Favero ASSIOMA PRO MX Bedienungsanleitung
ASSIOMA PRO MX
USER
MANUAL
EN
2
ENGLISH - USER MANUAL
Table of contents
Overview 3
Models 3
Package content 3
Product description 4
How to distinguish the left pedal from the right one 5
Warnings 5
Bike category 6
Installation 6
Installation of the cleats 10
Release force adjustment 11
Turn on 12
Activation 13
Pairing to your training device 13
Crank-arm length 15
Manual and automatic calibration 15
First use 17
Battery charge 17
From single to dual-sided 19
Pedals removal 19
Reinstalling the pedals (swap them between bikes) 20
Sensors’ LEDs behaviour 20
Servicing 20
Spare parts 22
Stack height 23
Technical features 23
Favero Electronics 25
Warranty 25
Copyright 25
3
1. Overview
To use the product it’s necessary to install the Favero
Assioma app, which is available for free on the App Store
and Google Play Store.
When using the product for the rst time, you can nd on
the app an interactive quick start guide with all the steps
necessary for the installation.
Nevertheless, we invite you to read this manual carefully
for the correct use of Assioma PRO MX.
2. Models
ASSIOMA PRO MX-2 Art. 773-10-02
Left and right MTB pedals with power sensors on both
sides.
ASSIOMA PRO MX-1 Art. 773-10-01
Left MTB pedal with power sensor.
Right MTB pedal without power sensor.
3. Package content
GUARANTEE AND
SAFETY MANUALS
Top tray
Bottom box
WELCOME
FLYER
Fig. 1
ASSIOMA PRO MX-1
Power meter with sensor on the left
side only (773-10-01)
1 Micro USB 2-way charging cable
1 Magnetic connector
MTB-compatible SPD® cleats
4 Washers
Greasing tools kit
Guarantee and safety manual
Welcome yer
ASSIOMA PRO MX-2
Power meter with sensors on both
sides (773-10-02)
1 Micro USB 2-way charging cable
2 Magnetic connectors
MTB-compatible SPD® cleats
4 Washers
Greasing tools kit
Guarantee and safety manual
Welcome yer
4
4. Product description
Assioma PRO MX is a clip-less pedal with a sensor
measuring the force applied to the pedal during the
pedal stroke.
Assioma PRO MX is designed to be used in the following
disciplines:
• Mountain Bike (MTB)
• Gravel (GR)
• Ciclocross (CX)
• Cross Country (XC)
It includes the function of cadence meter and calculates
in real time the power output during a pedal stroke to
transmit it to the bike computer or app it is paired with.
It is equipped with a rechargeable battery designed to
guarantee an operating time of at least 60 hours.
Assioma PRO MX is resistant to water, mud and dust
ingress (IP67) due to the housing of all the electronic parts
and the rechargeable battery inside its spindle.
Assioma PRO MX features both ANT+ and Bluetooth
technologies to interact and transmit data to external
devices.
Fig. 2
Sensor housed inside the axle
Led signal
Pins for charging the battery
5
5. How to distinguish the left pedal from the
right one
Left pedal and spindle
• The left pedal is stamped “L” on one internal side of the
clipless system
• The left spindle is marked with a round groove close to
the threads.
Right pedal and spindle
• The right pedal is stamped “R” on one internal side of
the clipless system
• The right spindle, unlike the left one, has no round
groove close to the threads.
6. Warnings
Carefully read the following user manual and the
guarantee and safety manual provided within the box
before installing the product.
A wrong installation and improper use of the product
can cause accidents.
If you have any doubts about your ability to install the
product, we recommend you to ask for the assistance
of a specialized mechanic.
Before start riding, make sure that the force necessary
to release your shoe from the pedal is suited to your
needs.
Fig. 3
Round groove on
the left axle
No round groove
on the right axle
6
7. Bike category
Assioma PRO MX has been designed for paths up to
category 3 (standard ASTM F2043).
It meets the safety standard DIN EN ISO 4210.
8. Installation
ASSIOMA PRO MX uses needle roller bearings, which offer
a much higher load carrying capacity compared to the
standard ball bearings.
Some cyclists more sensitive to the feeling with their bike
may, however, note a small play in their pedals, which is to
be considered as completely normal with the use of such
bearings.
1. Thread greasing
Apply a thin layer of lithium grease
to the spindle thread to ease
potential future removals.
2. Check the distance between pedal and bike chain and
pedal and frame
For the correct installation of the product, it’s important
to have enough space between spindle cap and bike chain
and spindle cap and frame.
Riding on rough
terrain with drops
of less than 61 cm.
3
ASTM F2043
Fig. 4
7
Proceed as described:
1. Screw the spindle into the crank-arm MANUALLY until
complete insertion.
See Fig. 5
Left pedal (L) counter-clockwise
Right pedal (R) clockwise
Fig. 5
Carry out this operation
MANUALLY, without any
tools.
8
2. Make sure to shift the
chain to the largest,
outermost chainring
and the smallest
cassette sprocket.
See Fig. 6
3. Check the distances to avoid any kind of interference
• When stationary, rotate the crank-arm manually until
performing a complete rotation
• The spindle cap must be at a distance bigger than
4mm both from the bike chain and the frame
• If you use crank boots, make sure they don’t interfere
with the bike chain or rear triangle.
See Fig. 7.
Fig. 6
>4mm >4mm
Fig. 7
9
If the distance is inferior
to 4mm, use one or two
washers (A1, A2).
Use only the washers
provided by Favero
Electronics.
See Fig. 8.
3. Tightening on the crank-arm
Finish tightening with a
torque wrench by applying a
force of 30-40Nm.
Turn counter-clockwise for
the left pedal (L), clockwise
for the right (R).
Make sure the pedal is correctly tightened before use.
Read carefully the information in the guarantee and
security manual provided within the box.
A1
A2
Fig. 8
Fig. 9
30-40Nm
15
Use a 15mm-open-end
wrench.
Don’t use spanners or
adjustable wrenches.
10
9. Installation of the cleats
Use only the cleats provided (SPD®
compatibile) or the original Shimano® SM-
SH51 cleats.
Align the cleats properly according to your
needs and tighten the mounting bolts with
a torque of 4-6Nm.
The use of other types of cleats might not be suitable,
cause potential damage to the product and void the
warranty.
To x the cleats, use the mounting bolts provided with
them.
Tightening torque: 4-6 Nm
Regularly check the status of the cleats
• Check that the holes where the mounting bolts are
screwed in are not damaged/worn out
• Check that the cleats are well tightened to the shoes.
Carefully read the information contained in the
guarantee and safety manual.
Front
A
B
C
4
Mounting bolts
Cleat adapter
Cleat
Fig. 10
Inhaltsverzeichnis
Beliebte Fahrradzubehör Handbücher anderer Marken
Sigma
Sigma BC 16.16 Bedienungsanleitung
Playcore
Playcore Dero Setbacks Bedienungsanleitung
VDO Cyclecomputing
VDO Cyclecomputing x3dw Bedienungsanleitung
Cateye
Cateye RAPID X2 Bedienungsanleitung
buratti meccanica
buratti meccanica Clorofilla Trail Bedienungsanleitung
Shimano
Shimano SG-8R20 Betriebsanleitung
