Federal Signal Corporation DTX Series Bedienungsanleitung

Safety Messages to Installers of Federal Signal Products

People’s lives depend on your proper installation and servicing of our products. It is important to

read and follow all instructions shipped with this product. In addition, listed below are some other

important safety instructions and precautions you should follow:

• To properly install a vehicular camera system and options, you must have a good

understanding of automotive electrical systems along with proﬁciency in the installation

and use of safety warning equipment.

• Read and follow all safety and operating instructions before installing, conguring, or

operating the entire DTX Series system. Safety and operating instructions are also located

in the DTX Series software interface and can be accessed by clicking the Help button.

• DO NOT install equipment or route wiring in the deployment path of an airbag.

• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat

needs to be recalibrated for proper airbag deployment.

• When drilling into a vehicle structure, be sure that both sides of the surface are clear of

anything that could be damaged. Remove all burrs from drilled holes. To prevent electrical

shorts, grommet all drilled holes through which wiring passes. Also ensure that the mounting

screws do not cause electrical or mechanical damage to the vehicle.

• You should frequently inspect the DTX Series System to ensure that it is operating properly

and that it is securely attached the vehicle.

• File these instructions in a safe place and refer to them when maintaining or reinstalling the

product.

Failure to follow all safety precautions and instructions may result in property damage, serious

injury, or death.

Product Overview

The Model DTX-CSM Front Camera Suction Mount (FSC Part No. 8605238) is a mounting

option with a powerful suction cup for attaching the DTX-FC front camera to the front windshield.

When used in place of the standard permanent-mount adhesive kit, it allows the camera to be

easily repositioned on the windshield. The dual pivot vertical/horizontal mount provides exible

viewports and comes preassembled, making the camera installation quick and easy.

Required Tools

• Glass cleaner

• Towel

• Phillips screwdriver

2562588A REV. A 1010

Installation Instructions for the Model DTX-CSM Front Camera

Suction Mount for the Model DTX-FC Front Camera

DTX Series Installation Instructions

2Model DTX-CSM Front Camera Suction Mount

Required Hardware

• #10-32 Phillips screw (included)

Installing the DTX-CSM Universal Mount

To install the camera to the front windshield with the DTX-CSM option:

Step 1: Locate a surface on the front windshield to mount the DTX-CSM assembly. Clean the

surface with a glass cleaner and towel.

Step 2: Place the camera on the mounting bracket and align the hole on the bracket with the

hole on the bottom of camera (Figure 1 on page 2).

Step 3: Insert the supplied #10-32 screw into the hole in the bracket and tighten the screw.

Step 4: Note the word PRESS on the push button of the suction cup and the C-shaped lever

circling it. Orient the suction cup as shown in Figure 1 and adhere the cup to the

mounting surface by pressing the button.

Step 5: To maintain suction, rotate the C-shaped lever 90 degrees to position it above the word

PRESS on the push button.

Aiming the DTX-RC Camera

To aim and steady the camera:

Step 1: Loosen the rear knob, pivot the camera right or left, and tighten the knob (Figure 1).

Step 2: Adjust the two side knobs so that the camera remains level and is at least 1/2 inch

from the windshield. Ensure that it does not interfere with the operation of the vehicle.

Connecting the Camera Cable

To connect the camera to the DTX system:

Step 1: Connect the end of the front camera cable to the white connector of DTX-RC camera

extension cable.

Step 2: Route and connect the extension cable to the white connector of the DTX-CC

peripherals cable from the DTX-2-DVR. Ensure that the cables do not interfere with the

operation of any equipment or hinder the activities of the driver and passenger.

Step 3: Test the connection to the DTX-2-DVR to ensure the camera cable connection is

working properly.

DTX Series Installation Instructions

Model DTX-CSM Front Camera Suction Mount

Figure 1 DTX-CSM Front Camera Suction Mount

290A6591

#10-32 SCREW (SUPPLIED)

SIDE KNOBS FOR

VERTICAL AND

FORWARD/BACKWARD

ADJUSTMENT

MOUNTING BRACKET

SUCTION CUP PUSH BUTTON

C-SHAPED LEVER

ORIENTATION OF SUCTION

CUP AGAINST WINDSHIELD

SUCTION CUP

REAR KNOB FOR

RIGHT/LEFT ADJUSTMENT

TO EXTENSION CABLE

PRESS PUSH BUTTON.

MOVE LEVER OVER

PUSH BUTTON TO

MAINTAIN SUCTION.

DTX-FC CAMERA

DTX Series Installation Instructions

4Model DTX-CSM Front Camera Suction Mount

Obtaining Technical Support and Service

If a DTX Series system device does not operate properly and falls within the warranty coverage

provided, or if servicing assistance is needed, contact technical support at:

Federal Signal Corporation

2645 Federal Signal Drive

University Park, IL 60484-3167

Phone: (800) 433-9132

empserviceinf[email protected]

Returning a Product to Federal Signal

Before returning a product to Federal Signal, call 800-264-3578, 800-433-9132, or

800-824-0254 to obtain a Returned Merchandise Authorization number (RMA number).

To expedite the process please be prepared with the following information:

• Your Federal Signal customer or account number.

• The purchase order number under which the items were purchased.

• The shipping method.

• The model or part number of the product being returned.

• The quantity of products being returned.

• Drop ship information as needed.

• Any estimate required.

When you receive your RMA Number:

• Write the RMA number on the outside of the box of returned items.

• Reference the RMA number on your paperwork inside of the box.

• Write the RMA number down, so that you can easily check on status of the returned

equipment.

Send all material with the issued RMA Number to:

Federal Signal Corporation

Public Safety Systems

2645 Federal Signal Drive

University Park, IL 60484-3167

Attn: Service Department

RMA: #__________

800-433-9132

800-343-9706 (fax)

www.fedsig.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Rack & Stand Handbücher

Federal Signal Corporation

Federal Signal Corporation CUDA TRIOPTIC 350201-06 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DTX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation LWMB2 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation HotFoot Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MPSM6-LPV2 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Valor Hook-On Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation RB-CAP11 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IPX-ROW1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Valor Low-Profile Hook Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IPX-GRL5 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IPX-PBL1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IPX-PB45H Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation C Series Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung