Federal Signal Corporation Informer15 I-IP15 Einrichtungshandbuch

Description, Specications, Installation,

Operation, and Service Manual

25500494

Rev. A0 0918

Printed in U.S.A.

Informer15™Speaker

Model I-IP15

IP-Enabled Indoor/Outdoor Speaker

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of tness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484-3167

www.fedsig.com

Customer Support 800-548-7229 • +1 708 534-3400

Technical Support 800-524-3021 • +1 708 534-3400

All other product names or trademarks are properties of their respective owners.

All products indicated are trademarks of Federal Signal Corporation.

Description, Specications, Installation, Operation, and Service Manual

Contents

Safety Messages......................................................................................................................................................5

Safety Messages to Installers .............................................................................................................................5

General Description ................................................................................................................................................8

Overview ............................................................................................................................................................8

Features..............................................................................................................................................................9

Ordering Information .........................................................................................................................................10

Specications ........................................................................................................................................................10

Installation.............................................................................................................................................................. 11

Flat Surface Mounting.......................................................................................................................................12

Opening the Housing ........................................................................................................................................13

Wiring to the Control Board...............................................................................................................................13

Closing the Housing..........................................................................................................................................15

Operations..............................................................................................................................................................16

Testing ....................................................................................................................................................................17

Maintenance...........................................................................................................................................................18

Ordering Replacement Parts ............................................................................................................................18

Getting Service ......................................................................................................................................................18

Figures

Figure 1 Depth and Height of Informer15 Speaker.............................................................................................12

Figure 2 I-IP15 Controller Board ..........................................................................................................................15

Informer15 Speaker (Model I-IP15)

Tables

Table 1 Ordering Information ...............................................................................................................................10

Table 2 Electrical Requirements ..........................................................................................................................10

Table 3 Environmental ..........................................................................................................................................10

Table 4 Physical..................................................................................................................................................... 11

Table 5 Connectors and Jacks for Control Board ..............................................................................................16

Table 6 Connectors and Jacks for Amplier.......................................................................................................16

Table 7 Visual Indications for Control Board......................................................................................................17

Table 8 Visual Indications for Amplier...............................................................................................................17

Table 9 Replacement Parts ...................................................................................................................................18

Safety Messages

Description, Specications, Installation, Operation, and Service Manual

Safety Messages

It is important to follow all instructions shipped with this product. This device is to be

installed by trained personnel who are thoroughly familiar with the country electric

codes and will follow these guidelines as well as local codes.

Planning

• If suitable warning equipment is not selected, the installation site for the Informer15

Speaker is not selected properly or the Informer15 Speaker is not installed properly,

it may not produce the intended optimum audible warning. Follow Federal

Emergency Management Agency (FEMA) recommendations.

• If Informer15 Speakers are not activated in a timely manner when an emergency

condition exists, they cannot provide the intended audible warning. It is imperative

that knowledgeable people, who are provided with the necessary information, are

available at all times to authorize activation.

• When Informer15 Speakers are used out of doors, people indoors may not be able to

hear the warning signals. Separate warning devices or procedures may be needed to

effectively warn people indoors.

• The sound output of Informer15 Speaker is capable of causing permanent hearing

damage. To prevent excessive exposure, carefully plan placement, post warnings, and

restrict access to areas near sirens.

• Activating the Informer15 Speaker may not result in people taking the desired

actions if those to be warned are not properly trained about the meaning of warning

sounds. Users should follow FEMA recommendations and instruct those to be

warned of correct actions to be taken.

After installation, service, or maintenance, test the system to conrm that it is operating

properly. Test the system regularly to conrm that it will be operational in an emergency.

Safety Messages to Installers

People’s lives depend on your safe installation of our products. It is important to follow

all instructions shipped with this product. This device is to be installed by a trained

electrician who is thoroughly familiar with the National Electrical Code and/or Canadian

Electrical Code and will follow the NEC and/or CEC Guidelines as well as all local

codes. This Informer15 Speaker should be considered a part of the warning system and

not the entire warning system.

The selection of the mounting location for this Informer15 Speaker, its controls and the

routing of the wiring are to be accomplished under the direction of the Facilities Engineer

and the Safety Engineer. In addition, listed below are some other important safety

instructions and precautions you should follow:

• Electrocution or severe personal injury can occur when performing various

installation and service functions such as making electrical connections, drilling

holes, or lifting equipment. Therefore only experienced electricians should install

Safety Messages

Informer15 Speaker (Model I-IP15)

this product in accordance with national, state and any other electrical codes having

jurisdiction. Perform all work under the direction of the installation or service crew

safety foreman.

• Read and understand all instructions before installing, operating, or servicing this

equipment.

• This product shall be mounted at the minimum hearing distance of ten feet in

accordance with FEMA guidelines limiting sound level exposure to 123 dBc

maximum sound level.

• All effective warning sounds may, in certain circumstances, cause permanent hearing

loss. Take appropriate precautions such as wearing hearing protection. Maximum

sound level exposure limits specied in OSHA 29 CFR 1910 should not be exceeded.

• These devices are intended for permanent installation and operation in accordance

with Title 46, Code of Federal Regulations, Parts 110–113, or Title 33, Code of

Federal Regulations, Part 183, Sub-part I, Section 183.410, and the applicable

requirements of the American Boat and Yacht Council, Inc., and/or ANSI/NFPA 302,

“Fire Protection Standard for Pleasure and Commercial Motor Craft.”

• For optimum sound distribution do not install this speaker where objects would block

any portion of the front of the Informer15 Speaker.

• Do not paint the Informer15 Speaker. No nish or coating is required. Paint may

obstruct the sound output, reducing the effectiveness of the horn.

• Establish a procedure to routinely check the signal system for proper activation and

operation.

• Any maintenance to the unit MUST be performed by a trained electrician in

accordance with NEC Guidelines and local codes or a Federal Signal certied

Service Provider.

• Never alter the unit in any manner.

• The nameplate should NOT be obscured, as it contains cautionary and/or other

information of importance to maintenance personnel.

• After installation and completion of initial system test, provide a copy of these

instructions to all personnel responsible for operation, periodic testing, and

maintenance of the equipment.

• File these instructions in a safe place and refer to them when maintaining and/or

reinstalling the device.

Failure to follow all safety precautions and instructions may result in property damage,

serious injury, or death.

Safety Messages

Description, Specications, Installation, Operation, and Service Manual

Installation and Service

• After installation or service, test the system to conrm that it is operating properly.

Test the system regularly to conrm that it will be operational in an emergency.

• If future service and operating personnel do not have these instructions to refer to,

the system may not provide the intended audible warning and service personnel

may be exposed to death, permanent hearing loss, or other bodily injury. File these

instructions in a safe place and refer to them periodically. Give a copy of these

instructions to new recruits and trainees. Also give a copy to anyone who is going to

service or repair the Informer15 Speaker.

• To reduce the risk of electric shock, do not perform any servicing other than what

is contained in the operating instructions unless you are qualied to do so. Refer all

servicing to qualied service personnel. Always test the Informer15 Speaker before

using after repairs have been made.

Ethernet Wiring

• Unless shielded or run in conduit, Ethernet wiring must be at least six feet from bare

power wiring or lightning rods and associated wires, and at least six inches from

other wire (for example, antenna wires, doorbell wires, wires from transformers to

neon signs), steam or hot water pipes, and heating ducts.

• Do not place Ethernet wiring or connections in any conduit, outlet or junction box

containing high voltage electrical wiring.

Symbol Denition

_A _V Indicates to reduce the risk of re, replace fuse as marked.

Pay careful attention to the notice located on the equipment.

Read and understand the information contained in this manual before

attempting to install or service the siren.

General Description

Informer15 Speaker (Model I-IP15)

General Description

Overview

The Informer15 Speaker is a 15-watt, IP-enabled indoor and outdoor speaker. The

Informer15 can be used as a warning and alert device with both audible and visual

indicators. The audible capabilities include locally stored high-quality, high-powered

tones and voice messages. The visual indicators include the use of message board/

scrolling display sign support, strobes, lights, and beacons. The Informer15 can be

equipped with up to four local initiation devices (switches) to activate the unit locally and

to the Commander® controller for mass notication communications.

The Informer15 Speaker has an internal 15-watt amplier/driver to deliver tone warnings

and intelligible voice messages from Informer15 stored memory. The Informer15 also has

several unique capabilities when working with the Federal Signal Commander software.

Using Commander software, the Informer15 can play text-to-speech, stream WAV les

or can broadcast live PA. In addition, Commander software can perform a talk/listen to

individual Informer15’s to allow call box type communications. The Informer15 also has

remote volume control for optimizing sound levels across your alerting area. The remote

volume control also includes an ambient-noise-monitoring capability to automatically

adjust volume depending on external noise levels.

The Informer15 allows connection of up to four external switches to activate predened

alert events. The Informer15 can be programmed and congured as a standalone device

to only use the inputs to activate the Informer15. This may be useful if the location has

no network connectivity, but where voice and tone alerts from locally activated inputs is

required. The Informer15 can be networked later and the activations can be brought into

the Commander system for full system capability. When the Informer15 is networked

using the Commander software, alerts initiated at the Informer15 can be used to activate

other devices. The Commander software system can also alert emergency personnel via

email, SMS, and handheld radios using optional messaging software.

The Informer15 includes one output to control the visual indicator and output to activate

external relay, which can be used to control external devices. The Informer15 has two

1/2-inch NPT opening on the bottom of the speaker for simple installation of pipe-

mount devices. The openings allow access to LAN, open collector output, and activation

inputs. The Commander system allows multiple congurations for activation of the open

collector output or visual indicator during alerts.

The Informer15 is designed for outdoor use and large indoor structures. It is powered

from the local switch through PoE. All wiring interfaces are accessible via internal

connectors and built-in NPT entrances for quick and easy installation.

The Informer15 Speaker is a perfect addition to existing notication systems where lack

of coverage exists. The unit can be used as a call station where emergency alert buttons

are required.

General Description

Description, Specications, Installation, Operation, and Service Manual

Features

The Informer15 has the following features; some features require the use of the

Commander software system:

• Outdoor or indoor IP-enabled speaker for audible and visual alerts

• Speaker rated at 112 dB for tones and 107 dB for pink noise at 10 feet

• Seven standard built-in warning signals: Wail, Steady, Alternate Wail, Alternate

Steady, Pulsed Wail, Pulsed Steady, Auxiliary Chime

• Broadcasts live voice, text-to-speech, and prerecorded voice or tone les

• Deliver intelligible voice messages from locally pre-recorded les or through the

Commander system

• Pre-recorded les: up to 4000 messages with 17 hours of recording time

• Ambient-noise-level monitoring with automatic volume control

• Each device can be remotely congured for volume and noise-level adjustments

• Speaker as microphone for talk-back feature

• Alerts can be sent to single devices, groups or zones, or all devices

• Wall mount

• Four local alarm initiation inputs to activate unit locally or standalone operation

Momentary mode: contact closure sounds alarm for programmed duration.

Continuous mode: sounds alarm for duration of closure.

• One open collector output paired with 24 Vdc for controlling an external relay

• High-intensity LED light that can be activated independently or with messages

• Models available with white, red, amber, blue, and green LEDs

• Wide variety of ash patterns

• Can be powered from 24 Vdc or via PoE

• Power over Ethernet using 802.3at PoE+ 25.5 W

• Wide operating temperature range

• Federal Signal Commander software provides activation, full two-way control, and

status monitoring

• Allows remote software upgrades

• US/Canadian ETL Listed to UL Std 60065

• Complies with FCC Title 47, Part 15

Specications

Informer15 Speaker (Model I-IP15)

Ordering Information

Table 1 Ordering Information

Part Number Description

I-IP15-C 15 W PoE Speaker with clear high-output LED

I-IP15-R 15 W PoE Speaker with red high-output LED

I-IP15-A 15 W PoE Speaker with amber high-output LED

I-IP15-B 15 W PoE Speaker with blue high-output LED

I-IP15-G 15 W PoE Speaker with green high-output LED

Specications

Table 2 Electrical Requirements

Input Voltage Power over Ethernet (PoE+ 802.3at) or 24 Vac (20-28 Vdc)

nominal

Input Current Draw PoE+ 25.5 W or 24 Vdc at 1 A

Serial Port Protocol FLASH programming and conguration

Default: 9600 bit/s, 8 data, 1 stop, no parity.

Congurable up to 115,200 bit/s

Open Collector Output Maximum 30 V or 100 mA maximum,

(speaker provides +24 Vdc, 20 mA maximum for external

relay)

Ethernet Port IEEE 802.3, 10/100 Base-T connection with PoE+ 802.3at,

Type 2, 25.5 W

Alarm Initiating Inputs Four optically Isolated Inputs

Audio Storage Warning siren audio, seven factory installed tones: Wail,

Steady, Alternate Wail, Alternate Steady, Pulsed Wail, Pulsed

Steady, Auxiliary Chime

Prerecorded les—up to 4000 messages with up to

17 hours of recording time

Audio Data 8 bit 8 kHz mono WAV

Audio Frequency response 300 Hz to 3000 Hz, +1 to -3 dB per octave

Maximum Audio Output 15 W, 112 dB for tones and 107 dB for pink noise at 10 feet

Power Output 15 W into 8 ohm load

Frequency response +/- 3 dB from 300-6.0 kHz

THD < 5% at output

Hum and Noise < -45 dB

Input Levels 1.77 Vrms (5 Vpp), 10 Vrms (28.3 Vpp) and 25 Vrms

(70.7 Vpp)

Table 3 Environmental

Operating temperature range -30°C to +65°C/-22°F to +149°F

Humidity range 0-95%, non-condensing

Andere Handbücher für Informer15 I-IP15

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Sprecher Handbücher

Federal Signal Corporation

Federal Signal Corporation 50GC Selectone Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IS-I-IP15 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MS100-01 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation BP100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AM50 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation ES100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global G-SPA-D Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation A12SA Installations- und Benutzerhandbuch

Federal Signal Corporation

Federal Signal Corporation Modulator MOD Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Global Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MicroPulse MPS U Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation AM300X Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation DS100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation R4NB Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MODULATOR Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation IS-I-IP15X Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MS100-01 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DSA1 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation 120 Series Montage- und Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SST3-MV Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation MS100 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GEN-IIB/C Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation BP200-EF Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation A12SA Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung