FIC AN19E Bedienungsanleitung

Quick Reference

The mainboard has several user-adjustable jumpers and/or switches on the board that

allow you to configure your system to suit your requirements. This quick reference

contains information on the various hardware settings on your mainboard.

To set up your computer, you must complete the following steps:

■ Step 1 - Set system switches/Jumpers

■ Step 2 - Install system memory modules

■ Step 3 - Install the Central Processing Unit (CPU)

■ Step 4 - Install expansion cards

■ Step 5 - Connect ribbon cables, cabinet wires, and power supply

■ Step 6 - Set up BIOS software

■ Step 7 - Set up supporting software tools

WARNING: Excessive torque may damage the mainboard. When

using an electric screwdriver on the mainboard, make sure that

the torque is set to the allowable range of 5.0 ~ 8.0kg/cm.

Mainboard components contain very delicate Integrated Circuit

(IC) chips. To prevent static electricity from harming any of the

sensitive components, you should follow the following precau-

tions whenever working on the computer:

1. Unplug the computer when working on the inside.

2. Hold components by the edges and try not to touch the IC

||||chips, leads, or circuitry.

3. Wear an anti-static wrist strap which fits around the wrist.

4. Place components on a grounded anti-static pad or on the bag

that came with the component whenever the components are

separated from the system.

4 - 2

AN19E/AN19CMainboardManual

Mainboard Layout

* When link to Line_Out jack, please use a speaker that with amplifier.

4 - 3

QuickReference

1). Clear CMOS, CPU Host Clock Select

2). Front Panel Block Cable Connection

CPU Host Clock Select

1-2: BIOS Setting (Default)

2-3: 133MHz

JCK1

JBAT

CMOS Clear

1-2: Normal (Default)

2-3: Clear CMOS

1

1

J3

J2

wPower On/Off

This is connected to the power button on the

case. Using Soft-Off by Pwr-BTTN feature,

you can choose either Instant Off (turns

system off immediately), or 4 sec delay (push

the button for 4 seconds before the system

turns off). When the system is in 4 sec delay

mode, suspend mode is enabled by pushing

the button momentarily.

wTurbo LED indicator

wIDE LED indicator

LED on when onboard PCI IDE Hard disks are

being accessed.

wIR Connector

1. VCC 4. GND

2. CIRRX 5. IRTX

3. IRRX

4 - 4

AN19E/AN19CMainboardManual

3). CPU Fan Installation

This connector is linked to the CPU fan. When the system is in some power saving

mode, the CPU fan will turn off; when it reverts back to full on mode, the fan will turn

back on. Without sufficient air circulation, the CPU may overheat resulting in

damage to both the CPU and the mainboard.

Damage may occur to the mainboard and/or the CPU fan if these pins are

used incorrectly. These are not jumpers, do not place jumper caps over these

pins.

wPower LED

Power LED connector

1. Power LED(+) 4.NC

2. N/C 5.GND

3. GND

wSpeaker

Connect to the systems speaker for beeping

1. Speaker 3.GND

2. N/C 4.VCC

wReset

Closed to restart system.

Andere Handbücher für AN19E

1

Dieses Handbuch passt für folgende Modelle

1

Andere FIC Hauptplatine Handbücher

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung