Federal Signal Corporation GEN-IIB/C Bedienungsanleitung

Description, Installation, and User Manual

Non-Metallic Zone 1 Loudspeaker

Models: GEN-IIB/C and GEN-IIB/C-ISMT

25500655

Rev. A1 0123

Printed in U.S.A.

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of tness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Technical Support 800-524-3021

All product names or trademarks are properties of their respective owners.

Description, Installation, and User Manual

Federal Signal www.fedsig.com

Contents

1.0 Safety Messages................................................................................................................................................4

1.1 Safety Messages to Installers.................................................................................................................4

2.0 General Description ..........................................................................................................................................7

2.1 Introduction.............................................................................................................................................7

2.2 Overview.................................................................................................................................................7

2.3 Features .................................................................................................................................................7

2.4 Unpacking the Loudspeaker...................................................................................................................8

2.5 Ordering Information...............................................................................................................................8

2.6 Certications...........................................................................................................................................8

3.0 Specications ....................................................................................................................................................9

4.0 Specic Conditions for Use..............................................................................................................................9

5.0 Mounting the Loudspeaker.............................................................................................................................10

6.0 Adjusting the Vertical Angle ........................................................................................................................... 11

7.0 Wiring the Loudspeaker.................................................................................................................................. 11

8.0 Setting Transformer Wattage Taps ................................................................................................................13

9.0 Completing the Installation ............................................................................................................................13

10.0 Periodically Inspecting the Loudspeaker....................................................................................................13

11.0 Servicing the Loudspeaker...........................................................................................................................14

12.0 Ordering Replacement Parts........................................................................................................................14

13.0 Getting Service ..............................................................................................................................................15

Tables

Table 1 Ordering Information .................................................................................................................................8

Table 2 Accessories ................................................................................................................................................8

Table 3 Specications .............................................................................................................................................9

Table 4 Wattage tap settings ................................................................................................................................13

Table 5 Replacement parts ...................................................................................................................................14

Figures

Figure 1 Loudspeaker dimensions ...................................................................................................................... 11

Figure 2 Loudspeaker connections for GEN-IIB and GEN-IIC...........................................................................12

Figure 3 Loudspeaker connections for GEN-IIB-ISMT and GEN-IIC-ISMT.......................................................12

Safety Messages

Non-Metallic Zone 1 Loudspeaker (GEN-IIB/C and GEN-IIB/C-ISMT)

Federal Signal www.fedsig.com

1.0 Safety Messages

It is important to follow all instructions shipped with this product. This device is to be

installed by trained personnel who are thoroughly familiar with the country’s electric

codes and will follow these guidelines as well as local codes and ordinances, including

any state or local noise-control ordinances.

Planning

• If suitable warning equipment is not selected, the installation site for the system is

not selected properly, or the system is not installed properly, it may not produce the

intended optimum audible warning. Follow the Federal Emergency Management

Agency (FEMA) recommendations.

• If the system is not activated in a timely manner when an emergency condition exists,

it cannot provide the intended audible warning. It is imperative that knowledgeable

people, who are provided with the necessary information, be available at all times to

authorize activation.

• The sound output of the system is capable of causing permanent hearing damage.

To prevent excessive exposure, carefully plan placement, post warnings, and restrict

access to areas near loudspeakers. Review and comply with any local or state noise

control ordinances as well as OSHA noise exposure regulations and guidelines.

• Activating the system may not result in people taking the desired actions if those

to be warned are not properly trained about the meaning of warning sounds. Users

should follow FEMA recommendations and instruct those to be warned of correct

actions to be taken.

After installation, service, or maintenance, test the system to conﬁrm that it is operating

properly. Test the system regularly to conﬁrm that it will be operational in an emergency.

1.1 Safety Messages to Installers

People’s lives depend on your safe installation of our products. It is important to follow

all instructions shipped with this product. This device is to be installed by a trained

electrician who is thoroughly familiar with the National Electrical Code and/or Canadian

Electrical Code and will follow the NEC and/or CEC Guidelines as well as all local codes.

The selection of the mounting location for this system, its controls, and the routing of

the wiring are to be accomplished under the direction of the Facilities Engineer and

the Safety Engineer. Listed below are some other important safety instructions and

precautions you should follow:

• Disconnect the device from the power supply/audio source before any installation or

maintenance is performed.

• Do not open the loudspeaker enclosure when a hazardous atmosphere is present.

• To determine if the device can be used safely in the intended area, review the

Certiﬁcations section in this manual.

• Electrocution or severe personal injury can occur when performing various installation

and service functions such as making electrical connections, drilling holes, or lifting

equipment. Therefore, only experienced electricians should install this product in

Safety Messages

Description, Installation, and User Manual

Federal Signal www.fedsig.com

accordance with national, state, or province and any other electrical codes having

jurisdiction. Perform all work under the direction of the installation or service crew

safety foreman.

• Read and understand all instructions before installing, operating, or servicing this

equipment.

• All eective warning sounds may, in certain circumstances, cause permanent hearing

loss. Take appropriate precautions, such as wearing hearing protection. The maximum

sound level exposure limits speciﬁed in OSHA 29 CFR 1910 should not be exceeded.

• For optimum sound distribution, do not install the loudspeakers where objects would

block any portion of the front of the system.

• Establish a procedure to routinely check the signal system for proper activation and

operation.

• Any maintenance to the unit MUST be performed by a trained electrician in

accordance with NEC Guidelines and local codes or a Federal Signal certiﬁed Service

Provider.

• Never alter the unit in any manner.

• The nameplate should NOT be obscured, as it contains cautionary and/or other

information of importance to maintenance personnel.

• After installation and completion of the initial system test, provide a copy of these

instructions to all personnel responsible for the operation, periodic testing, and

maintenance of the equipment.

• File these instructions in a safe place and refer to them when maintaining and/or

reinstalling the device.

Failure to follow all safety precautions and instructions may result in property damage,

serious injury, or death.

Installation and Service

• After installation or service, test the system to conﬁrm that it is operating properly. Test

the system regularly to conﬁrm that it will be operational in an emergency.

• If future service and operating personnel do not have these instructions to refer to,

the system may not provide the intended audible warning, and service personnel

may be exposed to death, permanent hearing loss, or other bodily injuries. File

these instructions in a safe place and refer to them periodically. Give a copy of these

instructions to new recruits and trainees. Also give a copy to anyone who is going to

service or repair the system.

• To reduce the risk of electric shock, do not perform any servicing other than what

is contained in the operating instructions unless you are qualiﬁed to do so. Refer all

servicing to qualiﬁed service personnel. Always test the system before using after

repairs have been made.

• Concerning the potential electrostatic charging hazard, as mentioned in the certiﬁcate

“Speciﬁc Conditions of Use,” under normal conditions of use, these devices are for

ﬁxed installations and are not generally in contact with people. The risk of ignition

is low. In addition, maintenance, cleaning, and extreme environmental factors (for

example, high-velocity dust-laden atmospheres or high-pressure steam) should be

Safety Messages

Non-Metallic Zone 1 Loudspeaker (GEN-IIB/C and GEN-IIB/C-ISMT)

Federal Signal www.fedsig.com

taken into account by the end user, using local Explosive Atmosphere (Ex) Electrical

installations design, selection, inspection, and maintenance Codes and Standards.

POTENTIAL ELECTROSTATIC CHARGING HAZARD: If the unit requires cleaning,

ONLY clean the exterior with a water-dampened cloth to avoid electrostatic charge

buildup.

FIRE/EXPLOSION HAZARD: Do not open the loudspeaker when it is energized.

Failure to observe this warning could result in serious injury or death.

• Any maintenance to the loudspeaker must be done with the power turned o.

• After disconnecting power, allow ten minutes for the internal components to cool and

to allow all capacitors to discharge.

• Do not open the loudspeaker enclosure when a hazardous atmosphere is present.

• Use only service parts provided by the Federal Signal factory. Only these components

have been veriﬁed and certiﬁed for use in hazardous areas.

• Any repairs or modiﬁcations made to the encapsulated areas will invalidate the

certiﬁcation. Do not repair ﬂameproof joints.

• The nameplate, which contains cautionary or other information of importance to

maintenance personnel, should not be obscured.

Hazard Classiﬁcation

Federal Signal uses signal words to identify the following:

DANGER indicates a hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

NOTICE is used to address practices not related to physical injury.

Read and understand the information contained in this manual before

attempting to install or service the system.

General Description

Description, Installation, and User Manual

Federal Signal www.fedsig.com

2.0 General Description

2.1 Introduction

This document is a description, installation, and user manual for the GEN-IIB/C and

GEN-IIB/C-ISMT Series Non-Metallic Zone 1 Loudspeaker. Its intended audience are those

assigned to install, use, and maintain the loudspeakers.

2.2 Overview

The Federal Signal non-metallic loudspeakers, models GEN-IIB/C and GEN-IIB/C-ISMT,

are designed for use in industrial public address and general alarm applications where

corrosion resistance and ATEX/IEC Certiﬁcation are required.

• GEN-IIB/C and GEN IIB/C-ISMT are available in an ATEX/IEC Zone 1 explosion-proof

version certiﬁed IP66 for ingress of dust and combustible gas to GroupIIB + H2

(Hydrogen) or Group IIC. The speakers are manufactured from corrosion-resistant,

Glass Reinforced Polyester (GRP).

• GEN IIB/C-ISMT diers from the standard model GEN IIB/C in that it includes an

intelligent speaker monitoring tapping (ISMT) interface built into the speaker to allow

remote monitoring and tapping of the speaker without needing to physically access

the deployed speaker.

• GEN IIB/C and GEN IIB/C-ISMT loudspeakers are designed to accept an audio input of

100VRMS. Each speaker is a transformer coupled with a maximum output of 25W and

is supplied with preset taps (25, 15, 10, and 6) to adjust sound output.

Mounting is supplied by a “common template” stainless steel ratcheted mounting bracket

that locks the loudspeaker in position at a speciﬁc angle without slipping. The optional

swivel mounting bracket provides slotted mounting holes to further adjust speaker

position and adapt to a variety of dierent surfaces.

Connection for ﬁeld wiring is provided by two M20 x 1.5 mm threaded openings in the

speaker housing and terminated via internal terminal blocks. All external hardware is

manufactured from stainless steel to resist corrosion and provide serviceability for years

to come.

2.3 Features

The speaker has the following features:

• SPL: 123 +/-3 dBA at 25 W, 1 m

• 100 VRMS, 25 W audio input

• Re-entrant horn design

• Non-Metallic, Glass Reinforced Polyester (GRP), UV solar resistant housing

• U Mounting bracket included, optional swivel mount bracket available

• IP66 rated

• ATEX and IECEx Certiﬁed for Zone 1, Gas Group IIB+H2 or IIC

• Cable entry: 2 x M20 x 1.5 mm

General Description

Non-Metallic Zone 1 Loudspeaker (GEN-IIB/C and GEN-IIB/C-ISMT)

Federal Signal www.fedsig.com

2.4 Unpacking the Loudspeaker

After unpacking the loudspeaker, examine it for damage that may have occurred in transit.

If the loudspeaker has been damaged, do not attempt to install or operate it. File a claim

immediately with the carrier stating the extent of the damage. If you are missing any parts,

contact Federal Signal Customer Support. Carefully check all envelopes, shipping labels,

and tags before removing or destroying them.

2.5 Ordering Information

Table 1 Ordering Information

Part Numbers Description

GEN-IIB Corrosion Resistant Loudspeaker, ATEX Zone 1 Rated Gas Group

IIB+H2

GEN-IIB-ISMT Corrosion Resistant Loudspeaker, ATEX Zone 1 Rated Gas Group

IIB+H2

GEN-IIC Corrosion Resistant Loudspeaker, ATEX Zone 1 Rated Gas Group IIC

GEN-IIC-ISMT Corrosion Resistant Loudspeaker, ATEX Zone 1 Rated Gas Group IIC

Table 2 Accessories

Part Numbers Description

K8595172A Swivel Mounting Bracket

2.6 Certications

ATEX and IECEx Certiﬁed for Zone1, Gas Group, IIB+H2 or IIC

Certicate Numbers ATEX Certicate Number: UL 22 ATEX 2889X

IECEx Certicate Number: IECEx UL 22.0094X

ATEX coding II 2 G D

Protection

GEN-IIB and GEN-IIB-ISMT

GEN-IIC and GEN-IIC-ISMT

II 2 G Ex db IIB+H2 T4 Gb (Tamb = -50°C to +65°C)

II 2 D Ex tb IIIC T135C Db IP66

II 2 G Ex db IIC T4 Gb (Tamb = -50°C to +65°C)

II 2 D Ex tb IIIC T135°C Db IP66

Standards applied EN60079-0, EN60079-1, EN60079-31, IEC60079-0, IEC

60079-1, and IEC60079-31.

Refer to Certicate Numbers for specic standard versions.

Specications

Description, Installation, and User Manual

Federal Signal www.fedsig.com

3.0 Specications

Table 3 Specications

Electrical Audio Line Voltage 100 VRMS

Max rated power 25 W

Enclosure Rating IP66 Indoor/Outdoor Use

Gland Entry 2 x M20 x 1.5 mm

Cable Terminations 0.5 mm2to 4 mm2(20 AWG to 12 AWG)

Size (Height x Length) 232.2 x 347 mm (9.13 x 13.66 inches)

Material Glass Reinforced Polyester (GRP)

Color Black

Audio Input 100 VRMS

Max Audio Output 123 +/-3 dBA at 25 W (1 meter)

Net Weight 6.58 kg (14.5 lb)

Shipping Weight 7.48 kg (16.5 lb)

Ambient Environment T4: −50°C ≤ Ta ≤ +65°C

Max. Surface Temperature 135°C at +65°C ambient

4.0 Specic Conditions for Use

The specic conditions for use:

POTENTIAL ELECTROSTATIC CHARGING HAZARD/INSTALLATION PRECAUTIONS:

• The speaker housing has external non-metallic surfaces that may provide

an electrostatic charging hazard. Under normal conditions of use, these

devices are for ﬁxed installations and are not generally in contact with people.

The risk of ignition is low. In addition, maintenance, cleaning, and extreme

environmental factors (for example, high-velocity dust-laden atmospheres or

high-pressure steam) should be taken into account by the end user, using local

Explosive Atmosphere Ex Electrical installations design, selection, inspection,

and maintenance Codes and Standards.

• The equipment has a metallic mounting bracket that can store electrical

charge and may provide a potential electrostatic charging hazard. The metallic

mounting bracket has a capacitance of 11 pF.

• Due to the high ambient rating of the equipment and the internally generated

temperatures at the entries and branching point of the conductors, select

suitable cable, cable glands, and conductors with a minimum temperature

rating of 85°C.

• Replacement cover screws are not standard fasteners. They must be sourced

from the equipment manufacturer only. Do not repair ﬂameproof joints.

Mounting the Loudspeaker

Non-Metallic Zone 1 Loudspeaker (GEN-IIB/C and GEN-IIB/C-ISMT)

Federal Signal www.fedsig.com

• If the equipment contains an unused entry hole after installation, use only

suitable ATEX and IECEx Certiﬁed Ex “tb” (IP66) and Ex “db” (IIC gas) rated

components to seal the entry hole before operating. The manufacturer

recommends EATON/REDAPT, Part # PD-U Series stopping plugs.

• The equipment terminal block shall be used with conductor sizes of 0.5 mm2to

4 mm2. The protective earth ground connection conductor size shall equal the

conductor size of the audio input wires at the minimum.

5.0 Mounting the Loudspeaker

DRILLING PRECAUTIONS: When drilling holes, check the area you are drilling into

to ensure you do not damage anything while drilling. All drilled holes should be de-

burred, and all sharp edges should be smoothed.

The Models GEN-IIB/C loudspeakers are designed for mounting on a ﬂat horizontal or

vertical surface.

To mount the loudspeaker, obtain M6 stainless steel bolts, lockwashers, and ﬂat washers.

OBSTRUCTION HAZARD: The nameplate, which contains cautionary or other vital

information to maintenance personnel, should not be obscured.

To mount the loudspeaker:

1. Select a mounting location that is capable of supporting more than 7.5 kg (16.5 lb).

2. Use the mounting bracket as a template to scribe the centers of the mounting holes.

3. Drill an appropriately sized hole at each scribed mark for the mounting screws.

4. Mount the bracket with the installer-supplied bolts and washers.

5. Secure the loudspeaker to the mounting bracket.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Sprecher Handbücher

Federal Signal Corporation

Federal Signal Corporation MicroPulse MPS U Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IS-I-IP15X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MS100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SST3GCX-MV Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer15 I-IP15 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation A12SA Installations- und Benutzerhandbuch

Federal Signal Corporation

Federal Signal Corporation BP100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DS100X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation BP200-EF Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MS100-01 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SST3-MV Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer15 I-IP15 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IS-I-IP15 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global G-SPA-D Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation A12SA Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation UltraVoice RF100UX Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Informer15 I-IP15 Einrichtungshandbuch

Federal Signal Corporation

Federal Signal Corporation Global G-SPA Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DSA1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AM300X Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation ES100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Modulator MOD Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AMR6-2570K Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung