Flex FLEXJET TV SUPER PNP Bedienungsanleitung

The FlexJet TV is designed to be a high-performance, 3D-capable (post-stall manuevering) EDF. It is

capable of aerobatics and 3D manuevers such as hovers, flat-spins, pin-wheels, tumbles, and more!

To achieve this manuevering capability, The FlexJet TV has approximately 90% more power than the

original FlexJet while remaining very light. This excess power is intended for uplines and 3D manuevers

only. Because of this, the pilot is required to limit the speed of the aircraft, and the G-Load on the Aircraft.

- Powered dives are not permitted

- Extended level flight at full throttle is not permitted

- High-Speed, High-G manuevers are not permitted

- Limited to maximum of 20MPH (32km/h) of wind speed or gust

Over-speeding or over-stressing the aircraft can result in structural failure and a crash, which may also

cause personal injury and/or property damage.

NOTICE

DAMAGED PRODUCT(S), INJURY AND/OR PROPERTY DAMAGE CAUSED BY FAILURE TO

FOLLOW THE ABOVE GUIDELINES IS NOT COVERED UNDER WARRANTY.

If you as the Purchaser or user are not prepared to accept the liabity associated with the use of the Product, you are

advised to return this product immediately in new and unused condition to the place of purchase. In the event you wish to

return this product, as the Purchaser or user, you are responsible for return shipping.

For more information regarding returns please visit:

https://www.flexinnovations.com/returns.asp

BEFORE CONTINUING WITH THIS INSTRUCTION MANUAL OR ASSEMBLY

OF YOUR AIRCRAFT, PLEASE VISIT OUR WIKI SUPPORT SITE FOR THE

LATEST PRODUCT UPDATES, FEATURE CHANGES, MANUAL ADDENDUMS

AND FIRMWARE CHANGES FOR BOTH YOUR AIRCRAFT AND THE

INSTALLED AURA 8 ADVANCED FLIGHT CONTROL SYSTEM.

wiki.flexinnovations.com/wiki/FlexJetTV

wiki.flexinnovations.com/wiki/Aura

BOX CONTENTS

TABLE OF CONTENTS

INTRODUCTION

On behalf of Flex Innovaons, thank you for purchasing

the FlexJet TV!

The FlexJet TV combines a proven plaorm of modern aerodynamics with

sport jet praccality and performance with an 8s Power System with a thrust

vectoring nozzle for added capability in post-stall ight.

Trailing link landing gear, and the wing's wide angle of aack range, along

with Aura 8 make takeos and landings easy. Aerobacs are eortless and

impressive. The FlexJet TV excels at harriers, hovers, at-spins, tumbles,

unlimited vercal maneuvers, and high alpha manuevers.

For the latest updates, features, addendums and more, before assembly,

please visit:

hp://wiki.exinnovaons.com/wiki/FlexJetTV

Airframe Advisory

Wiki Advisory

Introduction

Box Contents

Specifications

Replacement Parts

Optional Accessories

Completion Items

Battery Charging Guidelines

Special Language Definitions

Important Information Regarding Warranty

Safety Warnings and Precautions

Low Voltage Cutoff

Aura 8 AFCS

Transmitter Setup

Reciever insatllation/Aura Setup Note

Connecting a Battery/Arm ESC

Reciever Installation/Servo Connections

Retracts/Gear Sequencer Operation

EDF Access Hatch, Tail Pipe, Exhaust Nozzle Removal

Flying Stabilizer Installation

Wing Installation

Battery Installation

Vertical Stabilizer Installation

EDF Access Hatch, Tail Pipe, Exhaust Nozzle Re-installation

Thrust Vector Nozzle Setup

Missile Rail Installation

Transmitter Control Test

Flight Control Sensor Test

Center of Gravity

Pre-Flight Checks

Flying your FlexJet TV

Advanced FlexJet TV Aura Configuration

Airframe Repairs

Replacing Servos

Servicing the Power System

Aircraft Troubleshooting Guide

Limited Warranty

AMA Safety Code

Elevator Trim Gauges

9, 10

...............................................................

......................................................................

.........................................................................

......................................................................

.....................................................................

.............................................................

.........................................................

...............................................................

..............................................

............................................

........................

......................................

.............................................................

......................................................................

...............................................................

..............................

.........................................

..........................

....................................

....

.......................................................

.........................................................................

.....................................................................

.....................................................

...

.......................................................

...............................................................

............................................................

.........................................................

........................................................................

......................................................................

................................................................

..................................

........................................................................

.......................................................................

......................................................

..................................................

........................................................................

......................................................................

................................................................

12, 13

15, 16

Custom-tuned Aura 8 gyro stabilizaon system provides

the ulmate in stability and control

Powerful 80-sized in-runner motor provides ecent

power

120amp 8s ESC provides reliable power

11-bladed 90mm fan for outstanding thrust and sound

Electric retracts with metal pivot

High deecon thrust vector nozzle gives unparraelled

control in post-stall ight.

Electric gear doors with sequencer installed

Embedded carbon ber spars in wings and stabilizer

Custom-designed control horns to opmize control

geometry and performance

High-precision digital servos with metal gears

Lightweight EPO foam is s and tough

COMPLETION ITEMS

Potenza 80-DF BL 1500 Kv

Brushless In-runner Motor

(FPZM1080DFA)

Potenza DS15 Digital Servos (QTY: 7)

(FPZDS15B)

Aura 8 Advanced Flight Control

System (FPZAURA08ZZFTV)

90mm EDF Fan Assembly

(FPMDF90A)

3500-4200mAh 8S 29.6V 40C+ Li-Po

(8S 4000mAh 70C: FPZB40008S75)

NEEDED TO

COMPLETE

INSTALLED!

SPECIFICATIONS

41.6 in. (1056mm)

55.1 in. (1400mm)

Standard: 7.1lb (3220g)

RTF with 8S 4000mAh ba�ery installed

(QTY:2 Required for

JR DMSS Mode B)

(Recomended

Spektrum Receiver)

(Recomended

FASSTest Receiver)

(QTY:2 Required

to make 8S pack )

(Not compatible

with 8S Li-Po)

BATTERY CHARGING GUIDELINES

The assembly of the FlexJet TV can be accomplished in 1-2 hours.

Prior to assembling the airplane, it is advisable to charge your

battery so that you are ready to begin setup upon completion of the

assembly of your model.

We recommend the use of an advanced Li-Po balancing charger

capable of 8S. A 4S charger can be subistuted if using QTY:2 4S

Li-Po's in series.

The FlexJet TV was designed around the Potenza Li-Po Hyper

Series 8s 4000mAh 75C Li-Po battery (FPZB40008S75) or QTY:2

Potenza Li-Po Hyper Series 4s 4000mAh 75C Li-Po batteries

(FPZB40004S75) in series. In our extensive testing and

development of the FlexJet TV, these batteries provided the best

combination of power, weight, and flight time. In addition, these

batteries feature an EC5 connector, so no soldering is required for

use in your FlexJet TV.

Potenza Li-Po batteries are available at www.flexinnovations.com

WARNING

FOLLOW ALL INSTRUCTIONS PROVIDED BY YOUR

BATTERY AND CHARGER MANUFACTURER.

FAILURE TO COMPLY CAN RESULT IN FIRE.

OPTIONAL ACCESSORIES

INSTALLED!

REPLACEMENT PARTS

FPZB40008S75

FPZB40004S75

FPZA1026

FPZA1010

SPMAR8010T

FUTR7008

FUTR2008

FPZA1012

ISDTD2

Potenza 8S 4000mAh 75C Li-Po

Potenza 4S 4000mAh 75C Li-Po

Potenza EC5 Series Connector

Potenza Digital Battery Analyzer

Spektrum AR8010T Reciever

Futaba R7008SB Reciever

Futaba R2008SB Reciever

Potenza 2" Y-Harness

iSDT D2 Smart AC Charger 100w x2 6s

Receiver

NEEDED TO

COMPLETE

6CH + MODERN DIGITAL

CONNECTION: SRXL, Futaba or

Hitec S.Bus, Graupner HOTT, Jeti

UDI, JR DMSS XBus

NEEDED TO

COMPLETE

INSTALLED!

Potenza DS12 Digital Servos (QTY: 4)

(FPZDS12 / FPZDS12R)

FlexJet TV Fuselage Orange (No Hatches)

FlexJet TV Canopy and Fan Hatch Orange

FlexJet TV Nose Cone / Tail Pipe Orange

FlexJet TV Pushrod Set

FlexJet TV Light Weight Wire Strut Set

FlexJet TV Light Weight Foam Wheel Set

FlexJet TV Fwd. Wing Skin Reinforcement

FlexJet TV Thrust Vectoring Nozzle

L+R Wing Set Orange

L+R Stab and Fin Set Orange

Ventral Fin and Missle Rail Set Orange

Wing + Fin Carbon Fiber Tube Set

Orange Decal Set

Pushrod Set

Hardware Package

Landing Gear Struts

Landing Gear Rubber Strut Downstop Set

Wheel Set

Doors, Hinges, Misc. Plastic Parts

Metal Clevis Set (4)

90mm EDF Fan Assembly (No Motor)

Potenza 3-Piece Retract Set

Potenza Electric Retract (single)

Potenza Gear/Door Sequencer

Potenza DS15 Servo Arm and Screws Kit

Potenza DS15 MG Digital Servo w/165mm

Potenza DS12 MG Sub-Micro Servo

Potenza DS12 MG Sub-Micro Reverse Servo

V-Good 120 HV ESC

HobbyWing 120 HV ESC

Aura 8 AFCS for FlexJet TV

Potenza 80 1500KV EDF Inrunner Motor

INSTALLED!

(FPZEDFHW120BEC)

HobbyWing 120 HV ESC

V-Good 120 HV ESC

(FPZEDFVG8S120BEC)

(Recomended

S-FHSS Receiver)

OPTIONAL ACCESSORIES (CON'T)

ISDTT8

iSDT T8 Smart DC Battery Charger 1000w 8S

6+ Channel Computer Transmitter

6+ Ch. Receiver with 6-output ports and

Modern Digital Connection

WITH

FPM344001

FPM344007

FPM344014

FPM344015

FPM347018

FPM347019

FPM347020

FPMADFTV90

FPM347003

FPM347005

FPM347009

FPM347011

FPM347012

FPM347015

FPM347016

FPM347017

FPM347018

FPM347019

FPM347020

FPMA0004

FPMDF90A

FPZA1020

FPZA1020S

FPZA1021

FPZA1023

FPZDS15B

FPZDS12

FPZDS12R

FPZM180DFA

FPZAURA08ZZFJTV

FPZEDFHW120BEC

FPZEDFVG120BEC

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

SPECIAL LANGUAGE DEFINITIONS

ATTENTION

WARNING

AGES 14+

NOTICE:

CAUTION:

WARNING:

Procedures, which if not properly followed, create a possibility of physical

property damage AND a little or no possibility of injury.

Procedures, which if not properly followed, create the probability of physical

property damage AND a possibility of serious injury.

Procedures, which if not properly followed, create the probability of property

damage, collateral damage, and serious injury OR create a high probability of

serious injury.

Read the ENTIRE instruction manual to become familiar with the features of the

product before operating. Failure to assemble or operate the product correctly can

result in damage to the product, personal property, and cause serious or fatal injury.

All instructions, warranties and other collateral documents are subject to change at

the sole discretion of Flex Innovations, LLC. For up-to-date product literature, please

visit our website at www.flexinnovations.com, click on your aircraft and the Aura 8

AFCS product pages.

This product is not intended for

use by children under 14 years

without direct adult supervision.

IMPORTANT INFORMATION REGARDING WARRANTY

SAFETY WARNINGS AND PRECAUTIONS

Please read our Warranty and Liability Limitations section before building this product. If you as the Purchaser or user are not

prepared to accept the liability associated with the use of this Product, you are advised to return this product immediately in

new and unused condition to the place of purchase.

LOW VOLTAGE CUTOFF

Protect yourself and others by following these basic safety guidelines.

1. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the

instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or

serious injury.

2. This model is not a toy, rather it is a sophisticated hobby product and must be operated with caution and common sense.

This product requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could

result in injury or damage to the product or other property.

3. This model must be assembled according to these instructions. Do not alter or modify the model outside of these

instructions provided by Flex Innovations, Inc. as doing so may render it unsafe and/or unflyable. It is your responsibility to

ensure the airworthiness of the model.

4. Inspect and check operation of the model and all its components before every flight.

5. If you are not an experienced pilot or have not flown a high-performance model before, it is recommended that you seek

assistance from an experienced pilot in your R/C club for your first flights. If you're not a member of a club, the Academy of

Model Aeronautics (AMA) has information about clubs in your area whose membership includes experienced pilots.

6. Keep the propeller area clear from such items as loose clothing, jewelry, long hair, or tools as they can become entangled.

Keep your hands and body parts away from the propeller as injury can occur.

7. Never fly in visible moisture, or submerge the airplane or any of its electronic components in water. Permanent damage to

electronic components may occur, or corrosion of components may lead to intermittent failures.

Li-Po batteries have a nominal (rated) voltage of 3.7V per cell, and fully charged, reach 4.2V per cell. Batteries are designed to be

discharged below the nominal voltage, however, if they are discharged below 3.0V per cell, damage will occur and the pack will lose

capacity. For best long term battery life, set a timer and land after a time that leaves approximately 15% of the battery's capacity

remaining.

Low voltage cutoff is a feature that is built into the included ESC that is designed to protect the connected battery from being

discharged too far and causing permanent damage to the cells. Circuitry within the ESC will automatically detect when the input

voltage from the battery pack reaches below 3.15V per cell (average) and will remove power to the motor, but still deliver power to

the servos so that a safe landing may be made. If the motor begins to lose power rapidly during flight, the LVC has sensed that the

total voltage of the pack has dropped below 3.15V per cell average, and the airplane should be landed immediately.

AURA 8 AFCS

Works conveniently with all major radio systems

Accepts signals from Spektrum SRXL, Futaba S.Bus,

Graupner Hott (Sum D of 8), JR XBus (Mode B), Jeti UDI12

(standard), Hitec S.Bus, PPM Stream

Expertly tuned and ready to use

USB port allows loading model configurations, user

programming, and firmware updates (cable included)

Flexible and extensive programming through Windows-

based PC or tablet

3+ flight modes allow precise or aggressive settings to be

selected in flight

3-axis gyro utilized in FlexJet TV programming

Powerful 32-bit processor and multi-axis sensor for future

updates.

The Aura 8 Advanced Flight Control System (AFCS) installed in

your FlexJet TV is a giant leap forward in aircraft flight control

system technology. Compatible with virtually every receiver on the

market today, the Aura features special configuration for serial data

connection for Futaba or Hitec S.Bus, Spektrum SRXL, Graupner

HOTT (Sum D of 8), JR XBus (Mode B), and Jeti UDI12 (standard)

systems.

The Aura 8 advanced flight control system installed in your aircraft

has been pre-tuned for ease of use, eliminating many hours of

tedious setup. For the latest Aura features, programs, transmitter

downloads, and instructions, please visit wiki.flexinnovations.com/

wiki/Aura

The Aura is programmable through any Windows based PC or

tablet. All dual rate, expo, travel and assignable mode programs are

adjusted inside the Aura through the PC application. An assignable

master gain that is OFF by default can be enabled by the Aura

application. If desired, assign CH 8/AUX 3 on a proportional dial or

slider.

By default, CH6/Aux1 is used to select the 3 flight modes by 3

position transmitter switch. CH5/Gear is used to retract/deploy

the landing gear. Visit wiki.flexinnovations.com/wiki/Aura for the

latest Aura-related product information and

tips for your particular radio brand.

Description of Pre-Loaded Aura Flight Modes (FM)

Each of the modes has been tuned by the Flex Team to offer a solid start. Because tastes in control feel are unique, if changes in rates

and expo are needed, adjustments should be made through the Aura 8, not the transmitter..

Changes in gain value can only be made through the Aura or via master gain (if activated).

Flight Mode 1 (Test / Safety):

Gyro gain is set to off. All rates are set to low for general flight. Exponential is tuned for comfortable flight. Tailerons are active. Thrust

Vectoring is deactivated.

Flight Mode 2 (Sport / Precision):

Gyro gain is set to low. All rates are set to low for sport / precision flight. Exponential is tuned for comfortable flight. Tailerons are active.

Thrust Vectoring is active and set to moderate rates.

Mode 3 (3D Rate):

Gyro gains are high and tuned for low-speed post-stall flight. All rates are set to highest. Exponential is tuned for comfortable flight.

Tailerons are active. Thrust Vectoring is active and set to high rates. Do NOT fly at High Speed. Doing so may induce gyro

osciliations!!

TRANSMITTER SETUP

The Aura 8 AFCS is designed to work seamlessly with all major transmitter and receiver brands. When programming your transmitter, start

with a freshly reset new model memory in your transmitter. Make ONLY the changes shown in the Transmitter Configuration Guide

unless otherwise noted.

The Aura 8 in your FlexJet TV defaults to 3 flight modes that are switched via CH6/Aux1 in your transmitter. You may need to reassign

CH6/Aux to a 3-position switch.

The retracts in the FlexJet TV are operated via CH5/Gear in your transmitter. You may need to reassign that CH5/Gear in your transmitter to

a 2-position switch.

Consult your transmitter manual if you have questions on how to change the switch or channel assignments.

The Aura comes pre-programmed with dual rates and expos specifically designed for your aircraft. For large (greater than 5%) changes in

expo or dual rates, it is highly recommended to reset all expos and rates to default in the transmitter, and tune through the Aura Config Tool.

The Aura Config Tool is free to download, and can be used on any Windows-based PC or tablet. Download at:

www.flexinnovations.com/AuraConfigTool

JR transmitter users that use Spektrum DSM2/DSMX receivers should follow the Spektrum information in the chart

above.

If you are using a Futaba transmitter, please note that some Futaba transmitters have the throttle set to reversed by

default. Leave reversing set to defaults to start, and reverse as needed.

This aircraft can fly anywhere between 2:30 and 4 minutes (w/8S 4000mAh Li-Po), depending on flying style.

NOTICE

FOR CUSTOMERS USING TRANSMITTERS OTHER THAN WHAT IS LISTED IN THE CHART ABOVE, PLEASE VISIT

OUR WIKI PAGE FOR INSTRUCTIONS SPECIFIC TO YOUR TRANSMITTER AND RECEIVER BRAND

JETI

HITEC

FRSKY

wiki.flexinnovations.com/wiki/Aura/JetiUse

wiki.flexinnovations.com/wiki/Aura/HitecSbusUse

wiki.flexinnovations.com/wiki/Aura/FrSkyUse

TRANSMITTER CONFIGURATION GUIDE

End Points

(Travel Adjust

or ATV)

Ail/Ele/Rud/Gear

Throttle

125%

100%

Sub Trim

Verify at zero, NOT ALLOWED

Trim Levers

Verify at zero

CH.5 (Gear) Assigned to a 2-position switch

Reversing None Required

Timer

Wing/Tail Type

1-Aileron, 1-Elevator, 1-Rudder (No Flaps)

CH.6 (FM)

Spektrum, Futaba & Graupner

Set to 2:10 for initial flights

Assigned to a 3-position switch

JR DMSS wiki.flexinnovations.com/wiki/Aura/JRUse

During radio setup ensure motor is disengaged by unplugging all wire leads that connect the ESC to the motor.

CAUTION

CONNECTING A BATTERY/ARMING THE ESC

Lower the throttle stick and trim to their lowest setting and turn

on the transmitter. Wait for your transmitter to indicate the radio

signal is being broadcast before proceeding.

Ensure the aileron, elevator and rudder gimbals are centered.

With the airplane on a solid surface, connect the battery to the

ESC and wait. The ESC will make the motor emit a series of

audible tones during its intialization process.

The ESC will make the motor emit a short, final tone sequence

idicating that the ESC is now armed, and the motor will spin in

response to throttle stick movement.

If a battery is connected to the ESC with the throttle fully

open on the active transmitter, the ESC will enter

programming mode. If this occurs, simply disconnect the

battery, lower the throttle, and reconnect the battery.

WARNING

When making adjustments to linkages,

transmitter settings or the Aura 8 flight control

system, disengage motor by unplugging from

ESC to guard against accidental spool up.

Hold the aircraft securely when connecting the

battery before flight. Always ensure any and all

objects are clear of the duct inlets and EDF fan

unit as they may become entangled.

WARNING

Always connect the battery when the throttle stick

and throttle trim is in the idle/cut-off position.

CAUTION

RECEIVER INSTALLATION / AURA 8 INSTALLATION NOTE

Throughout the assembly process, we will ask you to power up the radio system. In order to assemble your FlexJet TV properly, It is critical

that the receiver is bound to your transmitter and is communicating with Aura 8. Please do not proceed until the Aura 8 emits a solid

green LED (Aura received valid signal from reciever) and solid orange LED (Aura has power and calibrated sensor) when powered

up. Please note, for all systems EXCEPT JR DMSS MODE B, you can temporarily plug a servo into the reciever's aileron port to verify that

your receiver is bound to your transmitter. In the event that you are having difficulties with radio or Aura 8 installation please see the

following:

For issues with your transmitter and/or reciever, please review your transmitter/receiver manual or contact the manufacturer directly.

For issues regarding Aura 8 please reference the following:

• Wiki page: wiki.flexinnovations.com/wiki/Aura

• Email us at [email protected]

• Contact Aura Support at 866-310-3539

While assembling the FlexJet TV, ensure motor is disengaged by unplugging all wire leads that connect the ESC to the motor.

CAUTION

Observe the following procedures to safely power up your model

after it has been bound. Ensure the motor is unplugged from

ESC unless sequence is followed to power up before flight.

Inhaltsverzeichnis

Andere Flex Spielzeug Handbücher

Flex

Flex Cessna 170 Bedienungsanleitung

Flex

Flex QQ Extra 300 Bedienungsanleitung

Flex

Flex YAK54 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung