Fimap Minny 420 Montageanleitung

ADJUSTMENT

AND

INSPECTION MINNY 420-430-520 Doc. 10004810

Emesso dic - 06

Rev. 00

Pag. 1 di 6

READ THE OPERATING AND MAINTENANCE MANUAL

Electric circuit inspection

1. Check the functionality of the electric plant:

-brush motor (the motors runs when its switch

is on and when

the drive levers are activated)

-vacuum motor (switch on the vacuum motor by acting on its

switch on the left side of the control panel)

2. Check the double purpose of the display

placed in the centre of

the control panel:

-in working condition the display shows the charge level of the

battery (4 = charged, 0 = discharged)

-when all the switches are off the display ON alerts you the

solution cock is open.

3. Check the power connections are well tight. They are placed

in the electric circuit box placed on the rear part of the machine

(behind the rear panel).

4. Check conditions and the correct assembly of the fuses

ADJUSTMENT

AND

INSPECTION MINNY 420-430-520 Doc. 10004810

Emesso dic - 06

Rev. 00

Pag. 2 di 6

Adjustment battery check card

1. Check-up the right set-up of the battery check card. The

adjustment can be performed by microswitches.

2. The possibles configurations are the following:

The right configuration is one of the two above depending on the

battery type.

Inspection of the water supply unit

1. Fill the solution tank and check the no water leakage condition on

the pipe fitting connections on the solution cock and on the tap

for the drainage.

2. Check to have a uniformity in the water spreading on the floor and

that it is easily adjustable regulating the solution cock. In case

check the cleanness of the solution cock.

3. If the solution cock is obstructed remove the debris from the

opening Aafter the filter has been removed. Clean the solution

tank and leave the water drain from the opening A

24 V

Pb 24 V

Gel

36 V

Pb 36 V

Gel

ADJUSTMENT

AND

INSPECTION MINNY 420-430-520 Doc. 10004810

Emesso dic - 06

Rev. 00

Pag. 3 di 6

Inspection of the vacuum unit

1. Check the cleanliness and the functionality of the filter.

2. Check the air sealing of the tap (after it has been closed check the

gasket is perfectly lied down on the flange of the filter support).

3. Check that the rubber cuff is well inserted on the pipe and check

the good air sealing of the cuffs on the vacuum motor as well.

4. Check the good sealing of the gasket on the squeegee plastic

pipe.

Brush head adjustment Minny 420 - 520

1. Adjustment of the spring tension of the belt:

-Adjust the spring in order to have its length of 27 mm ( 1”).

2. Adjustment of the spring on the brush head point of attachment:

-Adjust the lock nut to have the length of the spring of 9

mm=1/3”.

-The right adjustment guarantees a soft and gradual pitch of the

brush head.

27 mm

1”

9 mm = 1/3”

ADJUSTMENT

AND

INSPECTION MINNY 420-430-520 Doc. 10004810

Emesso dic - 06

Rev. 00

Pag. 4 di 6

3. Adjustment of the roll inclination of the brush head:

-Place the machine on a level and regular floor

-Fit the brushes and lower down the brush head on the floor.

-Loosen the nut on the left lifting arm and leave free the brush

head to lie down on the flat floor (move a little the machine to

help the complete accommodation)

-The slot of the bracket will be positioned correctly

-Tight the nut and fix the adjustment.

This operation guarantees the correct roll alignment of the brush head

on the floor in working condition in order to have an uniformity

cleaned track on the floor.

Adjustment of the traction unit

-Loosen the lock nut and adjust the screw:

-screw to get more traction effect

-unscrew to decrease the traction effect

-Block the adjustment with the lock nut .

Adjustment of the splash guards

Adjust the height of the splash guards in order to have a distance

of about 1cm = 1/3” in the front of the brush head.

The rubber must touch the floor in the rear part

Brush deck adjustment (Model Minny 430)

Adjustment of the deck tilt/adjustment of traction

In order to adjust the traction operate upon the screw in the picture

after having loosen the knob:

-Unscrew in order to increase the traction effect

-Screw in order to decrease the traction effect

Fix the Knob after the adjustment.

Attention: increasing the traction of the machine, the working capacity

lower.

ADJUSTMENT

AND

INSPECTION MINNY 420-430-520 Doc. 10004810

Emesso dic - 06

Rev. 00

Pag. 5 di 6

Regulation touching of the brush

Check that the round head screw on the back side is adjusted

close to the flat upper face of the brush. The gap between the head

and the brush must be 1-2 mm maximum when the brush is hooked

and lowed.

Squeegee adjustment

1. Adjustment of the lifting unit

-Release the lock nut

-Screw the threaded rod in order to have the head of the rod just

outside the base of the fork (max 1 mm)

-Lock the nut to fix the adjustment

2. Squeegee adjustment

-The rubbers should have an inclination of about 45° along all tje

squeegee length

-To get the correct inclination act on the knob

for the squeegee

height adjustment (left and right side separated).

-To adjust the inclination use the metal knob

and the fix the

adjustent and block the black plastic lock hand wheel.

Just outside the

base of the fork

about 45°

Rear rubber Front rubber

ADJUSTMENT

AND

INSPECTION MINNY 420-430-520 Doc. 10004810

Emesso dic - 06

Rev. 00

Pag. 6 di 6

Functional inspection of the machine

Check the funtionality of switches and lamps;

Check the brush assembly funtionality;

Check the funtionality of brush motor;

Check the funtionality of the squeegee;

Check the funtionality of suction motor;

Check the funtionality of handbrake;

Check the conditions of battery connectors and cables;

Functional test of the machine

Fill the tanks with water and check their tightness;

Check that solution fall on the brushes equally;

Check the squeegee wheels with a functional test;

Adjust the brush pressure and the brush assembly inclination doing a functional test;

Check the funtionality of the water cock;

Check the braking efficiency;

Final inspection

Check all the main function: cleaning, drying , drive.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fimap Bodenreinigungsmaschine Handbücher

Fimap

Fimap Broom Bedienungsanleitung

Fimap

Fimap GENIE BS Bedienungsanleitung

Fimap

Fimap MXR Gebrauchsanweisung

Fimap

Fimap MR60 B Bedienungsanleitung

Fimap

Fimap FM33 Bedienungsanleitung

Fimap

Fimap MMg base Montageanleitung

Fimap

Fimap FS700 H Bedienungsanleitung

Fimap

Fimap FM43 ORBITALE Bedienungsanleitung

Fimap

Fimap FM1500 S Bedienungsanleitung

Fimap

Fimap ENJOY 360 Leitfaden

Fimap

Fimap FSR Bedienungsanleitung

Fimap

Fimap BMg Sanitizer Bedienungsanleitung

Fimap

Fimap 1500 S-V Bedienungsanleitung

Fimap

Fimap FSR B Bedienungsanleitung

Fimap

Fimap FM43 ORB Bedienungsanleitung

Fimap

Fimap MAGNA 85 BS Referenzhandbuch

Fimap

Fimap FM43 F Bedienungsanleitung

Fimap

Fimap FM4017 Bedienungsanleitung

Fimap

Fimap MR60 Bedienungsanleitung

Fimap

Fimap FS50 B Bedienungsanleitung

Fimap

Fimap FS80 B Bedienungsanleitung

Fimap

Fimap Mx Series Bedienungsanleitung

Fimap

Fimap Magna 1300 Bedienungsanleitung

Fimap

Fimap FS50 B-BT Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch