

■

4.3 Auto Provisioning

■

5 Configure BLF

■

5.1 Extension Settings

■

5.2 Phone Settings

■

Introduction

This Configuration Guide is written as a general guide on how to configure the Fanvil phone

model X6U to work with PBXware 6.5.

Requirements

Identifying Phone Model

To start and successfully complete the registration of the Fanvil phone, users need to know

which phone model to set up.

On the back of each Fanvil phone, there is model information that you should check. Although

various phone models can have exactly the same requirements and installation procedures, they

can also have significantly different requirements and installation procedures, so that is why it

is important to know the model you own which results in you setting up the device successfully.

Phone Firmware

Make sure that the phone is loaded with an appropriate firmware version, 2.4.5.

■

To find out the firmware version of the Fanvil phone model, open a new browser window and

■

enter the phone's IP address in order to access the phone's web administration interface login

screen. Example: http://192.168.1.22.

■

that factory default login details are as follows: username is admin and password is admin.

DHCP Server

Fully configured and operational DHCP server.

PBXware Version

PBXware version 6.5

In order to find out the PBXware version:

■

Navigate to Settings: About.

■

On the top of About page, you may see a code similar to this one PBXware Edition: Multi-

Tenant Release: 6.5.0.0 (41a4f0e6) Running: 16.16.1-gc-c0d40968, Proxy v6.5.0

(231c5f3), API: 6, libmemcached version: 1.0.18, where Release denotes the current

version of your PBXware.

Installation

This section describes how to install and connect the phone to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

Power Adapter

■

Power over Ethernet (PoE)

■

Factory Settings

■

Power Adapter

Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the phone and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the Ethernet cable between the Internet port on the phone and the network port on a

■

router or switch to access LAN.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Power over Ethernet (PoE)

Connect the Network (only)

Using a regular Ethernet cable, your phone can be powered from a Power over Ethernet (PoE)

compliant router or switch.

Connect the Ethernet cable between the Internet port on the phone and an available port on

■

the in-line power router or switch.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Find the Phone's IP Address

Press the OK key

■

Go to Status and press OK

■

The IP address will be shown on the display.

Reset to factory settings

This step is not required for brand new out-of-the-box phones, however, if the phone has been

already used then it is a must.

Open a new browser window and enter the phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22.

■

note that factory default login details are as follows: username is admin and password is

admin.

Click the Configurations tab.

■

Click on Reset Phone

■

Click the Reset button in order to reset the phone to factory settings. The phone will reset to

■

the factory settings and reboot.

Wait some time for a device to reboot.

■

NOTE: Do not unplug or remove power to the phone while it is updating firmware and

configuration.

Registering Phone

This section describes how to register the phone using manual configuration or auto

provisioning.

The following topics are covered:

Manual Configuration

■

Auto Provisioning

■

Manual Configuration

This section describes how to set UAD settings, create a PBXware Extension, and register a

phone.

The following topics are covered:

UAD Settings

■

Creating an Extension

■

Registering a Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

UAD Settings

Navigate to Settings:UAD.

■

Make sure Fanvil UAD is enabled. To check the UAD status, click the Edit icon corresponding

■

to the Fanvil phone.

Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.

■

Click Save.

■

Creating an Extension

Creating Extension

Add an Extension

Navigate to Extensions

■

Click Add Extension.

■

The standard options window will be shown below.

■

Select a Fanvil phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet, etc.

Click the Next step button.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Department

■

Department to which Extension belongs to. Example: Sales.

Click Save.

■

Registering a Phone

This section describes how to register a Fanvil phone using Hostname or IP Address.

Hostname or IP Address

Open a new browser window and enter the phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22

■

note that factory default login details are as follows: username is admin and password is

admin.

Click Line in the left-hand navigation menu.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Username

■

PBXware Extension number. Example: 1003

Authentication Name

■

Usually the same number as the Phone Number.

Authentication Password

■

The Secret of the Extension as received in the e-mail associated with this Extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

Extension.

Activate

■

Make sure the Activate check box is selected.

SIP Proxy Server Address

■

Enter the Hostname or IP Address of PBXware.

- Example of a Hostname: voip.bicomsystems.com

- Example of an IP Address: 192.168.1.10

Click Apply.

■

If everything is done as described above, you should have successfully registered your phone

■

to PBXware.

Dial *123 to verify the registration.

Auto Provisioning

This section describes how to set UAD settings, create a PBXware Extension and register the

phone using DHCP or Static IP address.

The following topics are covered:

UAD Settings

■

Creating an Extension

■

Registering a Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

UAD Settings

Navigate to Settings: UAD.

■

Make sure Fanvil UAD is enabled. To check the UAD status, click the Edit icon corresponding

■

to the Fanvil phone.

Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.

■

Click Save.

■

Creating an Extension

Creating Extension

Enable Auto provisioning

Add an Extension

Navigate to Extensions. Click Add Extension.

■

The standard options window will be shown below.

■

Select a Fanvil phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet etc.

Click Next step.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter the Fanvil phone's MAC address. Example: 0C383E123456. The MAC address can

be found on the back of the phone.

Click Save.

■

Registering Phone

This section describes how to register a Fanvil phone using TFTP & HTTP.

TFTP & HTTP

Open a new browser window and enter the phone's IP address, e.g. http://192.168.1.22.

■

Enter username and password and press the Confirm button. NOTE: The factory default

■

Click Auto Provision in the navigation tab.

■

Enter the Auto Provisioning username and password into the Authentication Name and

■

Authentication Password fields.

Make sure the Save Auto Provision Information check box is selected.

Make sure the Download CommonConfig enabled check box is NOT selected.

Click Static Provisioning Server

■

Choose what Protocol Type you intend to use: HTTP, HTTPS or Trivial FTP. NOTE: Our

■

recommendation is to use HTTP.

If you choose to use Protocol Type HTTP, enter http:// followed by Hostname or

IP Address, then followed by /prov.

Example of a Hostname using HTTP: http://abc.bicomsystems.com/prov

Example of an IP Address using HTTP: http://192.168.1.10/prov

If you choose to use Protocol Type TFTP, enter tftp:// followed by Hostname or

IP Address

Example of a Hostname: tftp://voip.bicomsystems.com

Example of an IP Address: tftp://192.168.1.10

Make sure the Update Mode is set to Update After Reboot.

■

Click Apply.

■

Click Tools in the navigation tab.

■

Click Reboot.

■

A pop-up window will show up, click OK to confirm the action.

■

You will have to wait for a couple of seconds for the configuration to be updated. NOTE: Do

■

not power off the phone.

The auto-provisioning process will start during the phone's reboot process. the phone will pick

■

up the appropriate configuration file from PBXware. If everything is done as described above,

you should have successfully registered your phone to PBXware.

Dial *123 to verify the registration.

Configure BLF

Extension Settings

This section describes how to configure BLF (Busy Lamp Field) for Fanvil X6U.

Open a new browser window and enter the IP address in order to access the PBXware's web

■

Andere Handbücher für X6U

Inhaltsverzeichnis

Andere Fanvil IP-Telefon Handbücher

Fanvil

Fanvil VH05 Bedienungsanleitung

Fanvil

Fanvil X3S Basic Bedienungsanleitung

Fanvil

Fanvil X303W Bedienungsanleitung

Fanvil

Fanvil D800 Bedienungsanleitung

Fanvil

Fanvil X7C Bedienungsanleitung

Fanvil

Fanvil X210i Bedienungsanleitung

Fanvil

Fanvil C62 Bedienungsanleitung

Fanvil

Fanvil X7A Bedienungsanleitung

Fanvil

Fanvil C56 Bedienungsanleitung

Fanvil

Fanvil X6 Bedienungsanleitung

Fanvil

Fanvil V64 Bedienungsanleitung

Fanvil

Fanvil H2S Bedienungsanleitung

Fanvil

Fanvil C62 Bedienungsanleitung

Fanvil

Fanvil F52 Bedienungsanleitung

Fanvil

Fanvil X210 Bedienungsanleitung

Fanvil

Fanvil C66 Bedienungsanleitung

Fanvil

Fanvil X4G Bedienungsanleitung

Fanvil

Fanvil X3SP Bedienungsanleitung

Fanvil

Fanvil BW530 Bedienungsanleitung

Fanvil

Fanvil X2P Bedienungsanleitung

Fanvil

Fanvil C600 Bedienungsanleitung

Fanvil

Fanvil X3U Bedienungsanleitung

Fanvil

Fanvil X2CP Bedienungsanleitung

Fanvil

Fanvil V67 Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung

Nortel

Nortel i2050 Bedienungsanleitung