Fixturlaser SMC Bedienungsanleitung

USER MANUAL Fixturlaser SMC

USER MANUAL FIXTURLASER SMC, edition 1.3 (November 2017)

CONTENT

General presentation

1.1

General settings

2.1

Supervisor module

3.1

Balancing module

4.1

Maintenance

5.1

Technical specification

6.1

1.1

1 GENERAL PRESENTATION

1.1 INTRODUCTION

We want to congratulate you on your choice and hope that you will be fully satisfied with it. For this

reason, we recommend that you read carefully the present user guide and more specifically the safety

instructions.

Designed to meet industrial requirements for enhancing productivity, FIXTURLASER SMC is a portable

multichannel instrument coming along with a large touchscreen, a 3-axis wireless sensor and numerous

accessories. This innovative all-in-one solution makes vibration analysis available to all users.

FIXTURLASER SMC is available in 2 versions. The FIXTURLASER SMC standard (red rubber) is for

safe area, and the FIXTURLASER SMC-EX (black rubber) for ATEX Zone II area. Always refer to the

product marking to know which version you are using. All functionalities described in this manual are

applicable to both versions.

1.2 SAFETY INSTRUCTIONS

The safety instructions delivered with the instrument (printed and on the USB stick) should be carefully

followed and the instrument should always be used within the limits specified here.

Instrument and operator safety is at risk when the instrument is used in conditions that are not

intended by ACOEM.

Dismantling the instrument for an internal operation is forbidden. The only parts for which dismantling is

allowed are the battery hatch, the battery and the hatch providing access to the connectors.

All the spare parts must be provided by ACOEM.

1.2

List of symbols and warning on the instrument

Warning: Whenever this symbol is present on the device, refer to the safety instructions and user

manuals.

The table below lists the warning signs and security present on the instrument.

Symbol

Signification

Position

Laser radiation

Refer to section "Laser Class 3R"

Rear side (bottom)

Laser radiation class 3R

Refer to section "Laser Class 3R"

Rear side (bottom)

Avoid exposure to beam

Refer to section "Laser Class 3R"

Rear side (bottom)

Light Hazard Group 2

Refer to section "High-power white LED

flash and stroboscope"

Rear side (bottom)

Refer to the safety instructions

documentation and the user manual

before connecting

Rear side (bottom)

Laser aperture

Refer to section "Laser Class 3R"

Rear side (top)

Battery replacement

Refer to section "Battery pack set-up"

Battery compartment

CE certification data. Refer to the copy of

the CE APT2069 type certificate

Rear side (center)

Do not dispose of this product as unsorted

household waste.

Refer to section "Dismantling/recycling"

Rear side (center)

FCC and IC number. Refer to section

"Radio"

Rear side (center)

External power connection: refer to

section "Main Power supply block"

Rear side (bottom)

List of symbols and warning on WLS

Warning: Whenever this symbol is present on the device, refer to the safety instructions and user

manual.

The table below lists the warning signs and security present on the WLS sensor.

Symbol

Signification

Warning: Refer to the safety instructions

and user manuals

Use a power source with limited power

(=> Mains Power supply bloc)

=> CE certification data

=> Dismantling/recycling

1.3

Laser

Laser maintenance: The laser does not need maintenance or adjustment excluding cleaning the glass

with a cotton swab. Always shut off completely the device FIXTURLASER SMC before this operation.

Caution: Use of controls or adjustments or performance of procedures other than those specified herein

may result in hazardous radiation exposure.

Electric connections

All external circuits connected to the instrument must be non-hazardous voltage sources and be energy

limited as explained in sections 6.3 and 9.4 of the IEC61010-1 standard.

Do not exceed maximum input voltage on the A/B/C/D connectors: Maximum input voltage ±24 V DC,

±24 V AC peak.

All external circuits connected to the instrument must carry non-dangerous voltage as defined in

Standard IEC61010-1 (Paragraph 6.6)

Do not exceed maximum input voltage and current intensity for the power supply delivered by the mains

block (see chapter “Mains power block” of the safety instructions).

Use the cables designed for the different types of measurement.

If possible, protect the unused connectors using the plastic caps provided.

1.4

1.3 FIRST POWER UP

The instrument turns on automatically a few seconds after being connected to the mains through the

power supply module. If the battery level is too low, the charge starts and goes on as long as the

instrument is connected to its power supply.

When using a new battery, leave the battery in charge for about 10 hours in order to achieve full charge.

Do not use the instrument prior to 2-3 hours of charge. Usual charging time is about 6 hours when

instrument is switched off.

On-Off

•Power on: Press the On-Off key

•Power off: Press the On-Off key, then message “Shutdown”

Battery charge

•Power off: Press the On-Off key, then message “Shutdown”

•Connect the charger on the main. The instrument is automatically powered on. During the charge,

you can continue to use it. For a faster charge, it is recommended to switch-off the instrument. A full

charge requires about 6 hours.

It is recommended to disconnect the charger from the main when you are not using it.

1.5

1.4 USER INTERFACE

FIXTURLASER SMC starts on its “Home screen”. It is a touch screen and a simple pressure on it gives

access to the application modules installed on the instrument and to 2 side panels:

For more details:

•Supervisor module: See CHAPTER 3

•Balancing module: See CHAPTER 4

•Status panel: See § 1.9

•Shortcuts panel: See § 1.10

The 2 side panels are accessible from any screen.

Access to

application

modules

Access to

status side

panel

Access to

shortcuts side

panel

1.6

1.5 CONNECTIONS

Connectors A to D on the top of the instrument

Those connectors can be used in industrial environment. They are IP65

Connector A

Channels 1. Use this connector when the instrument is set in single-channel mode.

•Contact A:

•Contact B: Common

•Contact C: Channel 1 signal input

•Contact D:

•Contact E: Channel 3 signal input

•Contact F: -24 Vdc output

Connector B

Channels 2, 3 and 4. Use this connector with wired triaxial sensor when the instrument is set in multi-

channel mode.

•Contact A:

•Contact B: Common

•Contact C: Channel 2 signal input

•Contact D: Channel 3 signal input

•Contact E: Channel 4 signal input

•Contact F: -24 Vdc output

Notes

For 2-channel measurement, use connectors A and B

If inputs are set as IEPE, the sensor is powered by a 4 mA constant current. The integrity of the sensor

is monitored and a warning is issued if peak voltage is out of about 1 to 22 V.

Antenna for WLS

sensor and Wi-Fi

Inhaltsverzeichnis

Andere Fixturlaser Messgerät Handbücher

Fixturlaser

Fixturlaser NXA Pro Montageanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung