First Data FD-400 Bedienungsanleitung

Warning:

A shielded-type power cord is required in order to meet FCC emission

limits and also to prevent interference to the nearby radio and television

reception. It is essential that only the supplied power cord be used.

Use only shielded signal cables to connect I/O devices to this

equipment.

You are cautioned that changes or modifications not expressly

approved by the party responsible for compliance could void your

authority to operate the equipment."

First Data Corporation

c/o Tasq Technology

800-835-3362 Ext. 0

http://www.firstdata.com/

Printed in the United States of America.

PORTABLE TERMINAL

FD-400

INSTALLATION GUIDE

1. POWER ON TERMINAL

There are two holes under a plastic cover on the

right side of terminal (Figure 1).

One is power input, another is a port for devices

connected to terminal (Figure 2). (Adapter Input:

100-240V, 50/60Hz 1A; Output: 12V, 3.33A)

Rechargeable battery is on the back side of terminal

(Figure 3). (Lithium ion battery pack: 7.4V, 2.2A)

After plugged power cord or installed the battery,

press the power button on the frontto power on it

(Figure 4).

Caution: Risk of explosion if the battery is replaced

by an incorrect type. Please dispose of used battery

according to the instructions.

Environment:

Operating Temperature: 0°C to 40°C

Storage Temperature: - 20°C to 60°C

2. LOADING THE PAPER

Pop the printer cover’s latch to open the cover

(Figure 5); then lift the cover.

Load a roll of paper (Appleton 1012 recommended)

into the printer (Figure 6). The print-side of the

paper will feed out facing the operator.

Close the cover and tear off any excess paper

(Figure 7).

The printer is now ready to use.

Caution: For body worn operation, this terminal

will keep away 20cm from the body in orderto

meet the FCC RF exposure guidelines

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6

Figure 7

3. USING THE CARD READER

Find the reader slot in the middle of surface. Swipe

card through slot in left to right or the opposite

direction with stripe face to us (Figure 8).

Find the reader slot on the bottom. Insert smart card

into slot with IC chip to face up (Figure 9).

4. USING THE KEY PAD

The keypad allows you to select transaction types

and enter information. Its 16 keys can be used to

select numbers, letters, and to enter data (Figure 10).

To enter numbers or letters, simply press the

appropriate key. For example, to type the letter A,

press [ALPHA], then [A] (the Void key) (Figure 11)

Figure 8

Figure 9

Figure 10

Figure 11

Federal Communications Commission Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the foll

owing two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that m

ay cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B d

igital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro

vide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if no

t installed and used in accordance with the instructions, may cause harmful interfe

rence to radio communications. However, there is no guarantee this equipment do

es not cause harmful interference to radio or TV reception. This can be determined

by turning the equipment on and off. The user is encouraged to try to correct the in

terference by one or more of the following measures:

zReorient or relocate the receiving antenna.

zIncrease the separation between the equipment and receiver.

zConnect the equipment into an outlet on a circuit different from that to whi

ch the receiver is connected.

zConsult the dealer or an experienced radio or television technician for hel

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS

AUTHORITY TO OPERATE THE EQUIPMENT.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment . End users must follow the specific operating

instructions for satisfying RF exposure compliance. To maintain compliance with

FCC RF exposure compliance requirements, please follow operation instruction as

documented in this manual.

For hand-held or desktop operation only. This PORTABLE TERMINAL meets

FCC RF exposure guidelines when used in hand-held or desktop operation.

Andere First Data Zahlungsterminal Handbücher

First Data

First Data FD200Ti Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

First Data

First Data FD100 Bedienungsanleitung

First Data

First Data FD100 Bedienungsanleitung

First Data

First Data FD40 Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

First Data

First Data FD-400GT-CDMA Bedienungsanleitung

First Data

First Data FD35 PIN Pad Bedienungsanleitung

First Data

First Data FD 150 Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

First Data

First Data FD 150 Bedienungsanleitung

First Data

First Data Move5000 Bedienungsanleitung

First Data

First Data FD-30 PIN Pad Bedienungsanleitung

First Data

First Data XAC Bedienungsanleitung

First Data

First Data 8006L2-3CR Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

First Data

First Data nashville linkpoint 3000/aio Bedienungsanleitung

First Data

First Data OMNI 3750 Bedienungsanleitung

First Data

First Data RP10 Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

First Data

First Data FD400 Bedienungsanleitung

First Data

First Data FD300Ti Bedienungsanleitung

First Data

First Data FD130 Bedienungsanleitung

Beliebte Zahlungsterminal Handbücher anderer Marken

PAX

PAX D180SRF Bedienungsanleitung

LinkPoint

LinkPoint AIO Bedienungsanleitung

Moneris

Moneris hispeed 6200 Bedienungsanleitung

Moneris

Moneris iWL220 Bedienungsanleitung

Ingenico

Ingenico iUC280 Bedienungsanleitung

Ingenico

Ingenico Tetra Move/5000 Bedienungsanleitung

Ingenico

Ingenico iWL250B Bedienungsanleitung

Optimum

Optimum M4230 Bedienungsanleitung

Triton

Triton RL5000 Bedienungsanleitung

Ingenico group

Ingenico group Lane/8000 Bedienungsanleitung

Gilbarco

Gilbarco FlexPay IV CRIND Installations- und Betriebshandbuch

Infinite Peripherals

Infinite Peripherals Infinea Tab Lite Bedienungsanleitung

PAX

PAX S920 Bedienungsanleitung

Ingenico

Ingenico iCT220, iCT250 Bedienungsanleitung

dejavoo

dejavoo Z Series Bedienungsanleitung

VeriFone

VeriFone VX 520 Series Bedienungsanleitung

Optomany

Optomany axept S900 Bedienungsanleitung

Skyzer

Skyzer iWL252 BLUETOOTH Bedienungsanleitung